Analog to digital how ?
-
Hi there,
I would like to know what and where i have to look for.
I reading with my nano 328 port A0, A1, A2 voltage from "3" motion senors
and get a specific value >700
if one of those ports gets above this 700
I would like to send this true mysensors as an normal motion sensor normal true trigger
but im not using any interrupt
How do i send this ?if (analogRead(A0) >=700)
{
send(msgmotion0.set(tripped0?"1":"0"));and for the others.
send(msgmotion0.set(tripped0?"1":"0"));
send(msgmotion1.set(tripped1?"1":"0"));
send(msgmotion3.set(tripped3?"1":"0"));
-
#define MY_RADIO_NRF24 #define MY_REPEATER_FEATURE #define MY_DEBUG //#include <SPI.h> #include <MySensors.h> boolean sensorUpperActive; boolean sensorBottomActive; boolean PIR00; #define MY_NODE_ID 30 #define CHILD_ID_PIR00 31 // Id of the sensor child #define CHILD_ID_PIR01 32 // Id of the sensor child #define CHILD_ID_PIR02 33 // Id of the sensor child void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("PIR Sensor", "4.0"); // Register all sensors to gw (they will be created as child devices) present(CHILD_ID_PIR00, S_MOTION, "PIR Sensor 0"); present(CHILD_ID_PIR01, S_MOTION, "PIR Sensor 1"); present(CHILD_ID_PIR02, S_MOTION, "PIR Sensor 2"); } // Initialize motion message MyMessage msgPIR00(CHILD_ID_PIR00, V_TRIPPED); MyMessage msgPIR01(CHILD_ID_PIR01, V_TRIPPED); MyMessage msgPIR02(CHILD_ID_PIR02, V_TRIPPED); // the setup routine runs once when you press reset: void setup() { // initialize serial communication at 9600 bits per second: // Serial.begin(9600); pinMode(LED_BUILTIN, OUTPUT); } // the loop routine runs over and over again forever: void loop() { Pir0lezen(); Pir1lezen(); Pir2lezen(); effopneer(); effneerop(); Tegelijk(); // delay(1000); // delay in between reads for stability } void Pir0lezen() { int PIR0 = analogRead(A0); if (analogRead(A0) >=700) { Serial.println("PIR0----"); Serial.println(PIR0); PIR00 = true; // Send status to Domoticz }} void Pir1lezen() { int PIR1 = analogRead(A1); if (analogRead(A1) >=700) { sensorBottomActive = true; // Send status to Domoticz Serial.println("PIR1----"); Serial.println(PIR1); }} void Pir2lezen() { int PIR2 = analogRead(A2); if (analogRead(A2) >=700) { sensorUpperActive = true; // Send status to Domoticz Serial.println("PIR2----"); Serial.println(PIR2); }} void effopneer() { if (sensorBottomActive==true && sensorUpperActive==false){ // do something digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level) delay(100); // wait for a second digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW sensorBottomActive = false ; Serial.println("PIR1--uit"); } } void effneerop() { if (sensorBottomActive==false && sensorUpperActive==true){ digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level) delay(500); // wait for a second digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW sensorUpperActive = false ; Serial.println("PIR2--uit"); } } void Tegelijk() { if (sensorBottomActive==true && sensorUpperActive==true){ digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level) delay(5000); // wait for a second digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW sensorUpperActive = false ; sensorBottomActive = false ; Serial.println("PIR1&2--uit"); } }
-
@Rene046 how about something like this?
void Pirlezen() { bool pir = analogRead(A0)>=700; send(msgmotion0.set(pir)); }}
-
Thx
I already got it running after a long night ...lol
here is what i have sofar...
