Can't ping Ethernet Gateway ENC28J60 + Arduino Nano Clone

[hek]

Not sure anyone has bothered checking with the latest version of the library....

My experience is that the enc-module is really unreliable (and CPU intensive). Save yourself a lot of problems and get the W5100 module which offloads much of the work.

[MLs]

Hello I upload ENC28J60 Ethernet sample file from MySensors and it worked with MySensors Lib 2.1.1. And I used the Arduino Pro Mini, nRF24L01 Radio and ENC28J60 Ethernet. Do you use Arduino Pro Mini, you must disable debugging.

//Mattias

[cadet]

I was try with nano and shield and nrf24
Also i was try uno
I was comment all! Led, debug and no result
Only comment nrf24 will help and ethernet will ping.
Waiting for ftdi and w5100 (

[cadet]

@MLs
Please post the code

[MLs]

@cadet

You need to 'change the IP addresses

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik EKblad
 * Contribution by a-lurker and Anticimex,
 * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
 * Contribution by Tomas Hozza <thozza@gmail.com>
 *
 *
 * DESCRIPTION
 * The EthernetGateway sends data received from sensors to the ethernet link.
 * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
 *
 * The GW code is designed for Arduino 328p / 16MHz.  ATmega168 does not have enough memory to run this program.
 *
 * LED purposes:
 * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error
 *
 * See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
 *
 */

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// When ENC28J60 is connected we have to move CE/CSN pins for NRF radio
#define MY_RF24_CE_PIN 5
#define MY_RF24_CS_PIN 6

// Enable gateway ethernet module type 
#define MY_GATEWAY_ENC28J60

// Gateway IP address
#define MY_IP_ADDRESS 192,168,0,178 

// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003   

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
#define MY_CONTROLLER_IP_ADDRESS 192, 168, 0, 201   

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xFE

// Flash leds on rx/tx/err
//#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  9  // the PCB, on board LED

#include <SPI.h>
#include <UIPEthernet.h>
#include <MySensors.h>


void setup()
{
}

void loop() {
}

//Mattias

[cadet]

@MLs
I think you use enc28 ethernet module not shield

I have same code but no ping if nrf not commented

[MLs]

@cadet

Yes, I put together this some years ago. But now i uses W5100 instead.

//Mattias

[cadet]

@MLs

I'm also use W5100 now, but have two enc28 shield )

[MLs]

@cadet

Ok, you have linked NRF24 radio right?

https://www.mysensors.org/build/ethernet_gateway#enc28j60-ethernet-module

Also verified that the shield is properly attached?
//Mattias

[cadet]

@MLs
Nano with shield and no nrf24 ping only with commented nrf24
Then uncomment nrf24 GW has no connection over ethernet
No ping no telnet

[MLs]

@cadet

There I can say is that the circuit ENC28J60 works with MySensors lib 2.1.1
Try to connect your components to breadboard.

[cadet]

@MLs
And that way I was tested
Connect via breadboard to nano and uno
With same results

[MLs]

@cadet

I'm no expert but I would have looked at the data sheet and measured up to make sure that the hardware are not defective in any way.

http://ww1.microchip.com/downloads/en/DeviceDoc/39662c.pdf

Or the radio.

//Mattias