RelayActuator problem - sometimes nothing happens

[BulldogLowell]

@Moshe-Livne

You could show a schematic of your rig and detail what type/size power supply you are using.

[Moshe Livne]

@BulldogLowell Calling it schematic would be an overkill. It is a nano powered by a 1A wall socket.

[BulldogLowell]

@Moshe-Livne said:

@BulldogLowell Calling it schematic would be an overkill. It is a nano powered by a 1A wall socket.

Are you powering the relay in parallel <to> edit: with the Arduino or from Arduino's Vcc?

[Moshe Livne]

currently from the arduino vcc. I have no idea how to wire it directly from the wall power. without breaking it, that it.

[BulldogLowell]

@Moshe-Livne said:

currently from the arduino vcc. I have no idea how to wire it directly from the wall power. without breaking it, that it.

Assuming you have a 5V power supply and a single channel 5V relay, it will have a Ground, Vcc and IN pins.

Connect with a wire from arduino's Vin (not Vcc) and arduino's ground. The third third (IN) will go to the arduino pin you are using to control the relay... start there.

[Moshe Livne]

@BulldogLowell Thanks, will do

[Chester]

@Moshe-Livne Depending on whether your incoming power is replaceable or hard wired in your module...

You could look into picking up one of those dual voltage wall warts, that have one output with 1A, and one output with 2.1A. You could then just use one USB lead from the 1A output to run the Arduino and radio, then use the 2.1A output to power the relay board with a sufficient loading ability.

I have done this with my 8 port SSR relay card, and so far in testing it has been super stable, and I have had no glitches in radio performance due to power drops from turning on or off the relays.

[madmax]

Hello

i have a sketch with dth22 motion and relay

it's not optimal but it works

i want to add another relay but it doesn't work have you a soluce

thanks

#include <MySensor.h>
#include <DHT.h>
#include <SimpleTimer.h>

#define CHILD_ID_HUM 1
#define CHILD_ID_TEMP 2
#define CHILD_ID_MOTION 3
#define CHILD_ID_RELAY 4

#define MOTION_SENSOR_DIGITAL_PIN 3
#define HUMIDITY_SENSOR_DIGITAL_PIN 4
#define INTERRUPT MOTION_SENSOR_DIGITAL_PIN-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define RELAY  5// Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define RELAY_ON 0  // GPIO value to write to turn on attached relay
#define RELAY_OFF 1 // GPIO value to write to turn off attached relay

unsigned long SLEEP_TIME = 600000; // Sleep time between reads (in milliseconds) - 10mins

DHT dht;
SimpleTimer timer;
float lastTemp;
float lastHum;
boolean lastTripped;
boolean metric = true;
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msg(CHILD_ID_MOTION, V_TRIPPED);

MySensor gw;
void setup()  
{ 
  // Initialize library and add callback for incoming messages
  gw.begin(incomingMessage, AUTO, true);
  
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN); 

  // Send the Sketch Version Information to the Gateway
  gw.sendSketchInfo("HumTempRelayMotion", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);
  gw.present(CHILD_ID_MOTION, S_MOTION);
  gw.present(CHILD_ID_RELAY, S_LIGHT);
  pinMode(RELAY, OUTPUT);
  digitalWrite(RELAY, gw.loadState(RELAY)?RELAY_OFF:RELAY_ON);
  
  //Serial.begin(9600);
  timer.setInterval(30000, getMeasure);
  metric = gw.getConfig().isMetric;
  
}

void loop()      
{  
  // Alway process incoming messages whenever possible
  gw.process();
  timer.run();
  
  boolean tripped = digitalRead(MOTION_SENSOR_DIGITAL_PIN) == HIGH;    
  if (tripped != lastTripped) {
    lastTripped = tripped;
    Serial.print("M: ");
    Serial.println(tripped);
    gw.send(msg.set(tripped?"1":"0"));  // Send tripped value to gw
  }

}

void incomingMessage(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_LIGHT) {
     // Change relay state
     digitalWrite(message.sensor-CHILD_ID_RELAY+RELAY, message.getBool()?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     gw.saveState(message.sensor, message.getBool());
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
}

void getMeasure() {
  delay(dht.getMinimumSamplingPeriod());

  float temperature = dht.getTemperature();
  if (isnan(temperature)) {
      Serial.println("Failed reading temperature from DHT");
  } else if (temperature != lastTemp) {
    lastTemp = temperature;
    if (!metric) {
      temperature = dht.toFahrenheit(temperature);
    }
    gw.send(msgTemp.set(temperature, 1));
    Serial.print("T: ");
    Serial.println(temperature);
  }
  
  float humidity = dht.getHumidity();
  if (isnan(humidity)) {
      Serial.println("Failed reading humidity from DHT");
  } else if (humidity != lastHum) {
      lastHum = humidity;
      gw.send(msgHum.set(humidity, 1));
      Serial.print("H: ");
      Serial.println(humidity);
  }
}```

[BulldogLowell]

@madmax

there are examples on the forum on multiple relays on one MCU... try searching the forum.

[madmax]

@BulldogLowell said:

are examples on the forum on multiple relays on one MCU... try searching the forum.

yes i see but with dth 22 it's difficult
i use simpletimer.h with this

[BulldogLowell]

@madmax

yes, so go to mutlti relay, add your libraries for simple timer and DHT. Thge relay code is non-blocking so you should be able to fold it in quite nicely.