💬 Micro (nano) ampere meter (double)

[rvendrame]

@Nca78 , updating: I figured out how to connect the load, so I'm done with it (including calibration).

I changed the original code a bit, as I also wanted it a bit more responsive. I didn't lift pin 15 as you did.

BTW, what bootloader + clock are you using? Perhaps that could influence? I'm using MYSBootloaderV13pre.hex, 8Mhz internal clock...

Changes:

• Less average reading per cycle (from 32 to 4 ) --> Didn't notice significant changes in measurements.
• More accumulated avg reads ( from 16 to 32 ) --> Just to keep a less volatile avg numbers in display.
• Change the logic of short/long press. short press (~1s) = change mode, long press (~3s) = Offset.

In case you want to give it a try...

// uA meter with HX711
/*
 PROJECT: MySensors - uA meter with HX711
 PROGRAMMER: AWI
 DATE: 20170414/ last update: 
 FILE: AWI_uA_meter.ino
 LICENSE: Public domain

 Performance improvements: rvendrame 
 
Hardware: tbd Nano ATmega328p board w/ NRF24l01
	
Special:
	program with Arduino Nano
	
SUMMARY:
	Measures mV accross a shunt resistor ~ uA - channel A
	Measures mV on channel B
	Modes:
		- default: measure uV in full resolution (Stable reading only for 0.1uV)
		- other:
			A: channel A: default, amplification 128 - div 500: 0.1uV stable,  range +/- 20mV, (1ohm +/- 20mA, res 100 nA)
			B: channel B: amplification 32 - div 125: 100nA stable, range +/- 80mV,  (10 ohm +/- 8 mA, res 10 nA)
			AB: both channels:  
		- uA - calibration: depending on the actual shunt:
			0.47 ohm -> 1 uV ~ 2uA, range -40 mA - 40 mA
			1 ohm -> 1 uV = 1uA, range -20 mA - 20 mA
			10 ohm -> 1 uv = 0.1uA
		- mV - calibration, depend on amplification
	Button switch:
		- Short press, reset current channel to offset 0 (keep terminals shorted, no need with uA ;-)
		- Long press, change channel A (uA) / B(uA)/ A & B (uA)
		
	Hx711 24bit weight scale sensor
		- Noise and temperature sensitive (x bit effective)
	OLED 128x64 display
	
Remarks:
	Size is large as result of font library for display
update:
	
*/

#include <U8g2lib.h>									// U8glib for OLED display
#include <Wire.h> 										// I2C
#include <Button.h>										// https://github.com/JChristensen/Button
#include "HX711.h"										// local ADC lib

const double calibrationFactorA = 599.18f ;				// calibration for channel A: set to 1.0 for known current and divide
const double calibrationFactorB = 149.76f ;				// calibration for channel B: set to 1.0 for known current and divide
long offsetChannelA = 0 ;								// channel offsets for A and B (drifts) are calibrated at startup and on command. 
long offsetChannelB = 0 ;

const uint8_t HX711_dout = A1 ;							// HX711 data out pin
const uint8_t HX711_sck = A0 ;							// HX711 serial clock
const uint8_t buttonPin = A2 ;							// connects the button to select function and reset offset
//const unsigned long longPress = 1500UL ;				//	- long press set reference temperature - in ms												// 	- when alarm, short press resets alarm	
Button myBtn(buttonPin, true,  true, 40);				// Declare the button( pin, pullup, invert, debounce ms)

enum convertMode_t {channelA, channelB, channelAB} ;	// measurement modes, 32 port B / 128 port A / A & B

HX711 scale;											// instantiate ADC

// U8G instantiate, Change this constructor to match the display!!!
U8G2_SSD1306_128X64_NONAME_1_HW_I2C u8g(U8G2_R0, /* reset=*/ U8X8_PIN_NONE);   // All Boards without Reset of the Display

const int nettReadingsSize = 32 ; 						// the number of readings to determine the average and calculate variance/ accuracy
double lastReading, lastReadingB ; 
double nettReadings[nettReadingsSize] ; 				// store the rolling average of readings
int nettReadingPointer = 0 ; 

convertMode_t convertMode = channelA ;					// default channelA

enum state_t {idleState, waitForRelease} ;      // define possible states
static state_t state = idleState ;  


void setup() {
	Serial.begin(115200);

  Serial.println("AWI uA meter");

	// u8g setup
	u8g.begin() ;
	u8g.setFont(u8g2_font_helvR14_tf);					// 'r' = reduced (or 'n' = numeric) font only for size
	//u8g.setFont(u8g2_font_profont15_tf);					// 'r' = reduced (or 'n' = numeric) font only for size

