Navigation

    • Register
    • Login
    • OpenHardware.io
    • Categories
    • Recent
    • Tags
    • Popular
    1. Home
    2. Luc3as
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    Luc3as

    @Luc3as

    3
    Reputation
    10
    Posts
    777
    Profile views
    0
    Followers
    0
    Following
    Joined Last Online
    Website lukasporubcan.sk Location Dubnica nad Vahom, Slovakia

    Luc3as Follow

    Best posts made by Luc3as

    • RE: πŸ’¬ Building a Raspberry Pi Gateway

      @Luc3as Okay, Again I found answer while after asking, I used dev branch of mysensors and it is working like a charm.

      posted in Announcements
      Luc3as
      Luc3as
    • RS485 Gateway on Raspberry Pi

      Re: RS485/RS232/Serial transport class for mysensors.org

      Hello gentlemans,
      I am strugling with crazy combination of RS485 adapter connected to Raspberry Pi, which is running Node-RED, and I would like to connect arduino sensors through RS485 to this gateway.
      For start, I hope this configuration is possible. So I connected the MAX RS485 adapter to the pi like this 0_1495647613483_raspberry rs485_bb.png
      I installed the MySensors gateway , and I am able to run it without problem, I can even see gateway started successfully, but I think it doesn't know anything about status of RS485 in real.

      On the other side I burnt example of RS485 motion sensor to arduino pro mini, and watched serial console, It cannot Find parent so there has to be some communication issue.

      I wanted to exclude Raspberry pi as gateway from this so I came with another setup, 2 arduinos with adapters together, one acting as Gateway, second one still with motion sensor example.
      0_1495647860667_pro mini nano RS485_bb.png
      However the results are still the same, Gateway starts without problem, and node is looking for gateway, no presentation, nor sending any data.

      So I was searching through forums and sites day and night, I found some examples of test sketches from altasoft library. With this setup I flashed both and I got working communication, it was sender repeater node so when I wrote something to console it looped me back from another end. Actually I had DE pins connected to D10 as I found it in description.

      When I tried to flash mysensors GW and Node again, can't get any data flowing. I tried to switch DE pins on both D10 and D2 pins as in sketch, I tried to change baudrate, switch roles with GW and Node, twist RX and TX pins, all combinations, nothing.

      Do you guys have any clue what am I doing wrong with vanilla setup like this ?

      Thanks

      EDIT:
      God, why is it , every time I am going to ask about some problem, moments later find solution.
      Wish I found this tread earlier https://forum.mysensors.org/topic/5495/rs485-on-nano/12
      So for future references, With use of RS485 wired network, there must be static node ID set for every node and for gateway too.
      P.S. We should update the documentation, and maybe add wiring picture to the https://www.mysensors.org/build/rs485

      posted in Development
      Luc3as
      Luc3as
    • RE: πŸ’¬ Building a Raspberry Pi Gateway

      do you have SPI enabled through raspi-config ?

      posted in Announcements
      Luc3as
      Luc3as

    Latest posts made by Luc3as

    • [SOLVED] I_version spamming from GW

      Hello, I donΒ΄t know if it is normal behavior, but I have ESP8266 GW with NRF240L , controller is homeassistant where I have version 2.0 in config of component.
      When I connect to GW with MYScontroller, I can see there is a lot of messages about receiving internal version
      Is this coming from HASS, or can I disable it somehow ? or it is completely normal and I should ignore it. thank you

