Ping Pong with ESP8266 results in !TSM:FPAR:NO REPLY [solved]

mpp

@gohan thanks for the feedback. According to that page it seems you not only need a gateway but also a controller. This explains why my nodes don't get a node id automatically.

gohan

The controller is needed for auto ID, but it can also be used myscontroller. It is also written in different places that manual id should be set also in case of problems.

mpp

@gohan indeed you're right. What did you mean with "myscontroller"?

Setting the node id manually for the ping pong sketch makes them communicate to the Gateway:

#define MY_NODE_ID 201

Would auto ID work with the ESP MQTT Gateway and OpenHab controller?

I have an MQTT server up and running and OpenHab is installed with the following configuration in /etc/openhab2/services/mqtt.cfg:

broker.url=tcp://127.0.0.1:1883
broker.clientId=OpenHab
broker.retain=true
broker.async=false

Yet I still get !TSM:FPAR:NO REPLY

gohan

https://forum.mysensors.org/topic/838/windows-gui-controller-for-mysensors

I'd start from the ethernet gateway and work it out from there, myscontroller works with ethernet gateway. In openhab I don't know how to enable auto id, but there must be something in documentation. To be honest assigning manually ID has to be done only once because it is saved in eeprom and read at every boot, so I don't see it so mandatory to have the controller handling it.

mpp

@gohan, do you mean http://www.mycontroller.org? I can't find any project page with downloads on the link you provided. There is a download link to a zip file somewhere in the comments but impossible to say if that is still up to date as it dates from 2015.

gohan

yes, it's the zip file. It is a windows app. Mycontroller it is actually a controller like Domoticz or Openhab. I know it is a little old, but it works.

mpp

@gohan, I switched over to mycontroller (from OpenHab) and I'm using Arduino's nodes and I'm still getting errors not finding the parent.

I'm using the Mock sketch and tested with setting the ID manually but no luck.

0 MCO:BGN:INIT NODE,CP=RRNNA--,VER=2.1.1
4 TSM:INIT
4 TSF:WUR:MS=0
108 TSM:INIT:TSP OK
110 TSM:INIT:STATID=99
112 TSF:SID:OK,ID=99
114 TSM:FPAR
3241 TSF:MSG:SEND,99-99-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
5249 !TSM:FPAR:NO REPLY
5251 TSM:FPAR
8378 TSF:MSG:SEND,99-99-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
10385 !TSM:FPAR:NO REPLY
10387 TSM:FPAR
13514 TSF:MSG:SEND,99-99-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
15521 !TSM:FPAR:NO REPLY
15523 TSM:FPAR

Edit: adding a 4.7 capacitor didn't change this. Neither did downgrading to 2.0.

Starting sensor (RRNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=254)
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=254)
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=254)
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 254-254-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:

Any idea?

gohan

On the gateway do you see any message received? Can you post the gateway log when nodes are registering?

mpp

@gohan, when using the WemosD1 (without capacitor!) and a static ID, I get the following:

0;255;3;0;9;TSF:MSG:READ,253-253-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSF:MSG:BC
0;255;3;0;9;TSF:MSG:FPAR REQ,ID=253
0;255;3;0;9;TSF:PNG:SEND,TO=0
0;255;3;0;9;TSF:CKU:OK
0;255;3;0;9;TSF:MSG:GWL OK
0;255;3;0;9;TSF:MSG:SEND,0-0-253-253,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
0;255;3;0;9;TSF:MSG:READ,253-253-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
0;255;3;0;9;TSF:MSG:PINGED,ID=253,HP=1
0;255;3;0;9;TSF:MSG:SEND,0-0-253-253,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
0;255;3;0;9;TSF:MSG:READ,253-253-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
0;255;3;0;9;TSF:MSG:SEND,0-0-253-253,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
0;255;3;0;9;TSF:MSG:READ,253-253-0,s=255,c=0,t=17,pt=0,l=5,sg=0:2.1.1
0;255;3;0;9;Sending message on topic: mpp-mygateway1-out/253/255/0/0/17

When I do the same for the Pro Mini, there is nothing to see. When I flash a Moteino test sketch it works properly.

gohan

@mpp the gateway is getting the message and it replies so you could either have a power issue on gateway or range problem. How far are the gw and node?

mpp

@gohan tested with less than a meter up to 10 meters. In fact the Wemos Node now is working as it shows up in mycontroller but the Pro Mini doesn't receive a response from the GW.

gohan

Do you have other radio modules to try? If not, if you swap the radios do you see any changes? Are the radio rfm69 right?

mpp

@gohan I have several RFM69 radio's and they're all working (with the Moteino sketch) on a Pro Mini.