#define MY_RADIO_NRF24 #define MY_REPEATER_FEATURE #define MY_DEBUG //#include <SPI.h> #include <MySensors.h> boolean sensorUpperActive; // boolean sensorBottomActive; int sensorBottomActive; int PIR1new; int PIR1old; int PIR2new; int PIR2old; boolean PIR00; #define MY_NODE_ID 30 #define CHILD_ID_PIR00 31 // Id of the sensor child #define CHILD_ID_PIR01 32 // Id of the sensor child #define CHILD_ID_PIR02 33 // Id of the sensor child void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("PIR Sensor", "4.0"); // Register all sensors to gw (they will be created as child devices) present(CHILD_ID_PIR00, S_MOTION, "PIR Sensor 0"); present(CHILD_ID_PIR01, S_MOTION, "PIR Sensor 1"); present(CHILD_ID_PIR02, S_MOTION, "PIR Sensor 2"); } // Initialize motion message MyMessage msgPIR00(CHILD_ID_PIR00, V_TRIPPED); MyMessage msgPIR01(CHILD_ID_PIR01, V_TRIPPED); MyMessage msgPIR02(CHILD_ID_PIR02, V_TRIPPED); // the setup routine runs once when you press reset: void setup() { // initialize serial communication at 9600 bits per second: // Serial.begin(9600); pinMode(LED_BUILTIN, OUTPUT); } // the loop routine runs over and over again forever: void loop() { Pir0lezen(); Pir1lezen(); Pir2lezen(); effopneer(); effneerop(); Tegelijk(); // delay(1000); // delay in between reads for stability } void Pir0lezen() { int PIR0 = analogRead(A0); if (analogRead(A0) >=700) { Serial.println("PIR0----"); Serial.println(PIR0); PIR00 = true; }} void Pir1lezen() { int PIR1new = analogRead(A1); if (PIR1new != PIR1old && PIR1new >=700) { sensorBottomActive = true ; send (msgPIR01.set(sensorBottomActive?"1":"0")); // Send status to Domoticz Serial.println("PIR1----"); Serial.println(PIR1new); PIR1old = PIR1new; }} void Pir2lezen() { int PIR2new = analogRead(A2); if (PIR2new != PIR2old && PIR2new >=700) { sensorUpperActive = true ; send (msgPIR02.set(sensorUpperActive?"1":"0")); // Send status to Domoticz Serial.println("PIR2----"); Serial.println(PIR2new); PIR2old = PIR2new; } } void effopneer() { if (sensorBottomActive==true && sensorUpperActive==false){ // do something digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level) delay(100); // wait for a second digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW sensorBottomActive = false ; send (msgPIR01.set(sensorBottomActive)); Serial.println("PIR1--uit"); } } void effneerop() { if (sensorBottomActive==false && sensorUpperActive==true){ digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level) delay(500); // wait for a second digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW sensorUpperActive = false ; send (msgPIR02.set(sensorUpperActive)); Serial.println("PIR2--uit"); } } void Tegelijk() { if (sensorBottomActive==true && sensorUpperActive==true){ digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level) delay(5000); // wait for a second digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW sensorUpperActive = false ; sensorBottomActive = false ; send (msgPIR01.set(sensorUpperActive)); send (msgPIR01.set(sensorBottomActive)); Serial.println("PIR1&2--uit"); } }
-
All working fine sometimes the pir reaction could be a bid faster, and sometimes i get a false reading think i'll have to put the pir signal lines to the ground with an resistor.
Any advice is welcome, to make thing faster, and less complex.
