ESP8266 WiFi gateway issue

[snow]

Hi,
I have one battery powered node build on Arduino Mini Pro 3.3V with combined 2 sensors DHT11 and BH1750. The node is working OK and give me correct values from sensors on Arduino serial console.

The output from this node connected to Serial gateway is also OK.

And this is the output from the same node connected to ESP8266 gateway. As You can see, only the first output of LIGHT_LEVEL is correct.

Could anyone check this?

[Yveaux]

@snow Could be a 8 (ATMega32) vs. 32 bit (ESP8266) issue.

1032       = 0x0000 0408
1107297279 = 0x4200 03FF

The lower 16 bits are more or less equal.
Could you post the serial output of the ESP8266 gateway for such a set of LIGHT_LEVELs and a screenshot of MYSController as you did before ?

[Dwalt]

Why does MsgID#32 provide Heater_sw as the subtype? Something strange going on with the data flowing through the esp...

[Yveaux]

@Dwalt said:

Why does MsgID#32 provide Heater_sw as the subtype? Something strange going on with the data flowing through the esp...

MsgID#32 is from the serial gateway, as I understand it...

[snow]

@Yveaux I have made another test on two gateways at the same time. Here is the results.
Serial gateway (Arduino NANO)

ESP8266 gateway (ESP-07)

Console output from ESP gateway

ESP8266 MySensors Gateway
Connecting to 00000000
...................Connected!
IP: 192.168.0.30
0;0;3;0;9;gateway started, id=0, parent=0, distance=0
Client 0 connected
0;0;3;0;14;Gateway startup complete.
0;0;3;0;9;read: 1-1-0 s=255,c=0,t=17,pt=0,l=3,sg=0:1.5
1;255;0;0;17;1.5
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
1;255;3;0;6;0
Client 0: 1;255;3;0;6;M
0;0;3;0;9;send: 0-0-1-1 s=255,c=3,t=6,pt=0,l=1,sg=0,st=ok:M
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=11,pt=0,l=22,sg=0:Lux/Temp/Humidity
1;255;3;0;11;Lux/Temp/Humidity +Bat
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
1;255;3;0;12;1.0
0;0;3;0;9;read: 1-1-0 s=0,c=0,t=16,pt=0,l=0,sg=0:
1;0;0;0;16;
0;0;3;0;9;read: 1-1-0 s=1,c=0,t=7,pt=0,l=0,sg=0:
1;1;0;0;7;
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:101
1;255;3;0;0;101
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:46
1;0;1;0;23;46
0;0;3;0;9;read: 1-1-0 s=2,c=1,t=0,pt=7,l=5,sg=0:23.0
1;2;1;0;0;23.0
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=1,pt=7,l=5,sg=0:33.0
1;1;1;0;1;33.0
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:93
1;255;3;0;0;93
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:1107296452
1;0;1;0;23;1107296452
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:1107296619
1;0;1;0;23;1107296619
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:1107296632
1;0;1;0;23;1107296632
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:1107296315
1;0;1;0;23;1107296315
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:92
1;255;3;0;0;92
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:93
1;255;3;0;0;93
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:92
1;255;3;0;0;92
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:93
1;255;3;0;0;93
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:1107296724
1;0;1;0;23;1107296724
0;0;3;0;9;read: 1-1-0 s=255,c=2,t=0,pt=1,l=1,sg=0:92
1;255;2;0;0;92
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:1107296536
1;0;1;0;23;1107296536
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:93
1;255;3;0;0;93
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=22,pt=3,l=2,sg=0:1107296631
1;0;1;0;22;1107296631
0;0;3;0;9;read: 1-1-0 s=0,c=1,t=23,pt=3,l=2,sg=0:1107296622
1;0;1;0;23;1107296622

I suspect a problem with the length or definition of variables, but I'm not a good programmer.

1107296631 - 383 = 0x4200000
1107296622 - 366 = 0x4200000

[Dwalt]

Msg54 again shows subtype 22, which is for V_HVAC_SPEED. It occurred on both the serial gateway example (top of thread) and the ESP. It seems to mess up the message at the node level. Perhaps not a problem with the gateway.

