💬 Door, Window and Push-button Sensor

[skywatch]

As doors and windows are usually not near power sources would it not be better to have this sketch with a SLEEP function and trigger on interupt?

[Psilin]

what is the logic of the variable "V_TRIPPED"to use? I just messed a little with the MyController application, and by using the V_TRIPPED the value changes from off to on,and stays on,even if the button is released? ( simular to close an opened door)
Should the variable not be of a binary type with according sensor type?

[Slimz]

Hi,
I have my sensor working well, Arduino pro mini with an Ethernet gateway using Home Assistant. .This is the first sensor I'm actually using a battery, so I've never really needed it, I see the battery level in HA as 0, how do I turn that on and use the battery level? Any pointers?
Thanks!
Jim

[Steve Hadley]

Dumb question, but how would I set this sketch to have an array of 5 switches? I’ve tried a couple of things but I’m lost

[Mitja Blazinsek]

https://forum.mysensors.org/topic/7249/simple-binary-switch-example-trying-to-add-second-switch

[rodaman]

Hi,
I rewrite sketch for doors/window/buttons to work with multiple buttons (no rellays) .It shows up in Domoticz but it did not change status buttons if pressed.
Can someone look for the skech what I am doing wrong

/**
  The MySensors Arduino library handles the wireless radio link and protocol
  between your home built sensors/actuators and HA controller of choice.
  The sensors forms a self healing radio network with optional repeaters. Each
  repeater and gateway builds a routing tables in EEPROM which keeps track of the
  network topology allowing messages to be routed to nodes.

  Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
  Copyright (C) 2013-2015 Sensnology AB
  Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors

  Documentation: http://www.mysensors.org
  Support Forum: http://forum.mysensors.org

  This program is free software; you can redistribute it and/or
  modify it under the terms of the GNU General Public License
  version 2 as published by the Free Software Foundation.

*******************************

  DESCRIPTION

  Simple binary switch example updated  for 2 switches
  Connect button or door/window reed switch between
  digitial I/O pin 3 (BUTTON_PIN below) and GND.
  http://www.mysensors.org/build/binary
*/


// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_GATEWAY_SERIAL

//#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define FIRST_PIN  8  // Arduino Digital I/O pin for button/reed switch
#define noButtons 4
const int buttonPin[noButtons];

Bounce debouncer[noButtons] = Bounce();

int oldValue[noButtons];

MyMessage msg[noButtons];

void setup() {

 for (int i = 0; i < noButtons; i++) {

   msg[i].sensor = i;                                   // initialize messages
   msg[i].type = V_TRIPPED; //

   pinMode(buttonPin[i + FIRST_PIN], INPUT_PULLUP);
   digitalWrite(buttonPin[i + FIRST_PIN], HIGH);
   debouncer[i] = Bounce();                        // initialize debouncer
   debouncer[i].attach(buttonPin[i + FIRST_PIN]);
   debouncer[i].interval(30);
 }
}

void presentation() {
 sendSketchInfo("Doors", "1.0");
 for (int i = 0; i < noButtons; i++)
   present(i, S_DOOR);                               // present sensor to gateway


}


//  Check if digital input has changed and send in new value
void loop()
{
 for (int i = 0; i < noButtons; i++) {
   debouncer[i].update();

   int value = debouncer[i].read();
   if (value != oldValue[i]) {

     // Send in the new value
     send(msg[i].set(value == HIGH ? 1 : 0));
     oldValue[i] = value;
   }

 }
}

[mfalkvidd]

@rodaman

I fixed it for you.

[rodaman]

@mfalkvidd
thank you, i hope will be good soul who fix my sketch itself to work... :-)

[hek]

@rodaman said in 💬 Door, Window and Push-button Sensor:

What is the purpose of the buttonPin-array?

E.g.

pinMode(buttonPin[i + FIRST_PIN], INPUT_PULLUP);

This will fetch a random (probably 0-initialised) value from the array and set pinmode on that value...

[rodaman]

@hek
That part was in original sketch for establish internal pullup as I understand. I used array to do it for each pins.

