relay motion domoticz help

[floris]

Hi,

i ḿ trying to make my own sketch. using a sketch form domoticz.com has a working relay. i'm trying to implement a motion sensor with no luck so far. can anybody help me?
here s my sketch;

// Example sketch showing how to control physical relays.
// This example will remember relay state even after power failure.

#include <MySensor.h>
#include <SPI.h>

#define RELAY_1 4 // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 0 // GPIO value to write to turn on attached relay
#define RELAY_OFF 1 // GPIO value to write to turn off attached relay
#define CHILD_ID 1 // Id of the sensor child
#define DIGITAL_INPUT_SENSOR 3 // The digital input you attached your motion sensor. (Only 2 and 3 generates interrupt!)
#define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)

bool state;
bool value;

MySensor gw;
MyMessage msg(1,V_LIGHT);

void setup()
{
// Initialize library and add callback for incoming messages
gw.begin(incomingMessage, AUTO, true);
// Send the sketch version information to the gateway and Controller
gw.sendSketchInfo("RelayDoMoticz", "1.0");

// Fetch relay status
for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
// Register all sensors to gw (they will be created as child devices)
gw.present(sensor, V_LIGHT);
// Then set relay pins in output mode
pinMode(pin, OUTPUT);
// Set relay to last known state (using eeprom storage)
digitalWrite(pin, gw.loadState(sensor)?RELAY_ON:RELAY_OFF);
// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_TRIPPED);
gw.send(msg.set(value==HIGH ? 1 : 0));

  // Send the sketch version information to the gateway and Controller

gw.sendSketchInfo("Motion Sensor", "1.0");

pinMode(DIGITAL_INPUT_SENSOR, INPUT); // sets the motion sensor digital pin as input
// Register all sensors to gw (they will be created as child devices)
gw.present(CHILD_ID, S_MOTION);

}
}

void loop()
{
// Alway process incoming messages whenever possible
gw.process();
}

void incomingMessage(const MyMessage &message) {
// We only expect one type of message from controller. But we better check anyway.
if (message.type==V_LIGHT) {
// Change relay state
digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
// Store state in eeprom
gw.saveState(message.sensor, message.getBool());
// Write some debug info
Serial.print("Incoming change for sensor:");
Serial.print(message.sensor);
Serial.print(", New status: ");
Serial.println(message.getBool());
// Read digital motion value
boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH;

Serial.println(tripped);
gw.send(msg.set(tripped?"1":"0")); // Send tripped value to gw

}
}

[floris]

@floris I have got it working!!!!!using a motion/relay sketch from the forum.

Floris

[GizMoCuz]

it might be that this line

gw.present(sensor, V_LIGHT);

should be changed to

gw.present(sensor, S_LIGHT);

[dias]

hello, I search for a code for 2 pir sensor and relay 2
  it exists?

[Eme]

@floris can you post the final sketch you used? I am having the same issue.