Posts made by frencho

frencho

@tekka could it come from something i setup wrong in the Myconfig.h ?

frencho

@tekka tried what you asked, and some more stuff, still nothing happening

the reboot command send doesn't do anything, the MYSController version is 0.1.2.282

frencho

@tekka I have tried the FDTI with a dummy sketch. I confirm that the RX/TX is working as I change the value of a variable via serial port.

Multiple speed have been tested, from 9600 to 115200.

Looking at the failure tree, I see no other branch to cut down !
Serial com is working
the GW and node seems fine (regarding log)

So why the GW doesn't react when it gets serial messages ?

frencho

@tekka I recompiled everything with the latest Dev Branch, the init problem of the GW is solved.

On GW Side :

06/11/2016 14:56:51	INFO	Connected to COM10
06/11/2016 14:56:52	RX	0;255;3;0;9;MCO:BGN:INIT GW,CP=RRNGA--,VER=2.0.1-beta
06/11/2016 14:56:52	RX	0;255;3;0;9;TSM:INIT
06/11/2016 14:56:52	RX	0;255;3;0;9;TSM:INIT:TSP OK
06/11/2016 14:56:52	RX	0;255;3;0;9;TSM:INIT:GW MODE
06/11/2016 14:56:52	RX	0;255;3;0;9;TSM:READY
06/11/2016 14:56:52	RX	0;255;3;0;14;Gateway startup complete.
06/11/2016 14:56:52	DEBUG	Update child id=255, type=ARDUINO_RELAY
06/11/2016 14:56:52	RX	0;255;0;0;18;2.0.1-beta
06/11/2016 14:56:52	RX	0;255;3;0;9;MCO:REG:NOT NEEDED
06/11/2016 14:56:53	RX	0;255;3;0;9;MCO:BGN:STP
06/11/2016 14:56:53	RX	0;255;3;0;9;MCO:BGN:INIT OK,ID=0,PAR=0,DIS=0,REG=1
06/11/2016 14:57:25	RX	0;255;3;0;9;TSF:MSG:READ,65-65-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
06/11/2016 14:57:25	RX	0;255;3;0;9;TSF:MSG:BC
06/11/2016 14:57:25	RX	0;255;3;0;9;TSF:MSG:FPAR REQ,ID=65
06/11/2016 14:57:25	RX	0;255;3;0;9;TSF:PNG:SEND,TO=0
06/11/2016 14:57:25	RX	0;255;3;0;9;TSF:CKU:OK
06/11/2016 14:57:25	RX	0;255;3;0;9;TSF:MSG:GWL OK
06/11/2016 14:57:25	RX	0;255;3;0;9;TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
06/11/2016 14:57:27	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
06/11/2016 14:57:27	RX	0;255;3;0;9;TSF:MSG:PINGED,ID=65,HP=1
06/11/2016 14:57:27	RX	0;255;3;0;9;TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
06/11/2016 14:57:27	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
06/11/2016 14:57:27	RX	0;255;3;0;9;TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
06/11/2016 14:57:27	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=0,t=18,pt=0,l=10,sg=0:2.0.1-beta
06/11/2016 14:57:27	NODE	New node discovered, node id=65
06/11/2016 14:57:27	CHILD	New child discovered, node id=65, child id=internal
06/11/2016 14:57:27	DEBUG	Update child id=255, type=ARDUINO_RELAY
06/11/2016 14:57:27	RX	65;255;0;0;18;2.0.1-beta
06/11/2016 14:57:27	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
06/11/2016 14:57:27	TX	65;255;3;0;6;M
06/11/2016 14:57:27	RX	65;255;3;0;6;0
06/11/2016 14:57:29	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=11,pt=0,l=5,sg=0:Relay
06/11/2016 14:57:29	RX	65;255;3;0;11;Relay
06/11/2016 14:57:29	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
06/11/2016 14:57:29	RX	65;255;3;0;12;1.0
06/11/2016 14:57:29	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=1,c=0,t=3,pt=0,l=0,sg=0:
06/11/2016 14:57:29	CHILD	New child discovered, node id=65, child id=1
06/11/2016 14:57:29	DEBUG	Update child id=1, type=LIGHT
06/11/2016 14:57:29	RX	65;1;0;0;3;
06/11/2016 14:57:29	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=2,c=0,t=3,pt=0,l=0,sg=0:
06/11/2016 14:57:29	CHILD	New child discovered, node id=65, child id=2
06/11/2016 14:57:29	DEBUG	Update child id=2, type=LIGHT
06/11/2016 14:57:29	RX	65;2;0;0;3;
06/11/2016 14:57:30	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=3,c=0,t=3,pt=0,l=0,sg=0:
06/11/2016 14:57:30	CHILD	New child discovered, node id=65, child id=3
06/11/2016 14:57:30	DEBUG	Update child id=3, type=LIGHT
06/11/2016 14:57:30	RX	65;3;0;0;3;
06/11/2016 14:57:30	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=4,c=0,t=3,pt=0,l=0,sg=0:
06/11/2016 14:57:30	CHILD	New child discovered, node id=65, child id=4
06/11/2016 14:57:30	DEBUG	Update child id=4, type=LIGHT
06/11/2016 14:57:30	RX	65;4;0;0;3;
06/11/2016 14:57:30	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
06/11/2016 14:57:30	RX	0;255;3;0;9;TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
06/11/2016 14:59:38	TX	65;1;1;0;2;
06/11/2016 14:59:43	TX	65;1;1;0;2;1
06/11/2016 14:59:48	TX	65;1;1;1;2;1