      43	09.09.2017 18:12:22	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      44	09.09.2017 18:12:23	RX	6	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	39627
      45	09.09.2017 18:12:32	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      46	09.09.2017 18:12:42	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      47	09.09.2017 18:12:52	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      48	09.09.2017 18:13:02	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      49	09.09.2017 18:13:09	RX	5 - Weather_Station	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	47248
      50	09.09.2017 18:13:12	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      51	09.09.2017 18:13:22	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      52	09.09.2017 18:13:27	RX	6	0	C_SET	NO	V_TEMP	21.4
      53	09.09.2017 18:13:27	RX	6	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	41032
      54	09.09.2017 18:13:32	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      55	09.09.2017 18:13:42	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      56	09.09.2017 18:13:52	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      57	09.09.2017 18:14:02	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      58	09.09.2017 18:14:11	RX	5 - Weather_Station	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	48818
      59	09.09.2017 18:14:12	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      60	09.09.2017 18:14:22	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      61	09.09.2017 18:14:30	RX	6	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	42430
      62	09.09.2017 18:14:32	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      63	09.09.2017 18:14:42	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      64	09.09.2017 18:14:53	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      65	09.09.2017 18:15:02	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      66	09.09.2017 18:15:12	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      67	09.09.2017 18:15:14	RX	5 - Weather_Station	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	50391
      68	09.09.2017 18:15:22	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      69	09.09.2017 18:15:32	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      70	09.09.2017 18:15:34	RX	6	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	43829
      71	09.09.2017 18:15:42	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      72	09.09.2017 18:15:52	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      73	09.09.2017 18:16:02	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      74	09.09.2017 18:16:12	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      75	09.09.2017 18:16:15	RX	5 - Weather_Station	5 - S_MULTIMETER	C_SET	NO	V_VOLTAGE	3.58
      76	09.09.2017 18:16:17	RX	5 - Weather_Station	2 - S_BARO	C_SET	NO	V_PRESSURE	1001.7
      77	09.09.2017 18:16:17	RX	5 - Weather_Station	2 - S_BARO	C_SET	NO	V_UNIT_PREFIX	hPa
      78	09.09.2017 18:16:17	RX	5 - Weather_Station	6 - S_MOISTURE	C_SET	NO	V_LEVEL	61.0
      79	09.09.2017 18:16:17	RX	5 - Weather_Station	6 - S_MOISTURE	C_SET	NO	V_UNIT_PREFIX	%
      80	09.09.2017 18:16:18	RX	5 - Weather_Station	1 - S_TEMP	C_SET	NO	V_TEMP	22.3
      81	09.09.2017 18:16:18	RX	5 - Weather_Station	0 - S_HUM	C_SET	NO	V_HUM	65
      82	09.09.2017 18:16:18	RX	5 - Weather_Station	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	53594
      83	09.09.2017 18:16:22	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      84	09.09.2017 18:16:32	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      85	09.09.2017 18:16:37	RX	6	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	45226
      86	09.09.2017 18:16:42	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      87	09.09.2017 18:16:52	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      88	09.09.2017 18:17:02	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      89	09.09.2017 18:17:12	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      90	09.09.2017 18:17:21	RX	5 - Weather_Station	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	55167
      91	09.09.2017 18:17:22	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      92	09.09.2017 18:17:32	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      93	09.09.2017 18:17:41	RX	6	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	46623
      94	09.09.2017 18:17:43	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      95	09.09.2017 18:17:52	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      96	09.09.2017 18:18:03	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      97	09.09.2017 18:18:12	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      98	09.09.2017 18:18:23	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      99	09.09.2017 18:18:23	RX	5 - Weather_Station	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	56736
      100	09.09.2017 18:18:33	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      101	09.09.2017 18:18:42	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      102	09.09.2017 18:18:44	RX	6	INTERNAL	C_INTERNAL	NO	I_HEARTBEAT_RESPONSE	48019
      103	09.09.2017 18:18:53	RX	0 - Gateway	INTERNAL	C_INTERNAL	NO	I_VERSION	2.1.1
      
      
      posted in Home Assistant
      Luc3as
      Luc3as
    • RE: πŸ’¬ Building a Raspberry Pi Gateway

      do you have SPI enabled through raspi-config ?

      posted in Announcements
      Luc3as
      Luc3as
    • RE: MySensors weather station

      @dbemowsk yup, actually there are 8 of them, each providing nominal 0,5 volts, so to power up the lipo charger for battery I need at least 4 volts, in direct sunlight I think this will not be problem, but as @dbemowsk says, it will not have ideal position to sun every day and for whole time. but there is big enough reserve at battery , providing power for few days to weeks even without solar panel.
      and I am also checking voltage on solar panel so if there would be some problem with charging I can set notifications or something from home automation system.

      posted in Enclosures / 3D Printing
      Luc3as
      Luc3as
    • RE: πŸ’¬ Building a Raspberry Pi Gateway

      @Luc3as Okay, Again I found answer while after asking, I used dev branch of mysensors and it is working like a charm.

      posted in Announcements
      Luc3as
      Luc3as
    • RE: MySensors weather station

