Works like a charm...

Thanks for sharing :)

Thanks for your answer.

I double check my wires, and found that my capacitor 4.7uF wasn't in the right place. I modified it, delete my sensor on Vera and Include it again and It works.

thanks.

Hello,

I want to include a motion sensor, but after inclusion, the sensor is not well recognized. It shows me the generic node :

 urn:upnp-arduino-cc:serviceId:arduinonode1

The communication seams to be OK, because in the Vera log I get that when I push the init button on my sensor :

50      05/08/15 17:20:43.016   luup_log:59: Arduino: Presentation: 1;255;0;0;17;1.4.1 <0x2da45680>
50      05/08/15 17:20:43.016   luup_log:59: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,ArduinoLibVersion, 1.4.1, 61 <0x2da45680>
50      05/08/15 17:20:43.018   luup_log:59: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdate, 1431098443, 61 <0x2da45680>
50      05/08/15 17:20:43.039   luup_log:59: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdateHR, 17:20, 61 <0x2da45680>
50      05/08/15 17:20:43.040   luup_log:59: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,RelayNode, 0, 61 <0x2da45680>
50      05/08/15 17:20:43.040   luup_log:59: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,RelayNodeHR, GW, 61 <0x2da45680>
50      05/08/15 17:20:43.041   luup_log:59: Arduino: Sending: 1;255;3;0;6;M <0x2da45680>
50      05/08/15 17:20:45.042   luup_log:59: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,SketchName, Motion Sensor, 61 <0x2da45680>
50      05/08/15 17:20:45.044   luup_log:59: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,SketchVersion, 1.1, 61 <0x2da45680>

My sensor send data to my Vera and the Vera catch them :

50      05/08/15 17:21:14.536   luup_log:59: Arduino: Set variable: 1;2;1;0;16;0 <0x2da45680>
50      05/08/15 17:21:21.143   luup_log:59: Arduino: Set variable: 1;2;1;0;16;1 <0x2da45680>
(...)

I read somewhere that in the gateway I should add I_Arduino1.xml into impl_file property but It has been always here.

Regards,

Hello,

I had the same issue and the root cause was my powersupply, it was not enought powerfull. I power my arduino with 12V and everything goes well.

Regards,

Hello,

I had the same problems and I solved it by using an external 12V power supply created with a RAC02-12SC from RECOM Powersupply.

Regards

Hello Experts,

I'm new in arduino and MySensors stuff.

I want to build my Ethernet Gateway. I did it with Arduino Nano V3 (Nano DCCduino MEGA 328p) and the Ethernet ENC28J60.

My problem is when I connect my ethernet cable, the ethernet LED didn't blink as normal. Furthermore, when I measure the voltage on the board I see 2.28V not 3,3V.

Am I the only one who has this issue ?

PS: sorry for my english.

Regards