	// HX711.DOUT	- pin #A1
	// HX711.PD_SCK	- pin #A0
	// if parameter "gain" is ommited; the default value 128 is used by the library
	//   64 & 128 is port A ; 32 is port B
	scale.begin(HX711_dout, HX711_sck, 128); 			// set port based on state of selection

	LCD_banner("Initializing") ;
	Serial.print("read average: \t\t");
	Serial.println(scale.read_average(20));  			// print the average of 20 raw readings from the ADC
	
	getOffset();										// get the offsets (drift values)
	scale.set_offset(offsetChannelA) ;					// set it for measured channel
	scale.set_scale(calibrationFactorA);				// this value is obtained by calibrating with known value; see the README for details
	
	Serial.print("read: \t\t");
	Serial.println(scale.read());						// print a raw reading from the ADC
	Serial.print("read average: \t\t");
	Serial.println(scale.read_average(10));				// print the average of 20 readings from the ADC
	Serial.print("get value: \t\t");
	Serial.println(scale.get_value(5));					// print the average of 5 readings from the ADC minus the tare weight, set with tare()
	Serial.print("get units: \t\t");
	Serial.println(scale.get_units(5), 3);				// print the average of 5 readings from the ADC minus tare weight, divided by scale
	Serial.println("Readings:");
}

void loop() {

	//Serial.print("one reading:\t");
	//Serial.print(scale.get_units(), 1);
	//Serial.print("\t| average:\t");
	//Serial.println(scale.get_units(30), 3);

  checkButton(); 
  
	// get ADC readings dependent on setting: read A, B or A & B
	// only A reads has average buffer when A&B mode is selected
	if (convertMode == channelA){
		scale.set_gain(128) ;
		scale.set_offset(offsetChannelA) ;
		scale.set_scale(calibrationFactorA );			// set division to A value and set mode to A
		lastReading = scale.get_units(4) ; 			// get value (average 4 readings)corrected with scaling
		nettReadings[nettReadingPointer] = lastReading ;	// store readings in averagebuffer
		nettReadingPointer = (++nettReadingPointer) % nettReadingsSize ; // increment and wrap
    checkButton(); 
    LCD_local_display();
	} else if (convertMode == channelB){
		scale.set_gain(32) ;
		scale.set_offset(offsetChannelB) ;
		scale.set_scale(calibrationFactorB);			// set division to B value and set mode to B
		lastReading = scale.get_units(4) ; 		  	// get value (average 4 readings)corrected with scaling
		nettReadings[nettReadingPointer] = lastReading ;	// store readings in averagebuffer
		nettReadingPointer = (++nettReadingPointer) % nettReadingsSize ; // increment and wrap
    checkButton(); 
    LCD_local_display();
	} else if (convertMode == channelAB){				// if both channels average 128 readings iso 32 (no buffer)
		scale.set_gain(128) ;
		scale.set_offset(offsetChannelA) ;
		scale.set_scale(calibrationFactorA);			// set division to A value and set mode to A
		lastReading = scale.get_units(2) ; 		  	// get value (average 4 readings)corrected with scaling
		checkButton(); 
		scale.set_gain(32) ;
		scale.set_offset(offsetChannelB) ;
		scale.set_scale(calibrationFactorB);			// set division to A value and set mode to A
		lastReadingB = scale.get_units(2) ; 			// get value (average 4 readings) corrected with scaling
    checkButton(); 
		LCD_local_displayAB();
	}
	//scale.power_down();			       				// put the ADC in sleep mode
	//delay(500);
	//scale.power_up();
	//delay(100);
}

void checkButton() { 
  
  myBtn.read();                   // read button state
  
  switch (state){
     case idleState:                  // Idle
      if (myBtn.wasPressed()) {       // Pressed 
        // change channel and wait release
        state = waitForRelease ;
      }
      break ;
    case waitForRelease:  
      if (myBtn.pressedFor(3000UL)) {  // Long Press 
         LCD_banner("Offset");
         getOffset();              
         state = idleState; 
      } else if (myBtn.wasReleased()) { // Short Press  
        state = idleState;
        switchMode() ;
      }
      break ;
    
