Version 2.0 isn't working...

[mk55]

Everything was working fine, before I copied the new version to the arduino libraries
I tried the clear eeprom sketch without success.
When I try the pingpongsensors sketch I get this:

Starting sensor (RNNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
!TSP:ASSIGNID:FAIL (ID=0)
!TSM:FAILURE
TSM:PDT
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
!TSP:ASSIGNID:FAIL (ID=0)
!TSM:FAILURE
TSM:PDT
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:```

[tbowmo]

Have you updated both GW and node to 2.0.0? If I remember right, a node on 2.0.0 requires a GW on 2.0.0.

From the logs the node is trying to get a nodeid from GW.

[mk55]

I'm using the pingpongsensors sketch on both nodes

[AWI]

@mk55 You would still need the nodeid from the gateway.

[mk55]

@AWI Even when I try different sketches It just won't work...
Reverting back makes everything works again..
This what I get when I try 1 node with GatewaySerial sketch and 1 node with Relayactuator

TSM:FPAR
Starting repeater (RNNRA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
!TSP:ASSIGNID:FAIL (ID=0)
!TSM:FAILURE
TSM:PDT
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
!TSP:ASSIGNID:FAIL (ID=0)
!TSM:FAILURE
TSM:PDT
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:

[AWI]

@mk55 as @tbowmo mentioned the node is not getting an id. For me the new debug output is also not complete clear. It could indicate that you have a transmission problem. A way to find out is look at the debug output from both nodes.

[tekka]

@mk55 The issue here is, that the node has ID 0 which is not allowed, hence

!TSP:ASSIGNID:FAIL (ID=0)

How did you clear the EEPROM? It looks like you used the Arduino eeprom_clr example - this is not compatible with the MySensors setup. Instead, you should use the MySensors ClearEepromConfig.

Next step, if you do not have a controller that assigns ID, you can assign a static ID , e.g. 1, using

#define MY_NODE_ID 1

[mk55]

@tekka Omg tekka you're awsome!!
I did used the arduino eeprom_clr example, and when tried the ClearEepromConfig everything magically worked!
Thanks all!

[tekka]

@mk55 Excellent, happy to hear