      Hello all,
      I'd like to add to this discussion my bit,
      here is code from my older project of arduino based, battery operated, solar panel charged weather station
      https://github.com/Luc3as/MySensors-WeatherStation
      I must finish all documentation, I have PCBs ready and manufactured and tested, and models ready for 3d prints too.
      I am not measuring wind so I am also interested in nice work above.
      for now it is still work in progress, here is little teaser of overall look
      0_1495694816412_IMG_20170519_171638.jpg

      posted in Enclosures / 3D Printing
      Luc3as
      Luc3as
    • RE: πŸ’¬ Building a Raspberry Pi Gateway

      Hello, did anyone tried gateway on pi with RS485 wired network ? It looks like node with ID set is looking for parrent and gateway does not respond to the node and therefore there is no succesfull presentation.
      example from GW mysgw:

      TSF:MSG:SEND,0-0-5-5,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
      mysgw: TSF:MSG:READ,5-5-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
      mysgw: TSF:MSG:BC
      mysgw: TSF:MSG:FPAR REQ,ID=5
      mysgw: TSF:PNG:SEND,TO=0
      mysgw: TSF:CKU:OK
      mysgw: TSF:MSG:GWL OK
      mysgw: TSF:MSG:SEND,0-0-5-5,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
      mysgw: TSF:MSG:READ,5-5-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
      mysgw: TSF:MSG:BC
      mysgw: TSF:MSG:FPAR REQ,ID=5
      mysgw: TSF:CKU:OK,FCTRL
      mysgw: TSF:MSG:GWL OK
      mysgw: TSF:MSG:SEND,0-0-5-5,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
      mysgw: TSF:MSG:READ,5-5-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
      mysgw: TSF:MSG:BC
      mysgw: TSF:MSG:FPAR REQ,ID=5
      mysgw: TSF:CKU:OK,FCTRL
      mysgw: TSF:MSG:GWL OK
      mysgw: TSF:MSG:SEND,0-0-5-5,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
      mysgw: TSF:MSG:READ,5-5-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
      mysgw: TSF:MSG:BC
      mysgw: TSF:MSG:FPAR REQ,ID=5
      mysgw: TSF:CKU:OK,FCTRL
      mysgw: TSF:MSG:GWL OK
      mysgw: TSF:MSG:SEND,0-0-5-5,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
      

      and from node :

      0 MCO:BGN:INIT NODE,CP=RSNNA--,VER=2.1.1
      3 TSM:INIT
      4 TSF:WUR:MS=0
      5 TSM:INIT:TSP OK
      7 TSM:INIT:STATID=5
      9 TSF:SID:OK,ID=5
      10 TSM:FPAR
      27 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      2035 !TSM:FPAR:NO REPLY
      2037 TSM:FPAR
      2055 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      4063 !TSM:FPAR:NO REPLY
      4065 TSM:FPAR
      4082 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      6090 !TSM:FPAR:NO REPLY
      6092 TSM:FPAR
      6110 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
      8118 !TSM:FPAR:FAIL
      8119 TSM:FAIL:CNT=1
      
      posted in Announcements
      Luc3as
      Luc3as
    • RS485 Gateway on Raspberry Pi

      Re: RS485/RS232/Serial transport class for mysensors.org

      Hello gentlemans,
      I am strugling with crazy combination of RS485 adapter connected to Raspberry Pi, which is running Node-RED, and I would like to connect arduino sensors through RS485 to this gateway.
      For start, I hope this configuration is possible. So I connected the MAX RS485 adapter to the pi like this 0_1495647613483_raspberry rs485_bb.png
      I installed the MySensors gateway , and I am able to run it without problem, I can even see gateway started successfully, but I think it doesn't know anything about status of RS485 in real.

      On the other side I burnt example of RS485 motion sensor to arduino pro mini, and watched serial console, It cannot Find parent so there has to be some communication issue.

      I wanted to exclude Raspberry pi as gateway from this so I came with another setup, 2 arduinos with adapters together, one acting as Gateway, second one still with motion sensor example.
      0_1495647860667_pro mini nano RS485_bb.png
      However the results are still the same, Gateway starts without problem, and node is looking for gateway, no presentation, nor sending any data.

      So I was searching through forums and sites day and night, I found some examples of test sketches from altasoft library. With this setup I flashed both and I got working communication, it was sender repeater node so when I wrote something to console it looped me back from another end. Actually I had DE pins connected to D10 as I found it in description.