on node side :

0 MCO:BGN:INIT REPEATER,CP=RRNRA--,VER=2.0.1-beta
4 MCO:BGN:BFR
6 TSM:INIT
8 TSM:INIT:TSP OK
10 TSF:SID:OK,ID=65
12 TSM:FPAR
145 TSF:MSG:SEND,65-65-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
493 TSF:MSG:READ,0-0-65,s=255,c=3,t=8,pt=1,l=1,sg=0:0
497 TSF:MSG:FPAR OK,ID=0,D=1
2152 TSM:FPAR:OK
2152 TSM:ID
2154 TSM:ID:OK
2156 TSM:UPL
2164 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2183 TSF:MSG:READ,0-0-65,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2189 TSF:MSG:PONG RECV,HP=1
2191 TSM:UPL:OK
2193 TSM:READY
2203 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2326 TSF:MSG:READ,0-0-65,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2385 TSF:MSG:SEND,65-65-0-0,s=255,c=0,t=18,pt=0,l=10,sg=0,ft=0,st=OK:2.0.1-beta
2402 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4419 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=11,pt=0,l=5,sg=0,ft=0,st=OK:Relay
4433 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4450 TSF:MSG:SEND,65-65-0-0,s=1,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4464 TSF:MSG:SEND,65-65-0-0,s=2,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4481 TSF:MSG:SEND,65-65-0-0,s=3,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4495 TSF:MSG:SEND,65-65-0-0,s=4,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4501 MCO:REG:REQ
4511 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4569 TSF:MSG:READ,0-0-65,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4575 MCO:PIM:NODE REG=1
4579 MCO:BGN:STP
4581 MCO:BGN:INIT OK,ID=65,PAR=0,DIS=1,REG=1

The other problem is still here, nothing happen when I try to change state of relay.
I tryed to send the the only Tx message sent during communication between GW and Node

06/11/2016 14:57:27	TX	65;255;3;0;6;M

and nothing

I also noticed every now and then that the Node is forwarding some broadcast message from GW :

477822 TSF:MSG:READ,0-0-255,s=255,c=3,t=20,pt=0,l=0,sg=0:
477831 TSF:MSG:BC
478488 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=21,pt=1,l=1,sg=0,ft=0,st=OK:0
478496 TSF:MSG:FWD BC MSG
478629 TSF:MSG:SEND,0-65-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:

It's got to be a problem bewteen PC/Rasp and GW ... maybe my FDTI ... but I have 2 different !

frencho

@tekka arduino 1.6.11 and AVRISP mkII

It looks like the Tx serial from PC to GW is not working ! when I send a command, I see the Tx from FDTI blinking, ...