  }
  
}
void LCD_banner(const char *s){
/* prints all avaiable variables on LCD display with units
	input: all "last" variables
*/
	u8g.firstPage();
	do {
		int strWidth = u8g.getStrWidth(s) ;				// get the length of the string to determine print position
		u8g.drawStr((128- strWidth)/2, 40, s ) ;			// print right aligned 
	} while (u8g.nextPage()) ;
}


void LCD_local_display(void){
/* prints all avaiable variables on LCD display with units
	input: all "last" variables
*/
	char buf[21];  										// buffer for max 20 char display
	char lastNettBuf[14];
	dtostrf(lastReading, 10, 2, lastNettBuf);			// Convert real to char
	char averageNettBuf[14];
	dtostrf(nettReadingsAverage(), 10, 2, averageNettBuf);	// Convert real to char
	char spreadNettBuf[14];
	dtostrf(nettReadingsSpread(), 10, 2, spreadNettBuf);	// Convert real to char
	Serial.print("Average: \t") ; Serial.print(nettReadingsAverage());
	Serial.print("\tSpread: \t") ; Serial.println(nettReadingsSpread());

	u8g.firstPage();
	do {
    checkButton(); 
		snprintf(buf, sizeof buf, "Current %s", (convertMode==channelB)?"B":"A"); // Header
		int strWidth = u8g.getStrWidth(buf) ;			//   length of the string to determine print position
		u8g.drawStr((128- strWidth)/2, 14, buf ) ;		//   print middle aligned 
		u8g.drawStr(0,31,"I") ;							// Current
		snprintf(buf, sizeof buf, "%10s\xB5\A", lastNettBuf);
		strWidth = u8g.getStrWidth(buf) ;				//   length of the string to determine print position
		u8g.drawStr((128- strWidth), 31, buf ) ;		//   print right aligned 
		u8g.drawStr(0,47,"avg") ;						// Average current
		snprintf(buf, sizeof buf, "%10s\xB5\A", averageNettBuf);
		strWidth = u8g.getStrWidth(buf) ;				// get the length of the string to determine print position
		u8g.drawStr((128- strWidth), 47, buf ) ;		// print right aligned 
		u8g.drawStr(0,63,"d\xB1") ;						// delta +/-
		snprintf(buf, sizeof buf, "%10s\xB5\A", spreadNettBuf);
		strWidth = u8g.getStrWidth(buf) ;				// get the length of the string to determine print position
		u8g.drawStr((128- strWidth), 63, buf ) ;		// print right aligned 
	} while (u8g.nextPage()) ;
}
void LCD_local_displayAB(void){
/* prints A & B channel on LCD display with units
	input: all "last" variables
*/
	char buf[21];  										// buffer for max 20 char display
	char lastNettBuf[14];
	dtostrf(lastReading, 10, 2, lastNettBuf);			// Convert real to char
	char lastNettBufB[14];
	dtostrf(lastReadingB, 10, 2, lastNettBufB);			// Convert real to char
	char lastNettBufAB[14];
	dtostrf(lastReading +lastReadingB, 10, 2, lastNettBufAB);	// Convert real to char for added values
	u8g.firstPage();
	do {
    checkButton(); 
		snprintf(buf, sizeof buf, "Current A+B"); 		// Header
		int strWidth = u8g.getStrWidth(buf) ;			//   length of the string to determine print position
		u8g.drawStr((128- strWidth)/2, 14, buf ) ;		//   print middle aligned 
		u8g.drawStr(0,31,"IA");							// Current A
		snprintf(buf, sizeof buf, "%10s\xB5\A", lastNettBuf);
		strWidth = u8g.getStrWidth(buf) ;				//   length of the string to determine print position
		u8g.drawStr((128- strWidth), 31, buf ) ;		//   print right aligned 
		u8g.drawStr(0,47,"IB");							// Current B
		snprintf(buf, sizeof buf, "%10s\xB5\A", lastNettBufB);
		strWidth = u8g.getStrWidth(buf) ;				//   length of the string to determine print position
		u8g.drawStr((128- strWidth), 47, buf ) ;		//   print right aligned 
		u8g.drawStr(0,63,"A+B");						// Current A + B
		snprintf(buf, sizeof buf, "%10s\xB5\A", lastNettBufAB);
		strWidth = u8g.getStrWidth(buf) ;				//   length of the string to determine print position
		u8g.drawStr((128- strWidth), 63, buf ) ;		//   print right aligned 
	} while (u8g.nextPage()) ;
}

// calculate average of nett readings
double nettReadingsAverage() {
	double sum = 0;
	for (byte i = 0; i < nettReadingsSize; i++) {
		sum += nettReadings[ i ];
	}
	return sum / nettReadingsSize;
}