else use this with fun......#define MY_RADIO_NRF24 #define MY_REPEATER_FEATURE #define MY_DEBUG #include <Wire.h> // Wire library t.b.v. I²C #include <MySensors.h> byte GPIOA = 0x12; // GPIOA adres in 16-bit mode, is directe aansturing 1e groep van 8 I/O poorten. byte GPIOB = 0x13; // GPIOA adres in 16-bit mode, is directe aansturing 1e groep van 8 I/O poorten. boolean sensorBovenActive; // Status of Pir motion sensor 2. boolean sensorOnderActive; // Status of Pir motion sensor 1. boolean sensorKelderActive; // Status of Pir motion sensor 0. int PIR0new; // Pir motion sensor 0 updated value "Kelder". int PIR0old; // Pir motion sensor 0 old value "Kelder". int PIR1new; // Pir motion sensor 1 updated value "sensorOnderActive". int PIR1old; // Pir motion sensor 1 old value "sensorOnderActive". int PIR2new; // Pir motion sensor 2 updated value. "sensorBovenActive" int PIR2old; // Pir motion sensor 2 old value. sensorBovenActive" int StairDelay = 250; // Delay for stairs int StairOn = 30000; // Delay to keep stair light on #define MY_NODE_ID 30 #define CHILD_ID_PIR00 31 // Id of the sensor child #define CHILD_ID_PIR01 32 // Id of the sensor child #define CHILD_ID_PIR02 33 // Id of the sensor child void presentation(){ // Send the sketch version information to the gateway and Controller sendSketchInfo("Trap Controller", "4.0"); // Register all sensors to gw (they will be created as child devices) present(CHILD_ID_PIR00, S_MOTION, "PIR Sensor Kelder"); present(CHILD_ID_PIR01, S_MOTION, "PIR Sensor Trap Onder"); present(CHILD_ID_PIR02, S_MOTION, "PIR Sensor Trap Boven"); } // Initialize motion message MyMessage msgPIR00(CHILD_ID_PIR00, V_TRIPPED); MyMessage msgPIR01(CHILD_ID_PIR01, V_TRIPPED); MyMessage msgPIR02(CHILD_ID_PIR02, V_TRIPPED); // the setup routine runs once when you press reset: void setup() { Wire.begin(); // wake up I2C bus // set I/O pins to outputs Wire.beginTransmission(0x20); // Start adress of mcp23017 Wire.write(0x00); // IODIRA register Wire.write(0x00); // set all of port A to outputs Wire.endTransmission(); Wire.beginTransmission(0x20); Wire.write(0x01); // IODIRB register Wire.write(0x00); // set all of port B to outputs Wire.endTransmission(); } // the loop routine runs over and over again forever: void loop() { Pir0lezen(); Pir1lezen(); Pir2lezen(); effneerop(); effopneer(); effKelder(); } void Pir0lezen() { int PIR0new = analogRead(A0); if (PIR0new >=900) { sensorKelderActive = true; // Send status to Domoticz send (msgPIR00.set(sensorKelderActive?"1":"0")); Serial.println("PIR0new----"); Serial.println(PIR0new); PIR0old = PIR0new; sensorKelderActive = false; send (msgPIR00.set(sensorKelderActive)); }} void Pir1lezen() { int PIR1new = analogRead(A1); if (PIR1new != PIR1old && PIR1new >=710) { sensorOnderActive = true ; sensorBovenActive = false ; // Send status to Domoticz send (msgPIR01.set(sensorOnderActive?"1":"0")); Serial.println("PIR1----"); Serial.println(PIR1new); PIR1old = PIR1new; }} void Pir2lezen() { int PIR2new = analogRead(A2); if (PIR2new != PIR2old && PIR2new >=710) { sensorBovenActive = true ; sensorOnderActive = false ; // Send status to Domoticz send (msgPIR02.set(sensorBovenActive?"1":"0")); Serial.println("PIR2----"); Serial.println(PIR2new); PIR2old = PIR2new; }} void effopneer() { if (sensorOnderActive==true && sensorBovenActive==false){ Serial.println("PIR1--aan"); sensorOnderActive = false ; setLEDA(B01111111); // Tree 1 delay(StairDelay); setLEDA(B00111111); // Tree 