Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

STM32f303k8t6 Nucleo board with DS18S20 Temp sensor.

litunbls last edited by

Dear all, I want to read the temperature by DS18S30. For that i use STM32f303k8t6 Nucleo board.
The Development IDE is Arm Keil v5. Can anyone provide me the library for DS18S30.

Regards
litun
Reply Quote 0
1 Reply Last reply
Yveaux Mod last edited by @litunbls

@litunbls This forum is Arduino only really...
Search the web or convert an Arduino library so it can be compiled in Keil.
Reply Quote 1
1 Reply Last reply

2
Posts

560
Views

Suggested Topics

Air particulate / dust sensor node
My Project • • simbo

2

1
Votes

2
Posts

301
Views

@simbo said in Air particulate / dust sensor node: The PMS7003 module is physically a bit of a pain as the intake / exhaust ports are on the same side as the connector If you are making a PCB you should take that opportunity to put a female header (1.27mm spacing) on it and plug the PMS7003 directly on the PCB: no adapter, no cable needed.
DHT11 sensor with shield LoRa rfm915
My Project • • tahsin_06

2

0
Votes

2
Posts

524
Views

Hi @tahsin_06, welcome to the MySensors community! Did you look at the troubleshooting guide? It shows the most common problems and how to troubleshoot them. Could you post the debug output from your gateway and node?
Washing machine state sensor
My Project • • mvdarend

32

0
Votes

32
Posts

21208
Views

I bought one this year and i am really happy with it.
Slim Node Si7021 sensor example
My Project • • m26872

137

6
Votes

137
Posts

64686
Views

@Eawo Domoticz groups sensors after the order you present them in, see: https://forum.mysensors.org/topic/5132/ds18b20-ans-sht31-d-show-up-as-combined-sensors-on-domoticz/15 I send every 5 minutes and check the value before so that I only send if the value has changed I have been running my sensor for nearly 2 months now and battery level has only decreased 1-2% Make sure you use 1 MHz bootloader
Parking Sensor Node
My Project • • Boots33