[Yveaux]

@snow said:

I suspect a problem with the length or definition of variables,

Agree. Possibly a variable somewhere that has a different size on ESP.
Hopefully tonight I can have a better look.

[Yveaux]

@Yveaux said:

Possibly a variable somewhere that has a different size on ESP

Pretty sure I found the cause: the messages exchanged between sensor and gateway contain int types.
These have a size of 2 bytes on Arduino and 4 bytes on ESP.
An int sent from the Arduino is sent as 2 bytes, but the ESP expects 4. The upper 2 will be filled with garbage.

Still a hypothesis which has to be verified & fixed.
To be continued!

[Yveaux]

@snow Please try the code in the development branch , where hek did an excellent job to standardize on datatypes being exchanged between nodes.
This will probably solve your issue.

[snow]

The development version is working OK
Thanks guys for your hard work.

[Yveaux]

@snow great to hear!
Glad I could help (and my hunch was correct )

[Hoffan]

@snow

Did you use the Development version of the ESP8266 Wifi gatewavy or for the sensor

[hek]

@Hoffan
You should probably use it on both sides to be sure to get the same size on the data types.

[Hoffan]

All the sensors that i have include before i upgrade the ESP8266 Wifi GW is now working

But its not working to include more, Nothing happens in Veran when i press start
but the gateway say this

0;0;3;0;9Client 0: 0;0;3;0;5;1t version

every time i press start

[snow]

@Hoffan said:

Did you use the Development version of the ESP8266 Wifi gatewavy or for the sensor

At the moment I only changed the gateway. It's already solved my problem with incorrect values.

[Hoffan]

@snow

But is your include button working now?
Or maybe you don't use Vera as a controller

[hek]

@Hoffan

The print looks a bit weird. I'll have to do some tests.

[snow]

@Hoffan No. I'm using DomoticZ

[Hoffan]

@hek

That sounds good, Just ask if you want me to test something..

[Hoffan]

@hek

Any News here ?

[snow]

Having another problem with a ESP8266 running as the gateway. Sensor build on Arduino Mini Pro loaded with example sketch DimmableLightWithRotaryEncoderButton.ino. Sensor and gateway firmware compiled from latest development branch v1.6 library.
The controller is a domoticz.

This is a output on the gateway console when I turn rotary encoder on the sensor.

0;0;3;0;14;Gateway startup complete.
0;0;3;0;2;1.6.0-beta
3;1;1;0;3;0
3;1;1;0;3;8
3;1;1;0;3;12
3;1;1;0;3;16
3;1;1;0;3;24
3;1;1;0;3;30
3;1;1;0;3;36
3;1;1;0;3;44
3;1;1;0;3;58
3;1;1;0;3;76
3;1;1;0;3;96
3;1;1;0;3;100

This is the output from gateway console when I move dimmer slider on the Domoticz

3;1;1;1;3;87t Version
3;1;1;1;3;80t Version
3;1;1;1;3;53t Version
3;1;1;1;3;47t Version
3;1;1;1;3;33t Version
3;1;1;1;3;20t Version
3;1;1;1;3;13t Version
3;1;1;1;3;73t Version

The problem is that the ESP8266 gateway append unnecessary characters t Version at the end of each line.
Also when dimmer slider is on the position 6%, gateway output is 3;1;1;1;3;73t Version Correct value should be 7 not 73

[hek]

@snow

Could you perhaps enable "#define MY_DEBUG" in the gateway sketch?

Would alos be interesting to see the result when you add

Serial.println(inputString);

Here:
https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/core/MyProtocolMySensors.cpp#L36

[snow]

Here is the output from the gateway console when I rotate knob on the encoder.

connected with 00000000, channel 6
ip:192.168.0.110,mask:255.255.255.0,gw:192.168.0.1
.IP: 192.168.0.110
0;0;3;0;9;gateway started, id=0, parent=0, distance=0
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:24
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:24
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:26
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:26
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:28
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:28
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:30
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:30
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:32
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:32
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:34
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:34
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:36
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:36
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:38
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:38
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:40
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:40
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:42
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:42

Here is output from the gateway console, when I slide down dimmer on the Domoticz

