What did you build today (Pictures) ?

[sundberg84]

@tbowmo well I have Domoticz to collect data. Maybe your alternative is much better but I can't change from Domoticz without redo everything. The push is just to get a heads-up how often or changes but I can go into Domoticz and follow 15 min updates as well on a daily, weekly and monthly graph .

[gohan]

@tbowmo as the temperature doesn't change that quickly, the 5 minutes Domoticz interval it is OK. As soon as you see a daily variance within your requirements, you are good

[dbemowsk]

Was I right to assume that the push of temperature changes to the phone every degree was simply for the initial testing to see quickly how often it would change?

[nagelc]

I finally got a BT832 (NRF52832 from Fanstel) to talk to my NRF24 gateway. I got the NFR5s a while ago. Made a quick breakout board (quick to design, but slow delivery). In the mean time, I configured a STM32 "Blue Pill" as a Blackmagic Probe to program it. I had to get the latest Sandeep Mistry NRF5 files from github in order for it to support the blackmagic probe, but . . . it worked : ) So far I have just run the MockMySensors and it shows up on Domoticz.

[tbowmo]

@sundberg84
With a little bit of nodered injected in the stream, you could have domoticz running without ever noticing that influx etc is getting the data as well :)

[sundberg84]

6.3 days or 152hours just inst good enough - this is what my logger managed to do with 2xAA debugging a temp/hum node sending every 15min. Its below 50% to target (14 days) but this included the leds was on all the time... how much can a 2x leds do :neutral_face: ?? Next experiemtn...

[nagelc]

@sundberg84
@tbowmo
Domoticz can also push the data to influx DB. See Settings>More Options>Data Push

[dbemowsk]

So for a few days now I have been working on my idea for a homebrew CNC machine made from mostly salvaged parts. This weekend I made some good progress getting the Y axis drive assembly mostly done. I have not tested anything yet, but I hope to in the next few days. Anyways, here is what I have...

The stepper motor is one salvaged from an old dot matrix printer. The gear on it was press fit on the shaft with no real way to get it off, so I opted to make a geared drive assembly. I realize that this will slow the Y axis down, but it should also give it a bit more precision. Below is the stepper motor.

For mounting it, I designed this adapter plate which carries a steel roller bearing for the screw shaft.

This is an early mounting plate design before I added the upper and lower mounting tabs. This shows the gear with the shaft attached. The gear was made using an OpenSCAD gear library.

Yesterday I designed the bracket that attaches to and drives the Y axis platter/build plate (Sorry, forgot to take a decent pic of that part).

Today I was able to finish the front and rear frame braces and got parts rough fitted together. the 2 rails with the small white linear bearings are some rods that were salvaged from a couple old scanners. These were used as the rail for the scanner head. I have pics of the full assembly as well as the motor assembly mounted on the rear brace.

I can't say how well the design will work, if at all, but it has been a fun journey so far trying.

[boozz]

@dbemowsk
Well it looks as if your 3D-printer works fine :grinning:

What I would be slightly worried about is if with the given size of the rods the stiffness of the structure would be enough.
Hope to see more from this project in the near future.
Good luck!

[dbemowsk]

@boozz I will be curious to see if I can get enough precision to do PCBs. I have yet to buy a GRBL board to control it. For now I am going to use the UNO that I have for testing just to do test runs of the servos until I get one. This is the one I have been looking at:
https://www.ebay.com/itm/Arduino-CNC-Shield-Kit-UNO-Board-4x-DRV8825-Drivers-Package-Deal-FREE-USA-SHIP/292174947187?hash=item4406fbe373:g:A0sAAOSwJThZpeKr
I will also have to figure out the gear ratios of the motor assemblies once I am done because I am sure I will need them to calibrate the GRBL setup. I know on this part of it I have about a 4.8:1 ratio from the motor to the large gear, but I'll have to figure out steps per cm or steps per mm or something. If anyone knows a good way of figuring this out I am all ears.

Thanks for the upvotes.

[NeverDie]

@dbemowsk It will save you the hassle of upgrading if you buy a control board with GRBL1.1f already built in.

[Yveaux]

@dbemowsk said in What did you build today (Pictures) ?:

If anyone knows a good way of figuring this out I am all ears.

It would expect making a large movement using a defined number of steps, and measuring the actual distance moved with a caliper will give you a rather accurate steps/mm.
However, I hope this ratio is constant over the whole range, given the 3d printed gears and expected backlash...

[dbemowsk]

@yveaux as far as the backlash, i had already thought of that. I have 2 coupler nuts with a spring in between to handle the little bit of backlash that there is. I only had a thin spring though. I want to find a stronger one.

[bjacobse]

@sundberg84
Redundancy, maybe you should get a second temp/humidity measurement device, just in case your current beer cooler temp node breaks down...

[mfalkvidd]

@bjacobse or get redundant beer coolers :) Important to always have cool beer.

[bjacobse]

@mfalkvidd
True but usually wines have a higher price and a more valuable - not starting a discussing/flame war what is best to drink...

[dbemowsk]

@mfalkvidd Can't have too much redundancy there...

[NeverDie]

Made this 12 button keypad. Requires only one analog pin to read which button is pressed, and any button press can also wake an arduino from sleep:

Consumes no power when no button is pressed.

[NeverDie]

Here's a thread which covers it in more detail: https://forum.mysensors.org/topic/8936/6-8-buttons-battery-remote-node/36

[rozpruwacz]

@neverdie what happens when you press two or more buttons ??