3. SmartSleep wake up message always get NACK

SmartSleep wake up message always get NACK

  • Henrik Nielsen

    Hi

    I'm struggling a bit with the smartSleep functionality in MySensors.

    I know it should be straight forward, since it appears that the usage of sleep and smartSleep methods are basically the same from a developers perspective, but for some reason, the "wake up" message the node sends when the smart sleep is over, never gets sent. I almost never see messages that I manually send with sensor data etc. getting NACK'ed, and this happens on every single wake.

    Below is a tiny PoC test I have made. I kept it as simple as possible so I could hopefully get something working, and build on to that. But this simple example also fails 😞

    #define MY_DEBUG
#define MY_RADIO_NRF24
#define MY_RF24_CHANNEL 0x44
#define MY_RF24_BASE_RADIO_ID 0x00, 0xf6, 0x4d,0x89, 0xc0
#include <MySensors.h>

void presentation() {
  sendSketchInfo("SmartSleepTest", "1.0");
  present(1, S_INFO, "Info");
}

void loop() {
  smartSleep(1000);
}

    When running, the output looks like this:

    6 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.0
26 TSM:INIT
28 TSF:WUR:MS=0
36 TSM:INIT:TSP OK
38 TSF:SID:OK,ID=204
40 TSM:FPAR
77 TSF:MSG:SEND,204-204-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
446 TSF:MSG:READ,202-202-204,s=255,c=3,t=8,pt=1,l=1,sg=0:2
452 TSF:MSG:FPAR OK,ID=202,D=3
573 TSF:MSG:READ,201-201-204,s=255,c=3,t=8,pt=1,l=1,sg=0:1
579 TSF:MSG:FPAR OK,ID=201,D=2
2084 TSM:FPAR:OK
2084 TSM:ID
2086 TSM:ID:OK
2088 TSM:UPL
2095 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2140 TSF:MSG:READ,0-201-204,s=255,c=3,t=25,pt=1,l=1,sg=0:2
2148 TSF:MSG:PONG RECV,HP=2
2150 TSM:UPL:OK
2152 TSM:READY:ID=204,PAR=201,DIS=2
2160 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2191 TSF:MSG:READ,0-201-204,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2201 TSF:MSG:SEND,204-204-201-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.0
2211 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:201
2355 TSF:MSG:READ,0-201-204,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2363 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=11,pt=0,l=14,sg=0,ft=0,st=OK:SmartSleepTest
2410 !TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=NACK:1.0
2420 TSF:MSG:SEND,204-204-201-0,s=1,c=0,t=36,pt=0,l=4,sg=0,ft=1,st=OK:Info
2428 MCO:REG:REQ
2441 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2506 TSF:MSG:READ,0-201-204,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2512 MCO:PIM:NODE REG=1
2514 MCO:BGN:INIT OK,TSP=1
2519 MCO:SLP:MS=1000,SMS=1,I1=255,M1=255,I2=255,M2=255
2529 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500
3037 TSF:TDI:TSL
3039 MCO:SLP:WUP=-1
3041 TSF:TRI:TSB
5457 !TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:1000
5466 MCO:SLP:MS=1000,SMS=1,I1=255,M1=255,I2=255,M2=255
5476 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=1,st=OK:500
5984 TSF:TDI:TSL
5986 MCO:SLP:WUP=-1
5988 TSF:TRI:TSB
8404 !TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:1000
8413 MCO:SLP:MS=1000,SMS=1,I1=255,M1=255,I2=255,M2=255
8423 TSF:MSG:SEND,204-204-201-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=1,st=OK:500
8931 TSF:TDI:TSL
8933 MCO:SLP:WUP=-1

    The PRE-SLEEP message at 2529 gets sent correct, but the POST-SLEEP message gets NACK'ed at 5457.

    I have tried the following, without any luck:

    1. Longer and shorter smart sleep durations, with the same result.

    2. Attempts has been made both with a Raspberry Pi gateway and an ESP8266 gateway, but I doubt the gateway type matter, since it looks like something locally on the node.

    3. Two types of hardware for the node, both a home-designed mini-pcb which run great for other nodes (without smart sleep), and the Easy/Newbie PCB from openhardware.io.