Here's my config:

#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RF69_433MHZ
#define MY_IS_RFM69HW
#define MY_RF69_IRQ_PIN 4
#define MY_RF69_IRQ_NUM MY_RF69_IRQ_PIN
#define MY_RF69_SPI_CS 15
#define MY_RFM69_NETWORKID 99
#define MY_NODE_ID 123

mpp

Removing some of the config lines seems to have an effect:

0 MCO:BGN:INIT NODE,CP=RRNNA--,VER=2.1.1
4 TSM:INIT
4 TSF:WUR:MS=0
8 TSM:INIT:TSP OK
10 TSF:SID:OK,ID=254
12 TSM:FPAR
143 TSF:MSG:SEND,254-254-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
1232 TSF:MSG:READ,0-0-254,s=255,c=3,t=8,pt=1,l=1,sg=0:0
1239 TSF:MSG:FPAR OK,ID=0,D=1
2150 TSM:FPAR:OK
2150 TSM:ID
2152 TSM:ID:OK
2154 TSM:UPL
2285 !TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=NACK:1
2314 TSF:MSG:READ,0-0-254,s=255,c=3,t=8,pt=1,l=1,sg=0:0
2320 !TSF:MSG:LEN,0!=8
2435 TSF:MSG:READ,0-0-254,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2441 TSF:MSG:PONG RECV,HP=1
2443 TSM:UPL:OK
2445 TSM:READY:ID=254,PAR=0,DIS=1
2580 !TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=NACK:0100
2717 TSF:MSG:READ,0-0-254,s=255,c=3,t=0,pt=1,l=1,sg=0:1
2723 !TSF:MSG:LEN,0!=8
2795 TSF:MSG:READ,0-0-254,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2936 !TSF:MSG:SEND,254-254-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=1,st=NACK:2.1.1
3076 !TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=2,st=NACK:0
3110 TSF:MSG:READ,0-0-254,s=255,c=3,t=0,pt=6,l=2,sg=0:0100
3117 !TSF:MSG:LEN,0!=9
Send Sketch Info: 5197 TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=11,pt=0,l=14,sg=0,ft=3,st=OK:MockMySensors 
5341 !TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=12,pt=0,l=4,sg=0,ft=0,st=NACK:v0.5
MockMySensors v0.5
5480 TSF:MSG:READ,0-0-254,s=255,c=3,t=0,pt=6,l=2,sg=0:0100
5486 !TSF:MSG:LEN,0!=9
Get Config: Metric
Presenting Nodes
________________
  S_DOOR
6375 TSF:MSG:SEND,254-254-0-0,s=1,c=0,t=0,pt=0,l=12,sg=0,ft=1,st=OK:Outside Door
________________
6434 MCO:REG:REQ
6567 !TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=NACK:2
6664 TSF:MSG:READ,0-0-254,s=255,c=3,t=0,pt=6,l=2,sg=0:0100
6670 !TSF:MSG:LEN,0!=9
6744 TSF:MSG:READ,0-0-254,s=255,c=3,t=27,pt=1,l=1,sg=0:1
6750 MCO:PIM:NODE REG=1
6752 MCO:BGN:STP
GW Started
7254 MCO:BGN:INIT OK,TSP=1



#########################
RandomNumber:36
Send Battery Level
7290 TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=1,st=OK:36
Request Time
7929 !TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=1,pt=0,l=0,sg=0,ft=0,st=NACK:
Door is: Open
8509 TSF:MSG:SEND,254-254-0-0,s=1,c=1,t=16,pt=2,l=2,sg=0,ft=1,st=OK:1
System is: Armed
8646 !TSF:MSG:SEND,254-254-0-0,s=1,c=1,t=15,pt=1,l=1,sg=0,ft=0,st=NACK:1
8783 !TSF:MSG:SEND,254-254-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=1,st=NACK:36
8792 TSF:MSG:READ,0-0-254,s=255,c=3,t=27,pt=1,l=1,sg=0:1
8798 !TSF:MSG:LEN,0!=8
#########################

So now the node is sending data but there's no ack/Invalid message length.

gohan

Are they RFM69HW? What antenna are you using on them?

mpp

@gohan they're all HW, yes. I tested with single wire and coil antenna's. Atm I'm testing with authentic Moteino's with single wire. They all result in !TSM:FPAR:FAIL.

Omemanti

@mpp said in Ping Pong with ESP8266 results in !TSM:FPAR:NO REPLY [solved]:

So now the node is sending data but there's no ack/Invalid message length..

@gohan they're all HW, yes. I tested with single wire and coil antenna's. Atm I'm testing with authentic Moteino's with single wire. They all result in !TSM:FPAR:FAIL.

Any progress on this front? I got the exact same things as the log you posted; loads of NACK's.
Checked/replaced radios, antennes and caps ..

Ping Pong with ESP8266 results in !TSM:FPAR:NO REPLY [solved]

21

11.7k

11.2k

113.1k