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=2,pt=0,l=11,sg=0:03M Version
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:0
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:0
0;0;3;0;9;Client 0: 3;1;1;1;3;93M Version
3;1;1;1;3;93M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:93M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:93M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;87M Version
3;1;1;1;3;87M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:87M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:87M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;93M Version
3;1;1;1;3;93M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:93M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:93M Version
0;0;3;0;9;Client 0: 3;1;1;1;2;03M Version
3;1;1;1;2;03M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=2,pt=0,l=11,sg=0,st=ok:03M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=2,pt=0,l=11,sg=0:03M Version
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:0
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:0
0;0;3;0;9;Client 0: 3;1;1;1;2;13M Version
3;1;1;1;2;13M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=2,pt=0,l=11,sg=0,st=ok:13M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=2,pt=0,l=11,sg=0:13M Version
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=2,l=2,sg=0:93
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:93
0;0;3;0;9;Client 0: 3;1;1;1;3;93M Version
3;1;1;1;3;93M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:93M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:93M Version
0;0;3;0;9;read: 3-3-0 s=255,c=0,t=17,pt=0,l=10,sg=0:1.6.0-beta
0;0;3;0;9;read: 3-3-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
0;0;3;0;9;Client 0: 3;255;3;0;6;M Version
3;255;3;0;6;M Version
0;0;3;0;9;send: 0-0-3-3 s=255,c=3,t=6,pt=0,l=9,sg=0,st=ok:M Version
0;0;3;0;9;read: 3-3-0 s=1,c=0,t=4,pt=0,l=0,sg=0:
0;0;3;0;9;read: 3-3-0 s=255,c=3,t=11,pt=0,l=21,sg=0:DimmableLED /w bu
0;0;3;0;9;read: 3-3-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.2
0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=1,l=1,sg=0:93
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=1,l=1,sg=0,st=ok:93
0;0;3;0;9;Client 0: 3;1;1;1;3;80M Version
3;1;1;1;3;80M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:80M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:80M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;73M Version
3;1;1;1;3;73M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:73M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:73M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;67M Version
3;1;1;1;3;67M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:67M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:67M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;60M Version
3;1;1;1;3;60M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:60M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:60M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;53M Version
3;1;1;1;3;53M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:53M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:53M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;47M Version
3;1;1;1;3;47M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:47M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:47M Version
0;0;3;0;9;Client 0: 3;1;1;1;3;40M Version
3;1;1;1;3;40M Version
0;0;3;0;9;send: 0-0-3-3 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:40M Version