2 delay(StairDelay); setLEDA(B00011111); // Tree 3 delay(StairDelay); setLEDA(B00001111); // Tree 4 delay(StairDelay); setLEDA(B00000111); // Tree 5 delay(StairDelay); setLEDA(B00000011); // Tree 6 delay(StairDelay); setLEDA(B00000001); // Tree 7 delay(StairDelay); setLEDA(B00000000); // Tree 8 delay(StairDelay); setLEDB(B01111111); // Tree 9 delay(StairDelay); setLEDB(B00111111); // Tree 10 delay(StairDelay); setLEDB(B00011111); // Tree 11 delay(StairDelay); setLEDB(B00001111); // Tree 12 delay(StairDelay); setLEDB(B00000111); // Tree 13 delay(StairDelay); setLEDB(B00000011); // Tree 14 send (msgPIR01.set(sensorOnderActive)); // switch off before delay delay(StairOn); setLEDA(B11111111); // all off setLEDB(B11111111); // all off Serial.println("PIR1--uit"); }} void effneerop() { if (sensorOnderActive==false && sensorBovenActive==true){ Serial.println("PIR2--aan"); sensorBovenActive = false ; setLEDB(B11111011); // Tree 14 delay(StairDelay); setLEDB(B11110011); // Tree 13 delay(StairDelay); setLEDB(B11100011); // Tree 12 delay(StairDelay); setLEDB(B11000011); // Tree 11 delay(StairDelay); setLEDB(B10000111); // Tree 10 delay(StairDelay); setLEDB(B00000011); // Tree 9 delay(StairDelay); setLEDA(B11111110); // Tree 8 delay(StairDelay); setLEDA(B11111100); // Tree 7 delay(StairDelay); setLEDA(B11111000); // Tree 6 delay(StairDelay); setLEDA(B11110000); // Tree 5 delay(StairDelay); setLEDA(B11100000); // Tree 4 delay(StairDelay); setLEDA(B11000000); // Tree 3 delay(StairDelay); setLEDA(B10000000); // Tree 2 delay(StairDelay); setLEDA(B00000000); // Tree 1 send (msgPIR02.set(sensorBovenActive)); delay(StairOn); setLEDA(B11111111); // all off setLEDB(B11111111); // all off Serial.println("PIR2--uit"); }} void effKelder() { } void setLEDA(byte value) { Wire.beginTransmission(0x20); Wire.write(GPIOA); // gpioa Wire.write(byte(value)); // set LEDs volgens waarde 'value' Wire.endTransmission(); } void setLEDB(byte value) { Wire.beginTransmission(0x20); Wire.write(GPIOB); // gpiob Wire.write(byte(value)); // set LEDs volgens waarde 'value' Wire.endTransmission(); } void bonuseff() { setLEDB(B11111011); // Tree 14 delay(StairDelay); setLEDB(B11110111); // Tree 13 delay(StairDelay); setLEDB(B11101111); // Tree 12 delay(StairDelay); setLEDB(B11011111); // Tree 11 delay(StairDelay); setLEDB(B10111111); // Tree 10 delay(StairDelay); setLEDB(B01111111); // Tree 9 delay(StairDelay); setLEDA(B11111110); // Tree 8 delay(StairDelay); setLEDA(B11111101); // Tree 7 delay(StairDelay); ; setLEDA(B11111011); // Tree 6 delay(StairDelay); ; setLEDA(B11110111); // Tree 5 delay(StairDelay); setLEDA(B11101111); // Tree 4 delay(StairDelay); setLEDA(B11011111); // Tree 3 delay(StairDelay); setLEDB(B10111110); // Tree 2 delay(StairDelay); setLEDB(B01111111); // Tree 1 delay(StairDelay); setLEDA(B10111111); // Tree 2 delay(StairDelay); setLEDA(B11011111); // Tree 3 delay(StairDelay); setLEDA(B11101111); // Tree 4 delay(StairDelay); setLEDA(B11110111); // Tree 5 delay(StairDelay); setLEDA(B11111011); // Tree 6 delay(StairDelay); setLEDA(B11111101); // Tree 7 delay(StairDelay); setLEDA(B11111110); // Tree 8 delay(StairDelay); setLEDB(B01111111); // Tree 9 delay(StairDelay); setLEDB(B10111111); // Tree 10 delay(StairDelay); setLEDB(B11011111); // Tree 11 delay(StairDelay); setLEDB(B11101111); // Tree 12 delay(StairDelay); setLEDB(B11110111); // Tree 13 delay(StairDelay); setLEDB(B11111011); // Tree 14 }```