I posted other msg on the forum previously, beacause I can't get ride of the fail debug below

03/11/2016 21:12:50 RX  0;255;3;0;9;!TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=NACK:0100

I'll try today to program the gateway from my Mac

frencho

@tekka thanks again. Which two init message are unusual ?

I just tried an other FDTI adapter nothing changed.
The gateway is power via the FDTI/USB !! this thing is driving me crazy !

I'll try also tonight to power GW with 2 AA bat, and read Serial only with the FDTI

I think I'm going to buy a moteino, I hope it will solve my problems.

frencho

@tekka thanks for the analysis !

I have tryied two different GW : one was with gertsanders arduino module, one with a arduino pro mini 3.3V/8Mhz ATM328
they are connected with FTDI to the computer / domotic box
the speed is set to 115200 baud

here is the GW sketch

// Enable debug prints to serial monitor
#define MY_DEBUG


// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL



// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <MySensors.h>

void setup() {
 // Setup locally attached sensors
}

void presentation() {
// Present locally attached sensors
}

void loop() {
 // Send locally attached sensor data here
}

frencho

@tekka

here we go the gateway log

03/11/2016 21:12:31	INFO	Connected to COM12
03/11/2016 21:12:33	RX	0;255;3;0;9;MCO:BGN:INIT GW,CP=RRNGA--,VER=2.0.1-beta
03/11/2016 21:12:33	RX	0;255;3;0;9;TSM:INIT
03/11/2016 21:12:33	RX	0;255;3;0;9;TSM:INIT:TSP OK
03/11/2016 21:12:33	RX	0;255;3;0;9;TSM:INIT:GW MODE
03/11/2016 21:12:33	RX	0;255;3;0;9;TSM:READY
03/11/2016 21:12:33	RX	0;255;3;0;14;Gateway startup complete.
03/11/2016 21:12:33	DEBUG	Update child id=255, type=ARDUINO_RELAY
03/11/2016 21:12:33	RX	0;255;0;0;18;2.0.1-beta
03/11/2016 21:12:33	RX	0;255;3;0;9;MCO:REG:NOT NEEDED
03/11/2016 21:12:33	RX	0;255;3;0;9;MCO:BGN:STP
03/11/2016 21:12:33	RX	0;255;3;0;9;MCO:BGN:INIT OK,ID=0,PAR=0,DIS=0,REG=1
03/11/2016 21:12:48	RX	0;255;3;0;9;TSF:MSG:READ,65-65-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
03/11/2016 21:12:48	RX	0;255;3;0;9;TSF:MSG:BC
03/11/2016 21:12:48	RX	0;255;3;0;9;TSF:MSG:FPAR REQ,ID=65
03/11/2016 21:12:48	RX	0;255;3;0;9;TSF:PNG:SEND,TO=0
03/11/2016 21:12:48	RX	0;255;3;0;9;TSF:CKU:OK
03/11/2016 21:12:48	RX	0;255;3;0;9;TSF:MSG:GWL OK
03/11/2016 21:12:49	RX	0;255;3;0;9;TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
03/11/2016 21:12:50	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