0;0;3;0;9;read: 3-3-0 s=1,c=1,t=3,pt=0,l=11,sg=0:40M Version

The output from sensor console

Starting...
send: 3-3-0-0 s=255,c=0,t=17,pt=0,l=10,sg=0,st=ok:1.6.0-beta
send: 3-3-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-3 s=255,c=3,t=6,pt=0,l=9,sg=0:M Version
send: 3-3-0-0 s=1,c=0,t=4,pt=0,l=0,sg=0,st=ok:
send: 3-3-0-0 s=255,c=3,t=11,pt=0,l=21,sg=0,st=ok:DimmableLED /w button
send: 3-3-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.2
sensor started, id=3, parent=0, distance=1
Sending in last known light level to controller: 93
send: 3-3-0-0 s=1,c=1,t=3,pt=1,l=1,sg=0,st=ok:93
Ready to receive messages...
read: 0-0-3 s=1,c=1,t=3,pt=1,l=1,sg=0:93
New light level received: 93
Fading level: 1
Fading level: 2
Fading level: 3
Fading level: 4
Fading level: 5
Fading level: 6
Fading level: 7
Fading level: 8
Fading level: 9
Fading level: 10
Fading level: 11
Fading level: 12
Fading level: 13
Fading level: 14
Fading level: 15
Fading level: 16
Fading level: 17
Fading level: 18
Fading level: 19
Fading level: 20
Fading level: 21
Fading level: 22
Fading level: 23
Fading level: 24
Fading level: 25
Fading level: 26
Fading level: 27
Fading level: 28
Fading level: 29
Fading level: 30
Fading level: 31
Fading level: 32
Fading level: 33
Fading level: 34
Fading level: 35
Fading level: 36
Fading level: 37
Fading level: 38
Fading level: 39
Fading level: 40
Fading level: 41
Fading level: 42
Fading level: 43
Fading level: 44
Fading level: 45
Fading level: 46
Fading level: 47
Fading level: 48
Fading level: 49
Fading level: 50
Fading level: 51
Fading level: 52
Fading level: 53
Fading level: 54
Fading level: 55
Fading level: 56
Fading level: 57
Fading level: 58
Fading level: 59
Fading level: 60
Fading level: 61
Fading level: 62
Fading level: 63
Fading level: 64
Fading level: 65
Fading level: 66
Fading level: 67
Fading level: 68
Fading level: 69
Fading level: 70
Fading level: 71
Fading level: 72
Fading level: 73
Fading level: 74
Fading level: 75
Fading level: 76
Fading level: 77
Fading level: 78
Fading level: 79
Fading level: 80
Fading level: 81
Fading level: 82
Fading level: 83
Fading level: 84
Fading level: 85
Fading level: 86
Fading level: 87
Fading level: 88
Fading level: 89
Fading level: 90
Fading level: 91
Fading level: 92
Fading level: 93
read: 0-0-3 s=1,c=1,t=3,pt=0,l=11,sg=0:80M Version
send: 3-3-0-0 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:80M Version
New light level received: 80
Fading level: 92
Fading level: 91
Fading level: 90
Fading level: 89
Fading level: 88
Fading level: 87
Fading level: 86
Fading level: 85
Fading level: 84
Fading level: 83
Fading level: 82
Fading level: 81
Fading level: 80
read: 0-0-3 s=1,c=1,t=3,pt=0,l=11,sg=0:73M Version
send: 3-3-0-0 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:73M Version
New light level received: 73
Fading level: 79
Fading level: 78
Fading level: 77
Fading level: 76
Fading level: 75
Fading level: 74
Fading level: 73
read: 0-0-3 s=1,c=1,t=3,pt=0,l=11,sg=0:67M Version
send: 3-3-0-0 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:67M Version
New light level received: 67
Fading level: 72
Fading level: 71
Fading level: 70
Fading level: 69
Fading level: 68
Fading level: 67
read: 0-0-3 s=1,c=1,t=3,pt=0,l=11,sg=0:60M Version
send: 3-3-0-0 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:60M Version
New light level received: 60
Fading level: 66
Fading level: 65
Fading level: 64
Fading level: 63
Fading level: 62
Fading level: 61
Fading level: 60
read: 0-0-3 s=1,c=1,t=3,pt=0,l=11,sg=0:53M Version
send: 3-3-0-0 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:53M Version
New light level received: 53
Fading level: 59
Fading level: 58
Fading level: 57
Fading level: 56
Fading level: 55
Fading level: 54
Fading level: 53
read: 0-0-3 s=1,c=1,t=3,pt=0,l=11,sg=0:47M Version
send: 3-3-0-0 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:47M Version
New light level received: 47
Fading level: 52
Fading level: 51
Fading level: 50
Fading level: 49
Fading level: 48
Fading level: 47
read: 0-0-3 s=1,c=1,t=3,pt=0,l=11,sg=0:40M Version
send: 3-3-0-0 s=1,c=1,t=3,pt=0,l=11,sg=0,st=ok:40M Version
New light level received: 40
Fading level: 46
Fading level: 45
Fading level: 44
Fading level: 43
Fading level: 42
Fading level: 41
Fading level: 40

I hope it will be helpful

[hek]

It almost looks like Domoticz sends the "Version" stuff. Is it possible to see what Domoticz sends? Anot logs over there?

[snow]

Output from RPi console. pi@domoticz ~/domoticz $ sudo ./domoticz -verbose 1

2015-11-08 15:06:57.916  MySensors: connected to: 192.168.0.110:5003
2015-11-08 15:06:57.916  MySensors: Gateway Ready...
2015-11-08 15:06:58.917  MySensors: Gateway Version: 1.6.0-beta
2015-11-08 15:07:12.928  MySensors: Node: 3, Sketch Name: DimmableLED /w button
2015-11-08 15:07:13.932  MySensors: Node: 3, Sketch Version: 1.2
subtype       = AC
Sequence nbr  = 0
ID            = 0000003
Unit          = 1
Command       = On
2015-11-08 15:07:13.936  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 0
ID            = 0000003
Unit          = 1
Command       = Set Level: 12
2015-11-08 15:07:32.010  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 1
ID            = 0000003
Unit          = 1
Command       = Set Level: 11
2015-11-08 15:07:33.981  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 2
ID            = 0000003
Unit          = 1
Command       = Set Level: 10
2015-11-08 15:07:35.984  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 3
ID            = 0000003
Unit          = 1
Command       = Set Level: 9
2015-11-08 15:07:38.055  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 4
ID            = 0000003
Unit          = 1
Command       = Set Level: 8

