So after the "success" ;( of my previous design "simple relay actuator" i did another one for roller shutter/cover device Simple cover actuator

Main goals were:

1. Simple design (NO SMT) all throe hole
2. Safe, AC-DC, fuses, creepage etc...
3. Cheap, no expensive hardware
4. Easy to build, anyone could do it

Main Components:

• Hi-Link AC-DC PSU
• 2 relay design one for power one for direction
• Atmega328p-pu
• nrf24l-01 radio

IT works very well for me with my Home Assistant controller HA, i am using time to set its position nothing too complicated.

Again, please comment and ask questions as you wish, thanks for the great feedback this forum is the best.

Since i dont think humans should solder SMT devices i made this nice little non SMT board with 3 SSR relays, Hi-Link power supply, atmega328P and separated fuses for PSU and load, in a 5X5 CM board.
So far its working great, i did not put a temp fuse in the design mainly because i dont see any commercial in wall units using one, so for me i think its safe enough to not use it.
I would appreciate your comments on it, Thanks.
Main goals are:

• No SMT
• 5X5 CM board
• Safe for in wall use
• Simple and cheep

Top side design:

Bottom side design:

https://github.com/home-assistant/home-assistant.github.io/pull/1484

@Boots33 i could not make the NRF2401+ work with the le33 i moved to lm117 or 662k and it works, just wasn't enough juice...

@artipi Sure you can that is the whole point of the D5, D6, D7 connection.

You just need to take the GND and each of these digital inputs and connect them to the switch (NO high voltage in the switch only GND and digital input), each one of then controls one relay.

I just wrap it with wet toilet paper, works every time.

You need to build it using few nodes, something like this:

Explain:
the "Clock" node is giving the current hour, the "Constant" nodes are the range of hours, the "Check in Range" node will output a 1 only when the hour is in the range.
Then you have a AND with the "Door" switch and after you have AND with the "Light" switch.
Result - light will be on only if time is in range and door is on and light is on.

This is how i would do it i dont know if there is any easier way other then writing your own custom node, you said you are a .NET programmer so it shouldn't be hard.
Writing few custom nodes my self i can tell its very straight forward.

@Nca78 yes it is YB1FA

Small update, i connected touch switches to the board instead of mechanical switches.
where i live we are using gwiss switches and when the board is in the box there is not much room for mechanical switches as they are too deep, so i took some blanks that are used to cover unused switch hols and added touch switch to it, see the pictures below:

So i ended up implementing it in my own library, still under tests, i will publish it here once i push it to github.

@gryzli133 Sorry but i dont know how to debug Domoticz

@gryzli133 Its tested and working on Homeassistant, you will probably will have to modify the code to make it work with other controllers, let me know if you need help with that.

@hummeruli
for #1 try switching also these variables:
#define DIRECTION_DOWN 1
#define DIRECTION_UP 0

for #2 can you send debug output?

@hummeruli can you check "Show verbose output during: " for compilation in the Preferences page and send me the detailed compilation log?

@hummeruli It compiles just fine on my machine, what version of mysensors do you have? i am using v2:

@hummeruli its here:
https://forum.mysensors.org/topic/7386/mysensors-cover-node

@gryzli133 No, Sorry. Let us know if you make it happen.

@gryzli133 The only way i can see is using the radio pins 9, 10, 11, 12, 13 if they can be used with RS485 or i2c then you are good to go

@Lucien Sorry for the delay, i will post it soon.

I just wrap it with wet toilet paper, works every time.