5

3
Votes

5
Posts

2696
Views

Updated the sketch for MySensors V2 and am now using the Adafruit Neopixel library /** ******************************* * * DESCRIPTION * A node to indicate correct parking position to allow closing of garage door. * uses a pre built IR beam "door minder" to detect car position *MySensors V2 and using Adafruit neopixel library and bounce2 library * Connect N/O contacts of Infrared device between * pin 3 and GND. * * Connect a N/O reed switch between GND and pin 2 * * Connect RGB Led strip data terminal to pin 4 * */ // Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 #include "MySensors.h" #include <SPI.h> #include <Bounce2.h> #include <Adafruit_NeoPixel.h> #define NUM_LEDS 18 // How many leds are in the strip? change this to the number of LEDs in your strip #define PIN 4 // Data pin that led data will be written out over #define CHILD_ID 0 // door switch MySensors id number #define IR_PIN 3 // Arduino Digital I/O pin for infrared device #define DOOR_PIN 2 // pin garage door switch is connected to int marker = 0; // used to decide if LEDs are allowed to turn white int irValue ; // holder for ir state int doorValue ; // holder for garage door state int oldDoorValue=-1; //set to -1 to ensure current door switch status is sent at startup unsigned long startMillis = 0; // holder for the time when garage door first opens unsigned long millisNow = 0; // holder for the current time const long activeTime = 120000; // Time the sensor will stay active after garage door is opened in milliseconds. change this to suit your situation Bounce debouncerA = Bounce(); // Instantiate Bounce object 1.... iR switch Bounce debouncerB = Bounce(); // Instantiate Bounce object 2.... Garage Door switch MyMessage msg(CHILD_ID,V_TRIPPED); // Parameter 1 = number of pixels in strip // Parameter 2 = Arduino pin number (most are valid) // Parameter 3 = pixel type flags, add together as needed: // NEO_KHZ800 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs) // NEO_KHZ400 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers) // NEO_GRB Pixels are wired for GRB bitstream (most NeoPixel products) // NEO_RGB Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2) Adafruit_NeoPixel strip = Adafruit_NeoPixel(NUM_LEDS, PIN, NEO_GRB + NEO_KHZ800); void setup() { /* ----Setup the buttons as inputs and activate their internal pull-up resistor---- */ pinMode(IR_PIN,INPUT_PULLUP); //set pin as input and activate internal pull-up resistor pinMode(DOOR_PIN,INPUT_PULLUP); //set pin as input and activate internal pull-up resistor /* ---After setting up the buttons, setup debouncers---- */ debouncerA.attach(IR_PIN); debouncerA.interval(5); debouncerB.attach(DOOR_PIN); debouncerB.interval(5); strip.begin(); strip.show(); // Initialize all pixels to 'off' } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Park Sensor", "2.0"); // Register all sensors to gateway (they will be created as child devices) present(CHILD_ID, S_DOOR); // Register binary input sensor to gw } void loop() { updateSwitches(); // call function to check switches status millisNow = millis(); // get the current time if (millisNow - startMillis < activeTime){ // check to see if timeout has been reached if (doorValue == HIGH ) { // garage door is open if (irValue == LOW ) { // car is in ir beam ledChange(strip.Color(255, 0, 0)); // car is blocking ir beam,turn LEDs red } else{ ledChange(strip.Color(0, 255, 0)); // car is out of ir beam, turn LEDs green } } else{ if (marker == 1){ ledChange(strip.Color(127, 127, 127)); // door down but timer not finished. turn leds white for entry mode } } } else { // Timeout has been reached. Turn off LEDs if (marker == 1){ // check marker to only turn off if needed ledChange(strip.Color(0, 0, 0)); // turn off leds (black) marker = 0; } } } /* --------------start of functions-------------- */ /* --Update the switches status, send door state change if required -- */ void updateSwitches (){ debouncerA.update(); // IR switch debouncerB.update(); // Door switch irValue = debouncerA.read(); // get the state of the IR switch doorValue = debouncerB.read(); // get the state of the Door switch if (doorValue != oldDoorValue) { // Check if digital input has changed and send in new value if it has send(msg.set(doorValue==HIGH ? 1 : 0)); // Send in the new value if (doorValue == HIGH){ // door is open startMillis = millis(); // store start time of door opening for timeout check marker = 1; } oldDoorValue = doorValue; } } /* ----------function to change LED color------------*/ void ledChange(uint32_t c) { for(uint16_t i=0; i<strip.numPixels(); i++) { strip.setPixelColor(i, c); } strip.show(); }
My SHT21 and ds18b20 sensor
My Project • ds18b20 sht21 • • Blom

7

4
Votes

7
Posts

5398
Views

Looks great! Would love to see the schematic and 3D print file for the enclosure. @Blom Would you be able to share them?
Slim Node as a Mini 2AA Battery PIR Motion Sensor
My Project • • m26872

36

10
Votes

36
Posts

24517
Views

@Sven-0 Fun to see this old topic again. And also the coincidence, since my visits here have been rare for a long time. Anyway, I'm running a few slimnodes since the beginning and have both good and bad experiences. In general, the battery lifetime is your least concern. Instead I have had issues with sensors, sensitivity, switch contact corrosion, mechanical robustness, wifi interference, repaeter, gateway, controller, waf, kids, animals, etc, etc. Regarding this particular PIR slimnode it's very stable, but it is not universal for every situation due to the limited range and missing sinsitivity adjustment. E.g I can't use it too near my basement windows due to the moving cold air. And in my living room I have sun reflections to deal with. I suggest you start by building a testnode to check if it works for your conditions. A recent PIR-slimnode battery life example; My hallway one died last week after 33 months and around 6000 trips/month.
CDS - Cat Defense System (Arduino + Servo + Motion Sensor)
My Project • • MaKin

8

0
Votes

8
Posts

3824
Views

@MaKin I have not done this build, but if I had to do it I will try with this The most complicated is to find the Raid Power Sprayer