Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

New Sensor Domoticz

arduino_89_89 13 Jul 2017, 13:36 last edited by

Hi everyone, I have two sensors I can not configure them in Domoticz.
Mq2 gpl and rain sensor Mhrd. How can I do?
Reply Quote 0
1 Reply Last reply 13 Jul 2017, 13:56
Loading More Posts
3
Posts

1.0k
Views
Reply

Reply as topic
Log in to reply
mfalkvidd Mod 13 Jul 2017, 13:56 last edited by @arduino_89_89

@arduino_89_89 welcome to the MySensors community.

What did you do and what were the results?
Reply Quote 0
1 Reply Last reply
arduino_89_89 13 Jul 2017, 13:59 last edited by

I followed the Mq2 Sensor Tutorial, but I'm only out of the kids and not on devices. Instead, for the rain sensor I did not find anything.
Reply Quote 0
1 Reply Last reply

3
Posts

1.0k
Views

Log in to reply

1 out of 3

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • 29 Mar 2014, 17:08 • hek 29 Mar 2014, 17:08

1

0
Votes

1
Posts

3.3k
Views

No one has replied
PJON and Minicore not working
Development • 21 Mar 2025, 19:51 • Trand 21 Mar 2025, 19:51

1

0
Votes

1
Posts

12
Views

No one has replied
Gateway without a radio
Development • 12 Jan 2025, 23:19 • OldSurferDude 14 Jan 2025, 22:07

3

0
Votes

3
Posts

28
Views

14 Jan 2025, 22:07

@OldSurferDude yes, just run the configure command with --my-transport=none
Sending offset to node
Development • 31 Jan 2025, 00:59 • bsl88k 4 Feb 2025, 12:14

3

0
Votes

3
Posts

41
Views

4 Feb 2025, 12:14

Thanks for the idea, i will look into it soon, will let know how it goes..
Radio waking up for no reason.
Development • 4 Jul 2020, 21:09 • Sasquatch 15 Jan 2025, 08:33

3

0
Votes

3
Posts

37
Views

15 Jan 2025, 08:33

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Saving last known good state, but not in EEPROM
Development • 30 Jan 2024, 18:46 • OldSurferDude 15 Jan 2025, 08:51

6

0
Votes

6
Posts

33
Views

15 Jan 2025, 08:51

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?

9
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1