Small wall outlet sensor node

[RJ_Make]

@axillent Your an evil genius! :-)

[axillent]

@ServiceXp thanks)
all this is simple, just a patient work

Printed thing is a bit ugly comparing to the virtual one, but it's work is real

http://www.youtube.com/watch?v=JG7gutD1oo8

[gregl]

@axillent So very very cool!!

as @gadu commented, making one at 90 deg so its very low profile would be even better for places such as hallways where the sensor could be bumped....

Really nice!

[blacey]

@axillent - well done! :+1:

[bjornhallberg]

@axillent Very impressive! What is the total cost of the components involved?

[axillent]

@bjornhallberg it is hard to say
the BOM is simple and short
but the cost of a single component is dramatically depends on how many your purchase in a single order
for example atmega328 purchased in 10pcs will be US1.2 pcs while a single pcs will costs US3-4

If it will be an interest I think in production this PCB can cost retail US8-12

[gigi]

@axillent
very very cool!!

[nutcracker]

Impressive!

[axillent]

made two more with modified box - it is a bit wider to hold DHT sensor inside
I made a new sketch as a combination of Dalas example and DHT. This new sketch able to detect automatically connected sensors and work according to detection.

One problem I've got. I cannot get DHT working from AC plug. It is working fine been powered from DC and failed during startup been powered from AC :( The most probably the reason is high pulsation (up to 440mV) coming from the supply based on SR10 chip.
Dalas is fine with this but not DHT. Probably some code inside the library holds.

Had to mark each sensor with radio channel because they will work with different gateways

[sharath krishna]

really cool :) what are u using to convert the AC-DC ? how u doing it ?

[axillent]

@sharath-krishna thanks

yearly in this thread you can find a schematics.
I'm using here SR10. Many alternatives were discussed here http://forum.mysensors.org/topic/687/230v-power-supply-to-arduino

I've found a solution to my problem with DHT. I put delay(500) at the beginning of setup().
This is needed to stabilize DC before initializing DHT.
Alternatively a 4.7uF capacitor can be connected between RESET and GND

[axillent]

This is my combined sketch with automatic detection of connected many DS18B20 and DHT11/22

#define RADIO_CHANNEL		76

#define DS18B20_PIN			A0
#define DS18B20_MAX_SENSORS	8
#define DHT_PIN				A5
#define LED_PIN				5
#define SLEEP_TIME_SEC		60

#include <avr/wdt.h>
#include <avr/interrupt.h>
#include <avr/sleep.h>

#include <MySensor.h>
#include <SPI.h>
#include <DallasTemperature.h>
#include <OneWire.h>
#include <DHT.h>

// DS18B20
OneWire oneWire(DS18B20_PIN);
DallasTemperature	sensors(&oneWire);

MyMessage msgHum(0, V_HUM);
MyMessage msgTemp(0, V_TEMP);

struct {
	struct {
		uint8_t	count;
		float	lastTemperature[DS18B20_MAX_SENSORS];	
	} ds18b20;
	struct {
		DHT		sensor;
		uint8_t	count;
		float lastTemp;
		float lastHum;
	} dht;
	MySensor gw;
} var;

ISR(WDT_vect) {
}

void setup()
{
	wdt_disable();
	//delay(500);

	pinMode(LED_PIN, OUTPUT);
	digitalWrite(LED_PIN, HIGH);

	// init mysensors
	var.gw.begin(NULL, AUTO, false, AUTO, RF24_PA_LEVEL,RADIO_CHANNEL);

	// init dalas
	sensors.begin();
	var.ds18b20.count = sensors.getDeviceCount();
	if(var.ds18b20.count > DS18B20_MAX_SENSORS) var.ds18b20.count = DS18B20_MAX_SENSORS;

	// init dht
	digitalWrite(LED_PIN, LOW);
	var.dht.sensor.setup(DHT_PIN);
	float temperature = var.dht.sensor.getTemperature();
	var.dht.count = (isnan(temperature))?0:1; 

	var.gw.sendSketchInfo("WallCombined", "1.0");

	// present ds18b20
	for (int i=0; i<var.ds18b20.count; i++) {
		var.gw.present(i+2, S_TEMP);
	}
	if(var.dht.count) {
		var.gw.present(0, S_HUM);
		var.gw.present(1, S_TEMP);		
	}
	var.gw.debugPrint(PSTR("Init of combined sensor: %d ds18b20 sensors, %d dht sensors\n"), var.ds18b20.count, var.dht.count);
	for(int i=0; i < var.ds18b20.count + var.dht.count; i++) {
		digitalWrite(LED_PIN, LOW);
		delay(500);
		digitalWrite(LED_PIN, HIGH);
		delay(1000);
	}
}

void loop()
{
	// Process incoming messages (like config from server)
	var.gw.process();

	// Fetch temperatures from Dallas sensors
	if(var.ds18b20.count) sensors.requestTemperatures();

	// Read temperatures and send them to controller
	for (int i=0; i<var.ds18b20.count; i++) {
  
		// Fetch and round temperature to one decimal
		float temperature = static_cast<float>(static_cast<int>((var.gw.getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
  
		// Only send data if temperature has changed and no error
		if (var.ds18b20.lastTemperature[i] != temperature && temperature != -127.00) {
	  