I'll try to build Serial Gateway and do the same test

[GizMoCuz]

There is a small problem with domoticz regarding the light level (fixed in beta #3563)
When the slider was set to 100%, around 93% was send to the node

BUT, what domoticz sends, is OK, there is NO version stuff added (really strange your seeing this!)

I made a test sketch, and this is the output:

Starting...
send: 254-254-0-0 s=255,c=0,t=17,pt=0,l=10,sg=0,st=ok:1.6.0-beta
send: 254-254-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-254 s=255,c=3,t=6,pt=0,l=1,sg=0:M
send: 254-254-0-0 s=1,c=0,t=4,pt=0,l=0,sg=0,st=ok:
send: 254-254-0-0 s=255,c=3,t=11,pt=0,l=21,sg=0,st=ok:DimmableLED /w button
send: 254-254-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.2
sensor started, id=254, parent=0, distance=1
Ready to receive messages...
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:0
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:0
V_LIGHT received: 0
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:1
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:1
V_LIGHT received: 1
read: 0-0-254 s=1,c=1,t=3,pt=0,l=2,sg=0:43
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:43
V_DIMMER received: 43
read: 0-0-254 s=1,c=1,t=3,pt=0,l=2,sg=0:86
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:86
V_DIMMER received: 86
read: 0-0-254 s=1,c=1,t=3,pt=0,l=3,sg=0:100
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=3,sg=0,st=ok:100
V_DIMMER received: 100

All perfect

Sketch:
// Enable debug prints
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#define MY_NODE_ID 254

#include <SPI.h>
#include <MySensor.h>

#define SN "DimmableLED /w button"
#define SV "1.2"

#define CHILD_ID_LIGHT 1

MyMessage dimmerMsg(CHILD_ID_LIGHT, V_DIMMER);

void setup()
{
Serial.println("Ready to receive messages...");
}

void presentation() {
// Send the Sketch Version Information to the Gateway
present(CHILD_ID_LIGHT, S_DIMMER);
sendSketchInfo(SN, SV);
}

void loop()
{
}

void receive(const MyMessage &message)
{
if (message.type == V_LIGHT) {
Serial.print("V_LIGHT received: ");
Serial.println(message.getString());
} else if (message.type == V_DIMMER) {
Serial.print("V_DIMMER received: ");
Serial.println(message.getString());
}
else {
Serial.print("Unhandled message received: ");
Serial.println(message.getString());
}
}

[hek]

@GizMoCuz
How do you terminate the strings in Domoticz? Only \n or both \n and \r?

Does the controller have exactly the same behaviour when communicating with an ethernet gateway as serial gateway?

[snow]

@GizMoCuz
I have tested Your sketch and the same stuff is added at the end

Starting...
send: 254-254-0-0 s=255,c=0,t=17,pt=0,l=10,sg=0,st=ok:1.6.0-beta
send: 254-254-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-254 s=255,c=3,t=6,pt=0,l=7,sg=0:Mersion
send: 254-254-0-0 s=1,c=0,t=4,pt=0,l=0,sg=0,st=ok:
send: 254-254-0-0 s=255,c=3,t=11,pt=0,l=21,sg=0,st=ok:DimmableLED /w button
send: 254-254-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.2
sensor started, id=254, parent=0, distance=1
Ready to receive messages...
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:0
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:0
V_LIGHT received: 0
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:1
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:1
V_LIGHT received: 1
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:93Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:93Mersion
V_DIMMER received: 93Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:86Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:86Mersion
V_DIMMER received: 86Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:79Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:79Mersion
V_DIMMER received: 79Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:71Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:71Mersion
V_DIMMER received: 71Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:64Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:64Mersion
V_DIMMER received: 64Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:57Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:57Mersion
V_DIMMER received: 57Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:50Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:50Mersion
V_DIMMER received: 50Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:43Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:43Mersion
V_DIMMER received: 43Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:36Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:36Mersion
V_DIMMER received: 36Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:29Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:29Mersion
V_DIMMER received: 29Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:21Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:21Mersion
V_DIMMER received: 21Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:14Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:14Mersion
V_DIMMER received: 14Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:74Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:74Mersion
V_DIMMER received: 74Mersion
read: 0-0-254 s=1,c=1,t=2,pt=0,l=9,sg=0:04Mersion
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=9,sg=0,st=ok:04Mersion
V_LIGHT received: 04Mersion

