Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Automated folding blinds

EmielA last edited by

I did a project to automate my folding blinds and used MySensors in combination with Pimatic.
The blinds are driven by a servo motor and controlled by a end microswitch and a Hall sensor. And it has the posibility to open and close by a local touch sensor switch.
I used a DIY folding blind set and modified it with two gears and mounted the servo on it and the switches.
Reply Quote 1
1 Reply Last reply

1
Posts

894
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73900
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

2

2
Votes

2
Posts

35
Views

@Kokosnoot good solution. I remember the discussion in the early days of MySensors. I've powered the radio's for most of my sensors from the 3.3v regulator on the arduino board and for me that works perfect. But for my latest designs I decided to add a separate ams regulator for my radio's like the guys suggested in the beginning. Because you basically want the on board regulator to power the mcu only.
A low cost energy meter
My Project • • OldSurferDude

7

1
Votes

7
Posts

44
Views

@OldSurferDude yes, you are correct. this sensor is capable of 50A continuous, which safely I would make it working at 40A max., but for such an important load as in your case I would go for a beefier one, like the ACS75x, 77x, but at this point I would also change the node's form factor for space and insulation reasons. On my application on the RV I have a max. curr. of 13A running on a AWG14-16 cable (European rules for RVs), so I did not ask myself too many questions beside, of course, safety. About the signal, it will be a sinusoidal signal swinging around Vcc/2. Vcc can be easily measured internally on the ATmega328. On all my DC sensors I measure Vcc at every loop, just before measuring the ADCs. Honestly, when the space is not an issue like in my RV, I would rather use a ring core current transformer, and I would get rid of noise, response time, power dissipation, but over all no need to cut any cable. Long story short, it has been a nice experiment and I used it for 6 months, and then I switched back to my RF-NANO based RS485-Modbus - Mysensors bridge connected to an off-the shelf power analyzer. Just for fun I attach a pic of my 12Vdc sensors installed on my RV. Forgive me for the spaghetti wiring on the right side, but this is an area that needs improvement.
nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

44

18
Votes

44
Posts

8024
Views

The output of the display could also be sent over serial, but the whole idea is you can walk around with the doctor and improve your results as you go.
Halloween Lights
My Project • led strip light ws2812b • • KevinT

1

3
Votes

1
Posts

24
Views

No one has replied

Automated folding blinds

Suggested Topics

Welcome
Announcements • • hek

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

A low cost energy meter
My Project • • OldSurferDude

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Halloween Lights
My Project • led strip light ws2812b • • KevinT

52
Online

11.4k
Users

11.1k
Topics

112.6k
Posts

Automated folding blinds

Suggested Topics

Welcome Announcements • • hek

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

Powering ESP8266 / NRF24L01 repeater through USB (improvement) My Project • • Kokosnoot

A low cost energy meter My Project • • OldSurferDude

nRF24Doctor My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Halloween Lights My Project • led strip light ws2812b • • KevinT

52Online

11.4kUsers

11.1kTopics

112.6kPosts

Welcome
Announcements • • hek

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

A low cost energy meter
My Project • • OldSurferDude

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Halloween Lights
My Project • led strip light ws2812b • • KevinT

52
Online

11.4k
Users

11.1k
Topics

112.6k
Posts