// calculate spread of nett readings (+/-)
double nettReadingsSpread() {
	double minReading = nettReadings[0];
	double maxReading = minReading ;
	for (byte i = 1; i < nettReadingsSize; i++) {
    checkButton(); 
		if (minReading > nettReadings[ i ]){
			minReading = nettReadings[i] ;
		}
		if (maxReading < nettReadings[ i ]){
			maxReading = nettReadings[i] ; 
		}
	}
	return (maxReading - minReading)/2 ;
}

// switch the mode
void switchMode(){
	if (convertMode == channelA){
		convertMode = channelB ;
	} else if (convertMode == channelB){
		convertMode = channelAB ;
	} else {
		convertMode = channelA ;
	}
}

// assuming both channels are shorted, calculate the offset values for channel A and B
double getOffset(){
	scale.set_gain(128) ;							// get channel A
	offsetChannelA = scale.read_average(32) ;		// average 512 readings for offset
	Serial.print("Offset A: \t") ; 
	Serial.println(offsetChannelA);
	scale.set_gain(32) ;							// get channel B
	offsetChannelB = scale.read_average(32) ;		// average 512 readings for offset
	Serial.print("Offset B: \t") ; 
	Serial.println(offsetChannelB);
}```

[Nca78]

@rvendrame thank you I will try it, good idea for the button change.
Just need to change the code for another screen as I broke my oled :(

[NeverDie]

For the short press, with the original code, I noticed that an easy way to get it every time is to press until the display changes, then release. Anyhow, worked for me.

[mfalkvidd]

@AWI I'm unable to find the "local ADC lib". Is it available somewhere?

[AWI]

@mfalkvidd the 'local adc' library is the hx711 library which I placed in the sketch folder. Sorry for the confusion

[mfalkvidd]

@AWI where can I download it? It does not seem to be compatible with the hx711 library I found through the Arduino IDE Library Manager :(

EDIT: Seems to work with https://github.com/bogde/HX711 (if installing it manually)

[rmtucker]

I am confused the 1k resistors seem to be wired differently in AWI photo's and Nca78 photo's.
I would like to build this but not certain how it is wired now

[Nca78]

@rmtucker said in 💬 Micro (nano) ampere meter (double):

I am confused the 1k resistors seem to be wired differently in AWI photo's and Nca78 photo's.
I would like to build this but not certain how it is wired now

If you do like drawn on my post from July 7, it works.

[rmtucker]

@Nca78 said in 💬 Micro (nano) ampere meter (double):

@rmtucker said in 💬 Micro (nano) ampere meter (double):

I am confused the 1k resistors seem to be wired differently in AWI photo's and Nca78 photo's.
I would like to build this but not certain how it is wired now

If you do like drawn on my post from July 7, it works.

Are the blue and green resistors you have drawn on the back of the adc module the 1k resistors?
Have you soldered them on the other side?

[Nca78]

@rmtucker said in 💬 Micro (nano) ampere meter (double):

Are the blue and green resistors you have drawn on the back of the adc module the 1k resistors?
Have you soldered them on the other side?

Yes & yes.

[alexsh1]

@nca78 Exactly the same pin of the IC can be connected to the next pin (VCC) to change the refresh rate.

https://github.com/iforce2d/thrustTester/blob/master/README.md

[alexsh1]

I had some spare time and all parts so decided to assemble ampere meter.
Firstly, the sketch has to be changed. The lib Button.h does not exist (it has been renamed). It has to be changed to JC_Button.h. This has to be added to setup {}:

myBtn.begin();

in order for the button to work.

My question is this - reading are jumping like a yo-yo despite having a separate power supply (power bank). After calibration, reading maybe +30% or -30% off needless to say that its drifting dynamically. So constant current of 120uA is read +90 or +150 jumping up and down. Is this the way this meter is supposed to work?

[soroush_habibi]

Can you make a schematic of this circuit please?
I need this project.

[vidalv]

Hello, is there, somewhere, a real complete diagram of this project? This subject is interesting but not clearly documented ... It's a shame! Thank you.

[Enzo65]

Hi, pin A+ and pin B+ are connected together, on the same terminal block?

[metceyn]

@mfalkvidd If you have something related to this project, can you share it? (circuit schema or something)

[mfalkvidd]

@Metin-Can-AYAR sorry, I have nothing.

[Nca78]

@metceyn said in 💬 Micro (nano) ampere meter (double):

@mfalkvidd If you have something related to this project, can you share it? (circuit schema or something)

Hello, I will try to work again on this project in the coming days, I have made one years ago but reused (then broke !) the screen so it's not fonctional now. I will use another screen and make a functional one again as I will need it for some project.

[metceyn]

@Nca78 Thank you for your answer. I'm looking forward.

[metceyn]

@Nca78 Where do i attach the probes? How can i measure?