      When I tried to flash mysensors GW and Node again, can't get any data flowing. I tried to switch DE pins on both D10 and D2 pins as in sketch, I tried to change baudrate, switch roles with GW and Node, twist RX and TX pins, all combinations, nothing.

      Do you guys have any clue what am I doing wrong with vanilla setup like this ?

      Thanks

      EDIT:
      God, why is it , every time I am going to ask about some problem, moments later find solution.
      Wish I found this tread earlier https://forum.mysensors.org/topic/5495/rs485-on-nano/12
      So for future references, With use of RS485 wired network, there must be static node ID set for every node and for gateway too.
      P.S. We should update the documentation, and maybe add wiring picture to the https://www.mysensors.org/build/rs485

      posted in Development
      Luc3as
      Luc3as
    • RE: πŸ’¬ Atmospheric Pressure Sensor

      I tried to modify the weather forecast script to run each 5 minutes instead of every minute but now I am getting strange forecasts and sometimes unknown conditions.
      Doesn't anybody tried to accomplish this ?

      posted in Announcements
      Luc3as
      Luc3as
    • fail presentation

      hello I am using latest Home Assistant with mysensors installed and I am getting this strange error in log after connecting humidity sensor node

       INFO:requests.packages.urllib3.connectionpool:Starting new HTTP connection (1): 192.168.1.10
      Apr 17 21:46:51 luc3as-ha hass[11884]: INFO:mysensors.mysensors:n:0 c:0 t:3 s:9 p:read: 25-25-0 s=255,c=3,t=15,pt=2,l=2,sg=0:0
      Apr 17 21:46:54 luc3as-ha hass[11884]: INFO:mysensors.mysensors:n:0 c:0 t:3 s:9 p:read: 25-25-0 s=255,c=3,t=11,pt=0,l=8,sg=0:Humidity
      Apr 17 21:46:54 luc3as-ha hass[11884]: INFO:mysensors.mysensors:n:0 c:0 t:3 s:9 p:read: 25-25-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
      Apr 17 21:46:54 luc3as-ha hass[11884]: INFO:mysensors.mysensors:n:0 c:0 t:3 s:9 p:read: 25-25-0 s=0,c=0,t=7,pt=0,l=0,sg=0:
      Apr 17 21:47:00 luc3as-ha hass[11884]: Exception in thread Thread-2:
      Apr 17 21:47:00 luc3as-ha hass[11884]: Traceback (most recent call last):
      Apr 17 21:47:00 luc3as-ha hass[11884]: File "/usr/lib/python3.4/threading.py", line 920, in _bootstrap_inner
      Apr 17 21:47:00 luc3as-ha hass[11884]: self.run()
      Apr 17 21:47:00 luc3as-ha hass[11884]: File "/root/.homeassistant/lib/mysensors/mysensors.py", line 328, in run
      Apr 17 21:47:00 luc3as-ha hass[11884]: response = self.handle_queue()
      Apr 17 21:47:00 luc3as-ha hass[11884]: File "/root/.homeassistant/lib/mysensors/mysensors.py", line 233, in handle_queue
      Apr 17 21:47:00 luc3as-ha hass[11884]: reply = func(*args, **kwargs)
      Apr 17 21:47:00 luc3as-ha hass[11884]: File "/root/.homeassistant/lib/mysensors/mysensors.py", line 115, in logic
      Apr 17 21:47:00 luc3as-ha hass[11884]: self._handle_presentation(msg)
      Apr 17 21:47:00 luc3as-ha hass[11884]: File "/root/.homeassistant/lib/mysensors/mysensors.py", line 49, in _handle_presentation
      Apr 17 21:47:00 luc3as-ha hass[11884]: self.sensors[msg.node_id].add_child_sensor(msg.child_id,
      Apr 17 21:47:00 luc3as-ha hass[11884]: KeyError: 25
      Apr 17 21:47:00 luc3as-ha hass[11884]: INFO:homeassistant.components.device_tracker.asuswrt:Checking ARP
      
      
      posted in Home Assistant
      Luc3as
      Luc3as
    • RE: Mysensor-ing a thermostatic valve

      @Sorg Hello, I am really interested in this topic, do you have any new informations or progress in this project ?

      posted in Hardware
      Luc3as
      Luc3as