    4. Looking for examples that use smartSleep, but the ones I found only use sleep.

    ANY help or push in the right direction will be greatly appreciated. 🙂

    /Henrik

    0 Yveaux berkseo 2 Replies
  • Yveaux
    Mod

    @henrik-nielsen do you know if the message is received by the gateway? This is possible although the node reports nack.

    0
  • Henrik Nielsen

    @Yveaux I checked, and no, the gateway does not receive the wake up message with payload 1000. It does receive the pre-sleep message with 500 ms, so I'm pretty sure I'm looking the right place 🙂

    0 berkseo 1 Reply
  • berkseo

    @henrik-nielsen
    Hello, there may be a problem with the repeater. ACK and NOACK are confirmation of sending to the first node in the chain(that is, in your case to the repeater). Try turning off this repeater so that the sender receives a new route. I also recommend using the sleep function with the attribute of smart sleep mode activation -- sleep(1000, true);

    1
  • berkseo

    @henrik-nielsen
    Try adding a little wait after the line with sleep, it will slow down the sketch but the framework will continue to work wait(200); ...not sure.

    0
  • Henrik Nielsen

    @berkseo Thank you for your suggestions, I have tried both.

    • I moved the node up right next to the gateway, so there are no repeaters in between. I still get NACK on the wake up message. And I can see in the gateway log that the wake up message are not received by the gateway. The other message still shows up just fine. In the output below you can see it sends directly to node 0

    • I also added a wait(200) after the sleep, still get the same error, but I guess it is because the wake up message are sent before the sleep method returns?

    • Using sleep(1000, true) instead of smartSleep, same result, but I'll start using sleep(nnn, true) instead anyway 🙂

    New code:

    #define MY_DEBUG
#define MY_RADIO_NRF24
#define MY_RF24_CHANNEL 0x44
#define MY_RF24_BASE_RADIO_ID 0x00,0xf6,0x4d,0x89,0xc0
#include <MySensors.h>

void presentation() {
  sendSketchInfo("SmartSleepTest", "1.0");
  present(1, S_INFO, "Info");
}

void loop() {
  sleep(1000, true);
  wait(200);
}

    Output:

    16 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.0
26 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSF:SID:OK,ID=204
38 TSM:FPAR
75 TSF:MSG:SEND,204-204-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
686 TSF:MSG:READ,0-0-204,s=255,c=3,t=8,pt=1,l=1,sg=0:0
692 TSF:MSG:FPAR OK,ID=0,D=1
708 TSF:MSG:READ,0-201-204,s=255,c=3,t=25,pt=1,l=1,sg=0:2
714 !TSF:MSG:PONG RECV,INACTIVE
854 TSF:MSG:READ,202-202-204,s=255,c=3,t=8,pt=1,l=1,sg=0:1
880 TSF:MSG:READ,203-203-204,s=255,c=3,t=8,pt=1,l=1,sg=0:1
2084 TSM:FPAR:OK
2084 TSM:ID
2086 TSM:ID:OK
2088 TSM:UPL
2093 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2101 TSF:MSG:READ,0-0-204,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2107 TSF:MSG:PONG RECV,HP=1
2109 TSM:UPL:OK
2111 TSM:READY:ID=204,PAR=0,DIS=1
2117 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2127 TSF:MSG:READ,0-0-204,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2136 TSF:MSG:SEND,204-204-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.0
2146 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2242 TSF:MSG:READ,0-0-204,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2254 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=11,pt=0,l=14,sg=0,ft=0,st=OK:SmartSleepTest
2265 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
2275 TSF:MSG:SEND,204-204-0-0,s=1,c=0,t=36,pt=0,l=4,sg=0,ft=0,st=OK:Info
2283 MCO:REG:REQ
2289 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2297 TSF:MSG:READ,0-0-204,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2304 MCO:PIM:NODE REG=1
2308 MCO:BGN:INIT OK,TSP=1
2310 MCO:SLP:MS=1000,SMS=1,I1=255,M1=255,I2=255,M2=255
2318 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500
2826 TSF:TDI:TSL
2828 MCO:SLP:WUP=-1
2830 TSF:TRI:TSB
4513 !TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:1000
4722 MCO:SLP:MS=1000,SMS=1,I1=255,M1=255,I2=255,M2=255
4728 TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=1,st=OK:500
5238 TSF:TDI:TSL
5240 MCO:SLP:WUP=-1
5242 TSF:TRI:TSB
6926 !TSF:MSG:SEND,204-204-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:1000
    0 berkseo 1 Reply
  • berkseo

    @henrik-nielsen
    😞

    The problem is deeper, you came across an interesting point, I did not notice it before... left to dig the problem

    0
  • Henrik Nielsen

    I guess if I could just turn off the wake up / post-sleep message, everything would still kinda work. MyController will react to the pre-sleep message and send any pending messages, so the problem is just the 2 seconds of wasted battery everytime it try to send the wake up messages.