			// Send in the new temperature
			var.gw.send(msgTemp.setSensor(i+2).set(temperature,1));
			var.ds18b20.lastTemperature[i]=temperature;
		}
	}

	if(var.dht.count) {
		boolean metric = var.gw.getConfig().isMetric;
		float temperature = var.dht.sensor.getTemperature();
	
		if (isnan(temperature)) {
			var.gw.debugPrint(PSTR("Failed reading temperature from DHT\n"));
		} else if (temperature != var.dht.lastTemp) {
			var.dht.lastTemp = temperature;
			if (!metric) {
				temperature = var.dht.sensor.toFahrenheit(temperature);
			}
			var.gw.send(msgTemp.setSensor(1).set(temperature, 1));
		}

		float humidity = var.dht.sensor.getHumidity();
		if (isnan(humidity)) {
			var.gw.debugPrint(PSTR("Failed reading humidity from DHT"));
		} else if (humidity != var.dht.lastHum) {
			var.dht.lastHum = humidity;
			var.gw.send(msgHum.setSensor(0).set(humidity, 1));
		}
	}

	digitalWrite(LED_PIN, HIGH);
	delay(5000);
	digitalWrite(LED_PIN, LOW);
	delay(500);

	// sleep
	Serial.flush();
	var.gw.powerDown();

	for(int wdt_count=SLEEP_TIME_SEC; wdt_count > 0; wdt_count--) {
		wdt_enable(WDTO_1S);
		WDTCSR |= (1 << WDIE);
		set_sleep_mode(SLEEP_MODE_PWR_DOWN);
		sleep_enable();
		sei();
		sleep_cpu();
		sleep_disable();
	}

	wdt_disable();
}

[axillent]

3D models are published here http://www.thingiverse.com/thing:688442

[BulldogLowell]

@axillent said:

3D models are published here http://www.thingiverse.com/thing:688442

nice job

can you tell us what kind of 3D printer you are using, and if you are happy with it.

I have a lot of electronics, and not a lot of housings.... I'm thinking about jumping in!

[axillent]

@BulldogLowell I'm using Makerbot Replicator 2 for more than 2 years

I have nothing to compare with. But it gives the possibilities I never have.
From hardware side I had to fix some problems Replicator 2 is having. New models I hope is more sufficient.
Makerbot is progressing, at least an improvement on software side is essential.

Today you will find many brands and many models to choose from.

[Jan Gatzke]

@axillent How do you upload the sketch? Do you solder in a preprogrammed atmega or are there connectors on the board? The DHT needs only 1.5 mA. Wouldn't it be possible to supply this with an digital out pin of the atmega? This way you could delay the power up process.

[bjornhallberg]

Just a fair warning for anyone considering a new ("5th generation") Makerbot Replicator. Check up on some reviews before getting one. Things have apparently gone downhill since the good old days. Extruders don't last as long etc. If anyone is willing to pay the sort of price that Makerbot is asking there are better alternatives.
http://nicklievendag.com/makerbot-replicator-5th-generation-review/

Also, the Makerbot software is painfully slow compared to most alternatives.
http://nicklievendag.com/simplify3d-vs-makerbot-desktop/
http://www.fabbaloo.com/blog/2014/7/20/hands-on-with-simplify3d
Not that I endorse Simplify3D. There are free / open-source alternatives that are just as fast.

Finally, I'm skeptical about the legal details surrounding Thingiverse.

[axillent]

@Jan-Gatzke originally a pre-loaded MCU were soldered but later I solder on top of the PCB a 6 pin ISP connectors
There is no need to source DHT from the MCU pin, it is simple to put delay at the beginning of setup or use highest startup time by fuses (my choice)

the original idea is to use pogopin connector, but I've just ordered them and not yet received. I need a very small footprint ISP connector for Mysensors devices

@bjornhallberg said:

Just a fair warning for anyone considering a new ("5th generation") Makerbot Replicator. Check up on some reviews before getting one.

have no experience with 5th generation but fully agree with you that there are many alternatives

Also, the Makerbot software is painfully slow compared to most alternatives.

it is not true. I'm very satisfied with the performance of the software.
I do not believe that someone can be faster than instantaneous

Finally, I'm skeptical about the legal details surrounding Thingiverse.

what kind of issues?

[bjornhallberg]

@axillent said:

Also, the Makerbot software is painfully slow compared to most alternatives.

it is not true. I'm very satisfied with the performance of the software.
I do not believe that someone can be faster than instantaneous

I meant slicing speeds on very complex models specifically. But it would not surprise me if the print quality / toolpaths created are better with competing software as well.

Finally, I'm skeptical about the legal details surrounding Thingiverse.

what kind of issues?

Like Facebook and other big corporations where they basically own the data you upload and store on their servers.

Oh, also, bonus points to Makerbot / Stratasys for actually stealing technology and incorporating it into their own designs:
http://3dprintingindustry.com/2014/05/28/makerbot-become-takerbot/

Bottom line, your Replicator 2 is in many ways better than the current line-up from Makerbot. Mostly because the extruder will last you many thousands of hours and not just 200-500 or whatever they guarantee these days when people come complaining.

The biggest joke is perhaps their massive Z18 printer, which costs a fortune, puts out dismal results (at least without a ton of tweaking if at all possible), can't handle ABS and is really slow. Plus having the same lousy extruder. I mean, 200 hours on the Z18 could translate into just 10 reasonably big print jobs. They actually got one at my local Makerspace. :dizzy_face: They could have gotten two ordinary printers for the price of that one ...

[axillent]

@bjornhallberg bad to know that new models are worse

actually had no plans to upgrade. For the nearest feature I'm fine with Repl2.
it is also important that I made a required tuning and able to recover many things by myself
already have an experience and know what to expect

I do not think my models complicated but the slicing speed was improved by handred times in the first year of the purchase
today i have to wait almost none before printing starts

what is even more important - raft support was improved revolutionary. Before it was sucks to print surface on the raft - it became ugly and unacceptable as a from panel. Now all are very different