03/11/2016 21:12:50	RX	0;255;3;0;9;TSF:MSG:PINGED,ID=65,HP=1
03/11/2016 21:12:50	RX	0;255;3;0;9;TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
03/11/2016 21:12:50	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
03/11/2016 21:12:50	RX	0;255;3;0;9;!TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=NACK:0100
03/11/2016 21:12:50	RX	0;255;3;0;9;MCO:BGN:INIT GW,CP=RRNGA--,VER=2.0.1-beta
03/11/2016 21:12:50	RX	0;255;3;0;9;TSM:INIT
03/11/2016 21:12:50	RX	0;255;3;0;9;TSM:INIT:TSP OK
03/11/2016 21:12:50	RX	0;255;3;0;9;TSM:INIT:GW MODE
03/11/2016 21:12:50	RX	0;255;3;0;9;TSM:READY
03/11/2016 21:12:50	RX	0;255;3;0;14;Gateway startup complete.
03/11/2016 21:12:50	DEBUG	Update child id=255, type=ARDUINO_RELAY
03/11/2016 21:12:50	RX	0;255;0;0;18;2.0.1-beta
03/11/2016 21:12:50	RX	0;255;3;0;9;MCO:REG:NOT NEEDED
03/11/2016 21:12:50	RX	0;255;3;0;9;MCO:BGN:STP
03/11/2016 21:12:51	RX	0;255;3;0;9;MCO:BGN:INIT OK,ID=0,PAR=0,DIS=0,REG=1
03/11/2016 21:12:51	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
03/11/2016 21:12:51	TX	65;255;3;0;6;M
03/11/2016 21:12:51	RX	65;255;3;0;6;0
03/11/2016 21:12:52	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=11,pt=0,l=5,sg=0:Relay
03/11/2016 21:12:52	RX	65;255;3;0;11;Relay
03/11/2016 21:12:52	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
03/11/2016 21:12:52	RX	65;255;3;0;12;1.0
03/11/2016 21:12:52	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=1,c=0,t=3,pt=0,l=0,sg=0:
03/11/2016 21:12:52	DEBUG	Update child id=1, type=LIGHT
03/11/2016 21:12:52	RX	65;1;0;0;3;
03/11/2016 21:12:53	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=2,c=0,t=3,pt=0,l=0,sg=0:
03/11/2016 21:12:53	DEBUG	Update child id=2, type=LIGHT
03/11/2016 21:12:53	RX	65;2;0;0;3;
03/11/2016 21:12:53	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=3,c=0,t=3,pt=0,l=0,sg=0:
03/11/2016 21:12:53	DEBUG	Update child id=3, type=LIGHT
03/11/2016 21:12:53	RX	65;3;0;0;3;
03/11/2016 21:12:53	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=4,c=0,t=3,pt=0,l=0,sg=0:
03/11/2016 21:12:53	DEBUG	Update child id=4, type=LIGHT
03/11/2016 21:12:53	RX	65;4;0;0;3;
03/11/2016 21:12:53	RX	0;255;3;0;9;TSF:MSG:READ,65-65-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
03/11/2016 21:12:53	RX	0;255;3;0;9;TSF:MSG:SEND,0-0-65-65,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
03/11/2016 21:13:02	TX	65;4;1;1;2;0
03/11/2016 21:13:47	TX	65;3;1;1;2;0
03/11/2016 21:13:52	TX	65;2;1;1;2;0
03/11/2016 21:13:56	TX	65;1;1;1;2;0