    There might of course be other implications that I am not aware of 🙂

    0 berkseo 1 Reply
  • berkseo

    @henrik-nielsen
    I banished your sketch. Faced the same problem, have not seen before. As it turned out, this is a problem of quality of radio modules and radio driver settings. The solution is described below.

    Was before:

    
 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.1-alpha

18 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.1-alpha
28 TSM:INIT
28 TSF:WUR:MS=0
36 TSM:INIT:TSP OK
38 TSF:SID:OK,ID=100
40 TSM:FPAR
77 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
600 TSF:MSG:READ,0-0-100,s=255,c=3,t=8,pt=1,l=1,sg=0:0
606 TSF:MSG:FPAR OK,ID=0,D=1
2088 TSM:FPAR:OK
2088 TSM:ID
2091 TSM:ID:OK
2093 TSM:UPL
2099 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2205 TSF:MSG:READ,0-0-100,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2211 TSF:MSG:PONG RECV,HP=1
2215 TSM:UPL:OK
2217 TSM:READY:ID=100,PAR=0,DIS=1
2222 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2357 TSF:MSG:READ,0-0-100,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2365 TSF:MSG:SEND,100-100-0-0,s=255,c=0,t=17,pt=0,l=11,sg=0,ft=0,st=OK:2.3.1-alpha
2375 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2838 TSF:MSG:READ,0-0-100,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2846 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=11,pt=0,l=14,sg=0,ft=0,st=OK:SmartSleepTest
2856 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
2867 TSF:MSG:SEND,100-100-0-0,s=1,c=0,t=36,pt=0,l=4,sg=0,ft=0,st=OK:Info
2875 MCO:REG:REQ
2912 !TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=NACK:2
4923 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=1,st=OK:2
4995 TSF:MSG:READ,0-0-100,s=255,c=3,t=27,pt=1,l=1,sg=0:1
5001 MCO:PIM:NODE REG=1
5003 MCO:BGN:STP
5005 MCO:BGN:INIT OK,TSP=1
6008 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
6017 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
6625 TSF:TDI:TSL
6627 MCO:SLP:WUP=-1
6629 TSF:TRI:TSB
8312 !TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:3000
10524 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
10532 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=1,st=OK:600
11141 TSF:TDI:TSL
11143 MCO:SLP:WUP=-1
11145 TSF:TRI:TSB
12828 !TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:3000
15036 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
15044 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=1,st=OK:600
15652 TSF:TDI:TSL

    1.Go to the folder - C:\Users\Andrey\Documents\Arduino\libraries\MySensors-development

    2.Next, go to the folder - \drivers\RF24

    3.Open the file - RF24registers.h

    4.Change the parameters to these:
    ...lines 42-47.

    // ARD, auto retry delay

    #define RF24_SET_ARD (10)
    // ARD, auto retry count

    #define RF24_SET_ARC (15)

    5.Next, open the file-RF24.ccp
    Change the parameters to these:
    ...line 67
    ...line 114

    delayMicroseconds(100);

    The problem in radio driver, in his settings, apparently all wrote according to the Datasheet, but in life a bit otherwise)))

    Has now become:

     
 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.1-alpha

18 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.1-alpha
28 TSM:INIT
28 TSF:WUR:MS=0
38 TSM:INIT:TSP OK
43 TSF:SID:OK,ID=100
45 TSM:FPAR
102 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2111 !TSM:FPAR:NO REPLY
2113 TSM:FPAR
2170 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2736 TSF:MSG:READ,0-0-100,s=255,c=3,t=8,pt=1,l=1,sg=0:0
2742 TSF:MSG:FPAR OK,ID=0,D=1
4182 TSM:FPAR:OK
4182 TSM:ID
4184 TSM:ID:OK
4186 TSM:UPL
4194 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
4300 TSF:MSG:READ,0-0-100,s=255,c=3,t=25,pt=1,l=1,sg=0:1
4306 TSF:MSG:PONG RECV,HP=1
4311 TSM:UPL:OK
4311 TSM:READY:ID=100,PAR=0,DIS=1
4319 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
4450 TSF:MSG:READ,0-0-100,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
4462 TSF:MSG:SEND,100-100-0-0,s=255,c=0,t=17,pt=0,l=11,sg=0,ft=0,st=OK:2.3.1-alpha
4474 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4939 TSF:MSG:READ,0-0-100,s=255,c=3,t=6,pt=0,l=1,sg=0:M
4950 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=11,pt=0,l=14,sg=0,ft=0,st=OK:SmartSleepTest
4966 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4976 TSF:MSG:SEND,100-100-0-0,s=1,c=0,t=36,pt=0,l=4,sg=0,ft=0,st=OK:Info
4984 MCO:REG:REQ
5021 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
5308 TSF:MSG:READ,0-0-100,s=255,c=3,t=27,pt=1,l=1,sg=0:1
5314 MCO:PIM:NODE REG=1
5316 MCO:BGN:STP
5318 MCO:BGN:INIT OK,TSP=1
6322 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
6334 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
6942 TSF:TDI:TSL
6944 MCO:SLP:WUP=-1
6946 TSF:TRI:TSB
6952 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=OK:3000
9164 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
9177 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
9785 TSF:TDI:TSL
9787 MCO:SLP:WUP=-1
9789 TSF:TRI:TSB
9797 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=OK:3000
12005 MCO:SLP:MS=3000,SMS=1,I1=0,M1=3,I2=255,M2=255
12017 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:600
12625 TSF:TDI:TSL

    use.. 😉

    1
  • Henrik Nielsen

    It works 😄 You're a wizard @berkseo 🙂

    I do infact use the cheap radio modules from china, so I think you're right about the possible lacking of quality in the hardware 😕

    I guess there is not a way I can change these settings somewhere local to my sketch, so they do not get overwritten the next time I update the MySensors lib?

    Anyway, it's great that it works now, and I will just bookmark this topic for future reference.

    Thank again for your assistance 🙂

    0 berkseo 1 Reply
  • berkseo

    @henrik-nielsen
    Everyone uses cheap radio modules, it's a reality. One thing is technical specifications, the other is real network on real equipment. Although I think if you take a very original radios, it will be the same in 99%)). ....Glad to help, it's called a community.

    1 Henrik Nielsen 1 Reply
  • Henrik Nielsen

    @berkseo I just started wondering if "everyone" uses cheap chinese radios, should this fix be part of the official code base?

    Maybe just as something that could be enabled if needed.

    0 scalz 1 Reply
  • scalz
    Hardware Contributor

    @henrik-nielsen said in SmartSleep wake up message always get NACK:

    if "everyone" uses cheap chinese radios, should this fix be part of the official code base?

    simple! add issue or pull request to mysensors github. that's the easiest way when there's issue to fix 😉
    because the team can't follow all forum topics and make todolist, in this way this is not handy.

    0 berkseo 1 Reply
  • berkseo

    @scalz said in SmartSleep wake up message always get NACK:

    pull request

    I made a pull request. I think that this will accept. Apparently the next version will already be. ...I'm not sure this is absolutely perfect, a mistake in the first message after sleeping mostly. Perhaps later it is better to modify startListening, although, of course, now it is a good solution, but not ideal.

    1 Henrik Nielsen Memphis007 2 Replies
  • Henrik Nielsen

    @berkseo Great 🙂 I am currently trying to figure out what my employers policy for open source contributions made in their employees spare time is, so I could make the pull request myself, but you beat me to it 😞

    1
  • Memphis007

    @berkseo Hi, could you post the link to your pull request ? I don't see any traces of it in MySensors Github repository.

    BTW with my setup (genuine/good quality NRF24L01) increase lines 67 & 114 of RF24.ccp to 50 do the trick.

    Thanks.

    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @memphis007 berseo's pull requests (link 1, link 2) were closed in favor of this pull request.

    0
  • Memphis007

    @mfalkvidd I have applied Tekka007 pull request successfully, all is working correctly now. Thanks !

    1
Log in to reply
 

Suggested Topics

55
Online

11.4k
Users

11.1k
Topics

112.7k
Posts



Copyright 2019 Sensnology   |   Forum Guidelines   |   Privacy Policy   |   Terms of Service