💬 Air Humidity Sensor - DHT

[tiana]

For some sensors is possible to make with offset, but some of the sensors changing their values 2 times in minute with + - 2 degree Celsius some times show more sometimes show less.

[Anduril]

well I think this kind of noise can not be calibrated. I thought they all have different values, but with offset, linear oder squared function for deviation.

[tiana]

I read datasheet for DHT11 and 2 degree deviation is ok for them. Now i playing with DHT22 I try this #define SENSOR_TEMP_OFFSET -1.3, but nothing is changed the sensor still give me same value.

[mfalkvidd]

@tiana try setting SENSOR_TEMP_OFFSET to a really big value, for example -30.8 to make sure that the change is large enough to be noticeable.

[pepson]

Where i can found good DHT library for this sketch ?

[mfalkvidd]

@pepson how about the library linked from the build page?

[pepson]

sorry i found

[Jim Danforth]

Using library linked above
Getting: no matching function for call to 'DHT::readSensor(bool)'

[ramoncarranza]

@hek
hi, how do I change the readings from C to F?
My sensor works fine, by I get the readings I celsius

[mikeS]

@ramoncarranza
Change the line in the sketch:

temperature = dht.toFahrenheit(temperature);

to

temperature = dht.toCelsius(temperature);

probably? I haven't checked it, just looked at the DHT library. You may need to comment the isMetric line earlier in the sketch too. But I think that's how you do it.

[ramoncarranza]

@mikeS Thanks so much for your reply, it's working perfectly now.

[meanmrgreen]

@Jim Danforth
Getting the same, have tried a number of different DHT libraries and cant get it to compile.

[mikeS]

@meanmrgreen The only DHT library that will work is the one from the link before the sketch. If you have used others chances are you need to move or rename those other DHT libraries as that is why the sketch cannot call that function.

[meanmrgreen]

@mikeS

Ive tried to reinstall and start från scratch but i guess i Missed something.

[mikeS]

@meanmrgreen sometimes windows puts libraries in your documents folder, so they may be located in 2 or more places. Use windows search to find them all. I have 3 DHT libraries, the mysensors one, the adafruit(I think) and another that came with an MQTT based sketch for an ESP board. I just rename them. Incidentally the mysensors DHT library gives me the most accurate results, as much as 2 degrees and 10% out on the same sensor using a different library.
Also don't update the DHT library if you are told there is an update!
As you can tell I had a few problems myself before I got this working, it almost made me disregard the whole project. Keep trying , it's worth it.

[meanmrgreen]

@mikeS thanks alot!
I'll keep that in mind. Should be getting my "starter kit" order soon from eBay so we'll see how it goes ;)

[meanmrgreen]

Finaly got it to compile.
I tried the library link above but no go, cleared out everything about ardouino on the pc, no go.

I finaly stubled onto this:
https://github.com/mysensors/MySensorsArduinoExamples
Downloaded all the expample libraries, loaded the scetch and it worked!

Something is up with the linked library on this page i think

[mfalkvidd]

@meanmrgreen the link pointed to a folder on GitHub. If that folder is downloaded, you get the MySensorsExamples. But in that folder, there is also a link to the original DHT library. If that link is followed, the wrong library will be downloaded.

Several people have been bitten by this so I have now changed the link to point directly to the MySensorsExamples zip file.

[Oli]

Could someone explain me why "Must be >1000ms for DHT22 and >2000ms for DHT11" when sampling rate is once per sec for DHT11 (once per 1000ms) and twice per sec for DHT22 (once per 500ms)?

[Amput]

In Wiring Things Up and screen are used DATA_PIN 3, but in example is wrote #define DHT_DATA_PIN 2 :-) ...please correct it.