Is it possible as some crap is sitting in my ESP8266 EEPROM memory?

[GizMoCuz]

@hek, with \n
MySensors is implemented in domoticz for a long time now... there should be nothing wrong with it.....

Also in my sketches all is received perfectly

Could there be a difference between the ESP8266 and nRF ?
I only use the nRF currently (and probably will for ever as i have 20 more chips and a lot more arduino's g)

Also i do not send anything with the word version in it, it looks this is a left over from sending the sketch information ?

I dont know how you guys get that nice colors in the log (brown/white/green), but the green number is OK, that white behind it is not

[GizMoCuz]

@hek, as demonstrated with the new V_CUSTOM, there is send a lot of information from domoticz -> node, and all prints well, so maybe thats a confirm that this part is working OK (at least on the nRF024)

[GizMoCuz]

I also find it strange that at the beginning V_LIGHT correctly displays 0 or 1, and at the end 04 ? (0 = OK)

[snow]

I made a Serial Gateway and updated Domoticz to latest beta, and this is the output from the same sensor.

0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=1,sg=0,st=ok:7
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=1,sg=0:7
2;1;1;1;3;7
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:14
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:14
2;1;1;1;3;14
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:21
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:21
2;1;1;1;3;21
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:29
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:29
2;1;1;1;3;29
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:36
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:36
2;1;1;1;3;36
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:43
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:43
2;1;1;1;3;43
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:50
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:50
2;1;1;1;3;50
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:57
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:57
2;1;1;1;3;57
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:64
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:64
2;1;1;1;3;64
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:71
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:71
2;1;1;1;3;71
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:79
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:79
2;1;1;1;3;79
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:86
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:86
2;1;1;1;3;86
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:93
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:93
2;1;1;1;3;93
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=3,sg=0,st=ok:100
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=3,sg=0:100
2;1;1;1;3;100

All OK

[hek]

@snow

Could you try replacing this in MySensors/core/MyGatewayTransportEthernet.cpp

bool _readFromClient(uint8_t i) {
	while (clients[i].connected() && clients[i].available()) {
		char inChar = clients[i].read();
		if (inputString[i].idx < MY_GATEWAY_MAX_RECEIVE_LENGTH - 1) {
			// if newline then command is complete
			if (inChar == '\n') {
				// a command was issued by the client
				// we will now try to send it to the actuator
				// echo the string to the serial port
				debug(PSTR("Client %d: %s\n"), i, inputString[i].string);

				// add string terminator and clear the string:
				inputString[i].string[inputString[i].idx] = 0;
				inputString[i].idx = 0;
				bool ret = protocolParse(_ethernetMsg, inputString[i].string);
				if (ret) {
					return ret;
				}

			} else {
				// add it to the inputString:
				inputString[i].string[inputString[i].idx++] = inChar;
			}
		} else {
			// Incoming message too long. Throw away
			debug(PSTR("Client %d: Message too long\n"), i);
			inputString[i].idx = 0;
			// Finished with this client's message. Next loop() we'll see if there's more to read.
			break;
		}
	}
	return false;
}

And let me know how it behaves.

[GizMoCuz]

I think that will solve the issue... @snow, waiting patiently for your reply

[snow]

It's much better now. I can control dimmer from the domoticz.