[rodaman]

@hek
I have changed

pinMode(buttonPin[i + FIRST_PIN], INPUT_PULLUP);

to

pinMode(buttonPin[i + FIRST_PIN], INPUT);

thanks, but sadlly still does not work...

[hek]

@rodaman said in 💬 Door, Window and Push-button Sensor:

http://www.mysensors.org/build/binary

I don't get the buttonPin array thing at all?

Why not just:
pinMode(i + FIRST_PIN, INPUT_PULLUP);

[mfalkvidd]

@hek if the array was initialized, it could be used to set arbitrary pins. So pin 4,5,6,7,8,A0,A1,A2,A3 could be used for example (to avoid conflicts with the standard nrf24 wiring but still allow a lot of buttons). But as you mentioned before, without initializing the array the behavior will be strange.

[rodaman]

@hek said in 💬 Door, Window and Push-button Sensor:

pinMode(i + FIRST_PIN, INPUT_PULLUP);

Big Thanks!
I have changed all array parts in setup in the same manner like above and it works :-)

[rodaman]

@rodaman
Hi,
Here is a sketch for multi buttons (no relays, no repeated parts of code for each buttons) just enter number of buttons and first digital pin where buttons are attached.
Thanks to @hek for help...

/**
   The MySensors Arduino library handles the wireless radio link and protocol
   between your home built sensors/actuators and HA controller of choice.
   The sensors forms a self healing radio network with optional repeaters. Each
   repeater and gateway builds a routing tables in EEPROM which keeps track of the
   network topology allowing messages to be routed to nodes.

   Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
   Copyright (C) 2013-2015 Sensnology AB
   Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors

   Documentation: http://www.mysensors.org
   Support Forum: http://forum.mysensors.org

   This program is free software; you can redistribute it and/or
   modify it under the terms of the GNU General Public License
   version 2 as published by the Free Software Foundation.

 *******************************

   DESCRIPTION

   Simple binary switch example updated  for multi switches
   Connect buttons or door/window reed switches between
   digitial I/O choosen pin  (FIRST_PIN below) and GND.
   http://www.mysensors.org/build/binary
*/


// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_GATEWAY_SERIAL

//#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define FIRST_PIN  2  // Arduino Digital I/O pin for button/reed switch
#define noButtons 6


Bounce debouncer[noButtons] = Bounce();

int oldValue[noButtons];
int value;
MyMessage msg[noButtons];

void setup() {

  for (int i = 0; i < noButtons; i++) {

    oldValue[i] = -1;
    
    msg[i].sensor = i;                                   // initialize messages
    msg[i].type = V_TRIPPED; //
    pinMode(i + FIRST_PIN, INPUT_PULLUP);
    digitalWrite(i + FIRST_PIN, HIGH);
  
    debouncer[i] = Bounce();                        // initialize debouncer
    debouncer[i].attach(i + FIRST_PIN);
    debouncer[i].interval(3);
  }
}

void presentation() {
  sendSketchInfo("Doors", "1.0");
  for (int i = 0; i < noButtons; i++)
    present(i, S_DOOR);                               // present sensor to gateway
}


//  Check if digital input has changed and send in new value
void loop()
{
  for (int i = 0; i < noButtons; i++) {
    debouncer[i].update();

    value = debouncer[i].read();
    if (value != oldValue[i]) {
    // Send in the new value
      send(msg[i].set(value == HIGH ? 1 : 0));
      oldValue[i] = value;
    }
 }
}

[gohan]

Could these reed switches be used in the NC configuration for door/window sensor to save more battery?

[scalz]

@gohan
yes exactly.
i made a nrf5 board using this principle.

[gohan]

did you use those with 3 pins?

[scalz]

yes no-nc reed, connect them to IOs of your mcu and switch between input and output

[Nca78]

@gohan said in 💬 Door, Window and Push-button Sensor:

did you use those with 3 pins?

I use them, with one wire connected to each interrupt pin (I only activate the one that's not connected) and they work fine.
Else you can cheat with a basic reed switch, you just need an additional magnet on the other side of your switch that's weaker than the door magnet, and turn your reed 180°.
You make the weak magnet close the reed when door is opened and far from the strong door magnet. When you close the door the strong magnet will open the reed switch.