Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

LCD Display Incorrect

markcaso last edited by

Re: Irrigation Controller (up to 16 valves with Shift Registers)

I have completed the project and have been bench testing it with My Vera. I can activate the zones via the Vera or from the push button on the irrigation controller. But the display isn't correct. Doesn't show the time, date, last water date, time left, etc just shows valve data and seq thru the #107, 207,307,407,507. I have it setup for 5 valves. Other wise the it works.
Reply Quote 0
1 Reply Last reply

1
Posts

667
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73900
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
Halloween Lights
My Project • led strip light ws2812b • • KevinT

1

3
Votes

1
Posts

24
Views

No one has replied
HVAC Controller
My Project • • Michael Link

3

1
Votes

3
Posts

28
Views

We are of like minds, Don't like the cloud based controls (that's another discussion). In my case I have a Bryant/Connex system, heat pump, variable speed fan and 4 zones. There's a lot going on: the 4 zones creates 16 profiles. The fan speed for a profile will depend on the indoor and outdoor temperature. The thermal fluid pump also has to be controlled. A profile will have an optimal air pressure, so there's a sensor there. The controller works just fine not being connected to the cloud. But I want to set the parameters remotely, Bryant/Connex can do this. I also wnat the status of the various actuators and sensors to show up in Home Assistant. The signals sent over the RS422 are proprietary. My plan was to reverse-engineer the signals. After doing this I'll have to experiment to get the right mix of air pressue, fan speed and thermal fluid flow for each profile. I'd like to do the same for my AO Smith heat pump water heater. I'd like to follow your progress. OSD
Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

2

2
Votes

2
Posts

35
Views

@Kokosnoot good solution. I remember the discussion in the early days of MySensors. I've powered the radio's for most of my sensors from the 3.3v regulator on the arduino board and for me that works perfect. But for my latest designs I decided to add a separate ams regulator for my radio's like the guys suggested in the beginning. Because you basically want the on board regulator to power the mcu only.
Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

5

3
Votes

5
Posts

15
Views

@OldSurferDude thank you !

LCD Display Incorrect

Suggested Topics

Welcome
Announcements • • hek

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Halloween Lights
My Project • led strip light ws2812b • • KevinT

HVAC Controller
My Project • • Michael Link

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

49
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

LCD Display Incorrect

Suggested Topics

Welcome Announcements • • hek

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

Halloween Lights My Project • led strip light ws2812b • • KevinT

HVAC Controller My Project • • Michael Link

Powering ESP8266 / NRF24L01 repeater through USB (improvement) My Project • • Kokosnoot

Water Filtering and Sterilization and Hot Water Recirculation My Project • • fsgraz

49Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Halloween Lights
My Project • led strip light ws2812b • • KevinT

HVAC Controller
My Project • • Michael Link

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

49
Online

11.4k
Users

11.1k
Topics

112.7k
Posts