If you need anything else ....

I was actually hoping it would be some set up I would have forgotten or some like that !

frencho

Hi ,
I'm trying to make a realy actuator on my system :
Gateway serial working with temp sensor v2 using the standard program provided with the myConfig configured for RFM69

The node with the relay runs the following code :

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <MySensors.h>

#define RELAY_1  3  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 4 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay


void before() { 
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);   
    // Set relay to last known state (using eeprom storage) 
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

void setup() {
  
}

void presentation()  
{   
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay", "1.0");

  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Register all sensors to gw (they will be created as child devices)
    present(sensor, S_BINARY);
  }
}


void loop() 
{
  
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  
     // Change relay state
     digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   
}

The node has the ID 65, when I send via MYScontroller, or my domotic controler (Jeedom) a message to set the relay on/off the node doesn't receive anything

here are the log on node side :

0 MCO:BGN:INIT REPEATER,CP=RRNRA--,VER=2.0.1-beta
4 MCO:BGN:BFR
6 TSM:INIT
8 TSM:INIT:TSP OK
10 TSF:SID:OK,ID=65
12 TSM:FPAR
145 TSF:MSG:SEND,65-65-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
825 TSF:MSG:READ,0-0-65,s=255,c=3,t=8,pt=1,l=1,sg=0:0
831 TSF:MSG:FPAR OK,ID=0,D=1
2152 TSM:FPAR:OK
2152 TSM:ID
2154 TSM:ID:OK
2156 TSM:UPL
2164 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2183 TSF:MSG:READ,0-0-65,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2189 TSF:MSG:PONG RECV,HP=1
2191 TSM:UPL:OK
2193 TSM:READY
2203 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2373 !TSF:MSG:SEND,65-65-0-0,s=255,c=0,t=18,pt=0,l=10,sg=0,ft=0,st=NACK:2.0.1-beta
2390 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=1,st=OK:0
4405 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=11,pt=0,l=5,sg=0,ft=0,st=OK:Relay
4419 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4435 TSF:MSG:SEND,65-65-0-0,s=1,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4450 TSF:MSG:SEND,65-65-0-0,s=2,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4466 TSF:MSG:SEND,65-65-0-0,s=3,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4481 TSF:MSG:SEND,65-65-0-0,s=4,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4487 MCO:REG:REQ
4497 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4554 TSF:MSG:READ,0-0-65,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4560 MCO:PIM:NODE REG=1
4564 MCO:BGN:STP
4567 MCO:BGN:INIT OK,ID=65,PAR=0,DIS=1,REG=1
601131 TSF:MSG:READ,0-0-255,s=255,c=3,t=20,pt=0,l=0,sg=0:
601137 TSF:MSG:BC
601284 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=21,pt=1,l=1,sg=0,ft=0,st=OK:0
601292 TSF:MSG:FWD BC MSG
601425 TSF:MSG:SEND,0-65-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
1199908 TSF:MSG:READ,0-0-255,s=255,c=3,t=20,pt=0,l=0,sg=0:
1199915 TSF:MSG:BC
1200738 TSF:MSG:SEND,65-65-0-0,s=255,c=3,t=21,pt=1,l=1,sg=0,ft=0,st=OK:0
1200746 TSF:MSG:FWD BC MSG
1200879 TSF:MSG:SEND,0-65-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:

The message sent to trun on//off the relay for is for exemple :
65;4;1;1;2;1 or 0

any Idea why the messages is not going threw ?
thanks

frencho

@korttoma if you solved your pb, how did you do it ?

frencho

@TheoL you mean send request registration before init complete ?

But that's the mysensors core which handle all that part, I didn't do anything ?
I'm using the master, and I have been told that there could be a bug. I'll try tonight the dev branch and see if I have the same behavior

frencho

Hi,
I'm having a problem with both RFM69 and NRF24 radio between node and gateway !
First I tried with RFM69, then wanted to check if still had the same FAIL with NRF24 : bingo, same st=fail

On the doc I found about the debug message, I undstand st=Fail means that the gateway doesn't send Ack
I really don't understand how it could be possible that with 2 differents radio type (NRF24 and RFM69) I get the same problem.

does anyone have an idea where this st=fail could come from ?

see below the log on the node side with NRF24 module.
TSP:PING:SEND (dest=0)
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=ok:1
TSP:MSG:READ 0-0-165 s=255,c=3,t=25,pt=1,l=1,sg=0:1
TSP:MSG:PONG RECV (hops=1)
TSP:CHKUPL:OK
TSM:UPL:OK
TSM:READY
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100
!TSP:MSG:SEND 165-165-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=fail:2.0.0
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,ft=1,st=ok:0
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=ok:Temperature Sensor
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=ok:1.1
TSP:MSG:SEND 165-165-0-0 s=0,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=ok:
Request registration...
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=ok:2
TSP:MSG:READ 0-0-165 s=255,c=3,t=27,pt=1,l=1,sg=0:1
Node registration=1
Init complete, id=165, parent=0, distance=1, registration=1

frencho

@hek Thanks hek, it was indeed the problem.

Now I connected the gateway to the Jeedom box, and on the node side I get this :
Starting sensor (RRNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=165)
TSM:FPAR
TSP:MSG:SEND 165-165-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSP:MSG:READ 0-0-165 s=255,c=3,t=8,pt=1,l=1,sg=0:0
TSP:MSG:FPAR RES (ID=0, dist=0)
TSP:MSG:PAR OK (ID=0, dist=1)
TSM:FPAR:OK
TSM:ID
TSM:CHKID:OK (ID=165)
TSM:UPL
TSP:PING:SEND (dest=0)
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=ok:1
TSP:MSG:READ 0-0-165 s=255,c=3,t=25,pt=1,l=1,sg=0:1
TSP:MSG:PONG RECV (hops=1)
TSP:CHKUPL:OK
TSM:UPL:OK
TSM:READY
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100
!TSP:MSG:SEND 165-165-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=fail:2.0.0
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,ft=1,st=ok:0
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=ok:Temperature Sensor
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=ok:1.1
TSP:MSG:SEND 165-165-0-0 s=0,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=ok:
Request registration...
TSP:MSG:SEND 165-165-0-0 s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=ok:2
TSP:MSG:READ 0-0-165 s=255,c=3,t=27,pt=1,l=1,sg=0:1
Node registration=1
Init complete, id=165, parent=0, distance=1, registration=1
TSP:MSG:SEND 165-165-0-0 s=0,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=ok:22.5

