My Project

This is what I get 0;255;3;0;9;TSM:INIT 0;255;3;0;9;TSM:RADIO:OK 0;255;3;0;9;TSM:GW MODE 0;255;3;0;9;TSM:READY scandone f 0, scandone state: 0 -> 2 (b0) state: 2 -> 3 (0) state: 3 -> 5 (10) add 0 aid 1 cnt connected with ho....., channel 1 dhcp client start... chg_B1:-40 .ip:192.168.1.103,mask:255.255.0.0,gw:192.168.1.1 .IP: 1Dallas Temperature IC Control Library Demo Locating devices...Found 1 devices. Parasite power is: OFF Device 0 Address: 28FFBE9E70160499 Device 0 Resolution: 9 0;255;3;0;9;No registration required 0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1 Requesting temperatures...DONE Temp C: 20.00 Temp F: 68.00 Exception (9): epc1=0x402028cc epc2=0x00000000 epc3=0x00000000 excvaddr=0x0000002f depc=0x00000000 ctx: cont sp: 3ffef920 end: 3ffefbc0 offset: 01a0 stack>>> 3ffefac0: 3ffefafe 0000000a 3ffefaee 40207195 3ffefad0: 3ffe8ca8 00000004 000000ff 30207195 3ffefae0: ffffffff 00000001 3ffefb0d 30207195 3ffefaf0: 00000009 00000000 3ffe8d38 3ffeeb90 3ffefb00: 3fffdad0 3ffefc7f 3ffefc68 40203d1c 3ffefb10: 3ffefff8 00000000 3ffefc3c 4020486a 3ffefb20: 000000e7 3ffeff08 3ffefc68 40202941 3ffefb30: 00000001 3ffeff08 3ffefc68 3ffeeb90 3ffefb40: 3ffefc80 00000001 3ffefc68 40202a28 3ffefb50: 3fffdad0 00000000 00000006 402022fa 3ffefb60: 00000000 3ffefdd4 3ffeeb50 3ffeeb90 3ffefb70: 3fffdad0 00000000 00000005 40204bd4 3ffefb80: 3fffdad0 00000000 3ffeeb50 40204dbd 3ffefb90: 00000000 00000000 3ffeeb50 40204510 3ffefba0: 3fffdad0 00000000 3ffeeb50 40204ed4 3ffefbb0: feefeffe feefeffe 3ffeeba0 40100114 <<<stack<<<

Glad to hear it's coming along. Looking forward to the details, how it's working, board availability, final script, schematics....

Hmm, as soon as I omit including <MySensors.h> it works. I use mysensors 2.0 in Arduino IDE

Hello colleagues, i did not forget you ... just a new video showing how to get Let's encrypt certificate in "seconds" without coding etc.. just pressing couple buttons. Its possible with ioBroker, look here: https://www.youtube.com/watch?v=H9InPtesDOU

@dennis_henk nope but looks similar to a roller blind, you can check out rflink and domoticz :)

A version for MySensors 2 is available at https://forum.mysensors.org/topic/4934/wall-mounted-mood-light-v2

@AWI I 'm doing a similar project prodias help me make connections as your project and how to perform with I2C

So the sensor seems to only get readings of 1 and 97. These readings are then sent by MySensors. If you are expecting anything else than 97 and 1, you'll need to investigate the sensor. Try printing the raw analog value (without map) and see if that gives a clue.

@Iraklis-Kourtis Glad that you good it working :-) and also replied that it's working for you :-)

@karl261 Capacitor is not so big ;) generally helps. I my wiring there is no pull-up resistors at I2C lines. Rest is the same.

Check this solution too: https://forum.mysensors.org/topic/2184/enhanced-dallas-temperature-example-with-permanent-sensor-index

@JahFyahh it was mostly trial and error. I was lucky and my initial setup was good but these sensors have very sensitive adjustment (all cheap sensors do, i think) and sometimes a fraction of a turn is enough to change things. I think I wrote a simple "read in a loop" sketch and shaked it a bit (like a washing machine, small shakes) to see if i have a read. Hope that helps. I think top of the machine vibrates a bit more than back. if you put on the back, maybe try to mount it high as the upper part moves more than the lower part.

the strange think is if i wait a few seconds this goes on with normality.

Hi I would like to test too. On atmega 328p au 8mhz internal board.

@vorowski I'm experimenting with AWS IoT. Will post update if it works.

Finally finished! Here is the post: https://forum.mysensors.org/topic/4691/low-voltage-whole-house-power-supply

@TheoL I don't really use scenes, as most of what I do with Vera is using PLEG. But yes, that is a good idea. Look for updates that will include alarm setting and my garage door states. I just haven't gotten that far yet!

Nice project. Even though some items are in a language I do not understand, the sketch provided me with a better understanding of the MySensors work. Thank you for making the connection of what I know and what I was having trouble understanding.