Raspberry Gateway + Arduino pro mini (atmega328p) NRF24L01 (without plus +)

[mfalkvidd]

@alop edit it with your favorite editor?

[alop]

@mfalkvidd Ok, so far :)
But do I need to "compile", "build", "make" something so that changes in MyConfig.h will be taken?

[mfalkvidd]

@alop ok :)

I think make is sufficient (and make install if you want the new binary installed).

make is smart enough to recompile everything that has been modified.

[alop]

@mfalkvidd
Unfortunatelly no change after adding capacitor :(
Now I have bought NRF24L01 WITH Plus and I'm trying with them.
I have reinstalled from skratch everything.
Gateway and sensor are now ca. 3-4 meters appart.

Sketch on atmega328p (light sensor)

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik EKblad
 *
 * DESCRIPTION
 * Example sketch showing how to measue light level using a LM393 photo-resistor
 * http://www.mysensors.org/build/light
 */

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <MySensors.h>

#define CHILD_ID_LIGHT 15
#define LIGHT_SENSOR_ANALOG_PIN 0

unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)

MyMessage msg(CHILD_ID_LIGHT, V_LIGHT_LEVEL);
int lastLightLevel;


void presentation()
{
    // Send the sketch version information to the gateway and Controller
    sendSketchInfo("Light Sensor", "1.0");

    // Register all sensors to gateway (they will be created as child devices)
    present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
}

void loop()
{
    int16_t lightLevel = (1023-analogRead(LIGHT_SENSOR_ANALOG_PIN))/10.23;
    Serial.println(lightLevel);
    if (lightLevel != lastLightLevel) {
        send(msg.set(lightLevel));
        lastLightLevel = lightLevel;
    }
    sleep(SLEEP_TIME);
}

On raspberry

./configure --my-transport=nrf24 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020

Serial on the sensor

114445 !TSM:FPAR:NO REPLY
114447 TSM:FPAR
114449 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
116457 !TSM:FPAR:FAIL
116459 TSM:FAIL:CNT=7
116461 TSM:FAIL:DIS
116463 TSF:TDI:TSL
176465 TSM:FAIL:RE-INIT
176467 TSM:INIT
176475 TSM:INIT:TSP OK
176477 TSM:FPAR
176479 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
178487 !TSM:FPAR:NO REPLY
178489 TSM:FPAR
178491 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
180499 !TSM:FPAR:NO REPLY
180501 TSM:FPAR
180503 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
182511 !TSM:FPAR:NO REPLY
182513 TSM:FPAR
182515 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:

on raspberry

pi@RP3HA:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-beta
mysgw: MCO:BGN:INIT GW,CP=RNNG----,VER=2.2.0-beta
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1

And on my home automation (home assistant)

2017-07-22 13:00:19 ERROR (Thread-13) [mysensors.gateway_serial] Unable to connect to /dev/ttyUSB020

Update:
After 15-20 minutes running the gateway I received following lines:

mysgw: TSF:SAN:OK
mysgw: TSM:READY:NWD REQ
mysgw: TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:

[alop]

It's a workaroud, but not "nice".
Since I have no problem on creating gateway on another arduino pro mini, I just connected per USB the arduino to RP3 and everything is working fine.
So sensors can be read by a controller (home assistant).
Big downside is, that for pro mini I have to use usb to ttl convertor in between.
Maybe the code for raspberry is with bugs, since to be able to see my rf radio on raspberry I had to install the "development" branch.

[gohan]

the development branch works well, why don't you use it on the RPI?

[alop]

@gohan As described above, there was no connection between serial gateway on RPi und sensor nodes.
Above is the whole setup described. Wiring is taken from the mysensors web site.

[gohan]

I am referring to create an ethernet gw running on the RPI instead of a serial gw.

[alop]

@gohan I do not have ethernet hardware. I just wanted to connect radio directly to RPI

[gohan]

Just follow the guide of raspberry gateway and choose to configure it as ethernet, it makes it easier to setup con controller.

[alop]

@gohan said in Raspberry Gateway + Arduino pro mini (atmega328p) NRF24L01 (without plus +):

choose to configure it as ethernet, .

But if I understand right, I need ethernet gateway hardware, or am I missing something?

[gohan]

The RPI becomes an ethernet gateway.