Why do "passive nodes" need to set their Node ID manually?
-
Well I wanted to filter noise values and I also want to use influx/grafana as a complement to domoticz
-
@smilvert So, do you have the gateway connected directly to Node Red, which then feeds Domoticz and also feeds influx/grafana? I think I want to do the same, if that's how to do it.
-
@NeverDie
Just cut domoticz out of the picture as node-red/influx/grafana works perfect with any gateway serial/ethernet/mqtt.
I prefer the serial gateway in my own experience is the most stable and no reliance on wifi routers and things.
Domoticz has nowhere near the same flexibility when graphing etc. -
@NeverDie
Just cut domoticz out of the picture as node-red/influx/grafana works perfect with any gateway serial/ethernet/mqtt.
I prefer the serial gateway in my own experience is the most stable and no reliance on wifi routers and things.
Domoticz has nowhere near the same flexibility when graphing etc.@rmtucker Ahhhhhh, that's right, it was rmtucker, not toyman, who had done it: https://forum.mysensors.org/topic/6961/nrf5-bluetooth-action/1078
-
@NeverDie @mfalkvidd Passive nodes communicate without message ACKs - ID requests may never make their way to the controller, hence the requirement of a static node ID.
-
@NeverDie @mfalkvidd Passive nodes communicate without message ACKs - ID requests may never make their way to the controller, hence the requirement of a static node ID.
-
I have started to test node-red (Which dont work yet...) so I have created a dummy sketch for parse the data to domoticz.
// Enable debug prints #define MY_DEBUG #define MY_GATEWAY_SERIAL // Enable passive mode #define MY_PASSIVE_NODE #define MY_REPEATER_FEATURE // Passive mode requires static node ID #define MY_NODE_ID 0 // Enable and select radio type attached // #define MY_RADIO_NRF24 //#define MY_RF24_PA_LEVEL RF24_PA_HIGH //#define MY_RADIO_NRF5_ESB //#define MY_RADIO_RFM69 //#define MY_RADIO_RFM95 #include <MySensors.h> #define CHILD_ID_HUM 0 #define CHILD_ID_TEMP 1 #define CHILD_ID_BINARY 2 // Initialize general message MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP); MyMessage msgHum(CHILD_ID_HUM, V_HUM); MyMessage msgBinary(CHILD_ID_BINARY, V_STATUS); int counter = 0; float temperature = 0; float humidity = 0; int binary = 0; void setup() { } void presentation() { // Send the sketch version information to the gateway and controller sendSketchInfo("Passive node", "1.0"); // Register all sensors to gw (they will be created as child devices) present(CHILD_ID_TEMP, S_TEMP); present(CHILD_ID_HUM, S_HUM); present(CHILD_ID_BINARY, S_BINARY); } void loop() { // generate some random data counter ++; if (counter == 20 ){ temperature = 0; humidity = 0; counter = 0; } else { temperature = 25.0 + random(0,30)/10.0; humidity = 55.0 + random(-20,20); } /* if (binary == 0){ send(msgBinary.set(binary,2)); binary = 1; }else { send(msgBinary.set(binary,2)); binary = 0; } */ send(msgTemp.set(temperature,2)); send(msgHum.set(humidity,2)); wait(1000); }@smilvert Got it working: https://www.openhardware.io/view/510/Multi-Sensor-TempHumidityPIR-LeakMagnetLightAccel#tabs-source
I cited you in the credits at the beginning of the sketch.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login