I see the gateway led blinking so its receiving the messages but the jeedom box doesn't recognize the node.

!TSP:MSG:SEND 165-165-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=fail:2.0.0
I can't understand what this st=fail means, and if it can be the root of my problem ? any idea please

frencho

@marceloaqno just wondering because I could figure it out looking at your code : does it work with nrf24 And rfm69 or just nrf24?!

Regardless of your answer you did a great job, that awesome thanks

frencho

I just saw that the PR537 was merged
@marceloaqno great job, do you now plan to write some build instructions ? I've had a look at the file, but I don't want to mess it all up

frencho

Hello,
I'm trying to get working my gateway and node with my new RFM69HW. I first tried everything with the gateway and node example from lowpowerlab, it's working like a charm.
The trouble comes when I upload the sketch for Mysensor gateway and a dummy node.

Here is what I get in the com port on the gateway side :
0;255;3;0;9;Starting gateway (RRNGA-, 2.0.0)
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSM:RADIO:OK
0;255;3;0;9;TSM:GW MODE
0;255;3;0;9;TSM:READY
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.0.0
0;255;3;0;9;No registration required
0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1
0;255;3;0;9;TSP:MSG:READ 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSP:MSG:BC
0;255;3;0;9;TSP:MSG:FPAR REQ (sender=255)
0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL)
0;255;3;0;9;TSP:MSG:GWL OK
0;255;3;0;9;TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=bc:0
0;255;3;0;9;TSP:MSG:READ 255-255-0 s=255,c=3,t=3,pt=0,l=0,sg=0:
255;255;3;0;3;
0;255;3;0;9;TSP:MSG:READ 255-255-0 s=255,c=3,t=3,pt=0,l=0,sg=0:
255;255;3;0;3;
0;255;3;0;9;TSP:MSG:READ 255-255-0 s=255,c=3,t=3,pt=0,l=0,sg=0:
255;255;3;0;3;
0;255;3;0;9;TSP:MSG:READ 255-255-0 s=255,c=3,t=3,pt=0,l=0,sg=0:
255;255;3;0;3;

on the node side, I get 4 times
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0, ft=0, st=bc:
TSM:FPAR
... and at the end
!TSM:FPAR:FAIL
!TSM:FAILURE

any idea what all this means ? because on my side i'm stuck with that issue;
thanks guys

frencho

@BenCranston did you get it to work ?

frencho

@Fleischtorte is your code example working ? I mean do you see the RSSI going down to -70 ?
Cause on this page https://lowpowerlab.com/2015/11/11/rfm69_atc-automatic-transmission-control/ Felix says we must use a radio.sendwithretry ?!
I'm a little confused it not working so I'm digging

frencho

@chrille working, the antenna was the problem. I ordered some small antenna on ebay, and it s fine now ^^

frencho

@chrille I'm facing similar behavior with my setup, I get the st:fail but if I touch the antenna on the gateway side, it's working fine.

My setup is arduino 2.0, on the same node as @alexsh1 (the @GertSanders one) with the NRF2RFM69 adapter from @tbowmo. Antenna is wire lenght of 82.2 mm for the 868Mhz rfm69HW.

on the gateway side I did :
// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69

I added a small capacitor on the VCC-GND of the radio, and I soldered the jumper 2 to connect IRQ

the inclusion mode is also fully commented (I don't have inclusion button on board)

and the config file also #define MY_IS_RFM69HW is uncommented as well as #define MY_RADIO_RFM69

Any idea where my st:fail could come from ?