0;0;3;0;9;Client 0 connected
0;0;3;0;9;Client 0: 0;0;3;0;2;Get Version
0;0;3;0;2;Get Version
0;0;3;0;9;read: 2-2-0 s=255,c=0,t=17,pt=0,l=10,sg=0:1.6.0-beta
0;0;3;0;9;read: 2-2-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
0;0;3;0;9;Client 0: 2;255;3;0;6;M Version
2;255;3;0;6;M
0;0;3;0;9;send: 0-0-2-2 s=255,c=3,t=6,pt=0,l=1,sg=0,st=ok:M
0;0;3;0;9;read: 2-2-0 s=1,c=0,t=4,pt=0,l=0,sg=0:
0;0;3;0;9;read: 2-2-0 s=255,c=3,t=11,pt=0,l=21,sg=0:DimmableLED /w bu
0;0;3;0;9;read: 2-2-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.2
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=1,l=1,sg=0:100
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=1,l=1,sg=0,st=ok:100
0;0;3;0;9;Client 0: 2;1;1;1;3;93M
2;1;1;1;3;93
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:93
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:93
0;0;3;0;9;Client 0: 2;1;1;1;3;86
2;1;1;1;3;86
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:86
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:86
0;0;3;0;9;Client 0: 2;1;1;1;3;79
2;1;1;1;3;79
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:79
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:79
0;0;3;0;9;Client 0: 2;1;1;1;3;71
2;1;1;1;3;71
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:71
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:71
0;0;3;0;9;Client 0: 2;1;1;1;3;64
2;1;1;1;3;64
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:64
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:64
0;0;3;0;9;Client 0: 2;1;1;1;3;57
2;1;1;1;3;57
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:57
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:57
0;0;3;0;9;Client 0: 2;1;1;1;3;50
2;1;1;1;3;50
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:50
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:50
0;0;3;0;9;Client 0: 2;1;1;1;3;43
2;1;1;1;3;43
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:43
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:43
0;0;3;0;9;Client 0: 2;1;1;1;3;36
2;1;1;1;3;36
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:36
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:36
0;0;3;0;9;Client 0: 2;1;1;1;3;36
2;1;1;1;3;36
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:36
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:36
0;0;3;0;9;Client 0: 2;1;1;1;3;29
2;1;1;1;3;29
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:29
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:29
0;0;3;0;9;Client 0: 2;1;1;1;3;21
2;1;1;1;3;21
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:21
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:21
0;0;3;0;9;Client 0: 2;1;1;1;3;14
2;1;1;1;3;14
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:14
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:14
0;0;3;0;9;Client 0: 2;1;1;1;3;74
2;1;1;1;3;7
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=1,sg=0,st=ok:7
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=1,sg=0:7
0;0;3;0;9;Client 0: 2;1;1;1;2;0
2;1;1;1;2;0
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:0
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=2,pt=0,l=1,sg=0:0
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=2,l=2,sg=0:0
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:0

[hek]

Great, I'll push this fix ASAP.

[Hoffan]

@Hoffan said:
anyone that knows if include button working now? With vera as controller

[Hoffan]

I can answer that question by my self.. Its still not working

[hek]

@Hoffan, I verified the inclusion button functionality in the dev branch during the weekend (at least on AtMega but it should work fine on ESP as well).

Just make sure to enable the feature and set a valid ESP-pin. All is documented in sketch.

[Hoffan]

@hek

Okey So i must enable it in the sketch even if i only use the start button in the GUI in Vera

[hek]

@Hoffan
Not the "button" feature (unless you use it), but the "inclusion mode" feature must be enabled.

[Hoffan]

I don't know if i understan you right here, @Hek

if i like to use the start button in vera should it look like this

// Enable inclusion mode
define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN 3

[hek]

You only need these two:

#define MY_INCLUSION_MODE_FEATURE
#define MY_INCLUSION_MODE_DURATION 60

[Hoffan]

Yes That i understand, But Nothing is still happening in the GUI men i press start

[hek]

Anything in the gateway log?

[Hoffan]

[hek]

Hmm. ok so message reaches gateway. Good start. It should reply back to Vera. with a
0;0;3;0;5;1

Unfortunately there is no debug log for this in the code. So I can't see if the message is sent to your controller. So either you'll have to look in the Vera log or add a

Serial.println(_ethernetMessage);

Here: https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/core/MyGatewayTransportEthernet.cpp#L170

To see that the message is actually sent back to vera.

[Hoffan]

You mean that i should change that line #170 år just put in the serial string

[hek]

Add the string debug print.