node NRF52832 with DHT22



  • hello,
    i'm trying to experiment nodes with NRF52832.
    I use this sketch :

    // Enable debug prints
    #define MY_DEBUG
    
    // Enable and select radio type attached 
    //#define MY_RADIO_RF24
    //#define MY_RADIO_RFM69
    //#define MY_RS485
    #define MY_RADIO_NRF5_ESB
    
    #include <SPI.h>
    #include <MySensors.h>  
    #include <DHT.h>
    
    // Set this to the pin you connected the DHT's data pin to
    #define DHT_DATA_PIN 08
    
    // Set this offset if the sensor has a permanent small offset to the real temperatures.
    // In Celsius degrees (as measured by the device)
    #define SENSOR_TEMP_OFFSET 0
    
    // Sleep time between sensor updates (in milliseconds)
    // Must be >1000ms for DHT22 and >2000ms for DHT11
    static const uint64_t UPDATE_INTERVAL = 6000;
    
    // Force sending an update of the temperature after n sensor reads, so a controller showing the
    // timestamp of the last update doesn't show something like 3 hours in the unlikely case, that
    // the value didn't change since;
    // i.e. the sensor would force sending an update every UPDATE_INTERVAL*FORCE_UPDATE_N_READS [ms]
    static const uint8_t FORCE_UPDATE_N_READS = 10;
    
    #define CHILD_ID_HUM 0
    #define CHILD_ID_TEMP 1
    
    float lastTemp;
    float lastHum;
    uint8_t nNoUpdatesTemp;
    uint8_t nNoUpdatesHum;
    bool metric = true;
    
    MyMessage msgHum(CHILD_ID_HUM, V_HUM);
    MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
    DHT dht;
    
    
    void presentation()  
    { 
      // Send the sketch version information to the gateway
      sendSketchInfo("TemperatureHumiditeNRF", "1.0");
    
      // Register all sensors to gw (they will be created as child devices)
      present(CHILD_ID_HUM, S_HUM);
      present(CHILD_ID_TEMP, S_TEMP);
    
      metric = getControllerConfig().isMetric;
    }
    
    
    void setup()
    {
      dht.setup(DHT_DATA_PIN); // set data pin of DHT sensor
      if (UPDATE_INTERVAL <= dht.getMinimumSamplingPeriod()) {
        Serial.println("Warning: UPDATE_INTERVAL is smaller than supported by the sensor!");
      }
      // Sleep for the time of the minimum sampling period to give the sensor time to power up
      // (otherwise, timeout errors might occure for the first reading)
      sleep(dht.getMinimumSamplingPeriod());
    }
    
    
    void loop()      
    {  
      // Force reading sensor, so it works also after sleep()
      dht.readSensor(true);
    
      // Get temperature from DHT library
      float temperature = dht.getTemperature();
      if (isnan(temperature)) {
        Serial.println("Failed reading temperature from DHT!");
      } else if (temperature != lastTemp || nNoUpdatesTemp == FORCE_UPDATE_N_READS) {
        // Only send temperature if it changed since the last measurement or if we didn't send an update for n times
        lastTemp = temperature;
    
        // apply the offset before converting to something different than Celsius degrees
        temperature += SENSOR_TEMP_OFFSET;
    
        if (!metric) {
          temperature = dht.toFahrenheit(temperature);
        }
        // Reset no updates counter
        nNoUpdatesTemp = 0;
        send(msgTemp.set(temperature, 1));
    
        #ifdef MY_DEBUG
        Serial.print("T: ");
        Serial.println(temperature);
        #endif
      } else {
        // Increase no update counter if the temperature stayed the same
        nNoUpdatesTemp++;
      }
    
      // Get humidity from DHT library
      float humidity = dht.getHumidity();
      if (isnan(humidity)) {
        Serial.println("Failed reading humidity from DHT");
      } else if (humidity != lastHum || nNoUpdatesHum == FORCE_UPDATE_N_READS) {
        // Only send humidity if it changed since the last measurement or if we didn't send an update for n times
        lastHum = humidity;
        // Reset no updates counter
        nNoUpdatesHum = 0;
        send(msgHum.set(humidity, 1));
    
        #ifdef MY_DEBUG
        Serial.print("H: ");
        Serial.println(humidity);
        #endif
      } else {
        // Increase no update counter if the humidity stayed the same
        nNoUpdatesHum++;
      }
    
      // Sleep for a while to save energy
      sleep(UPDATE_INTERVAL); 
    }
    

    But problem...
    My controlleur found my node, but no read of temperature or humidity.
    I try to change pin of data from dht22, same problem.

    Can you help me make this node running ?


Log in to reply
 

Suggested Topics

21
Online

11.2k
Users

11.1k
Topics

112.5k
Posts