P1 not working when using Mysensors ?

Toine33

Hey guys,

I am trying to make this sketch work for a few days now but it looks like it wont work in combination with Mysensors.
Here the sketch without the Mysensors.
I am receiving output of the P1 Port on hardware serial 2.


#define MY_DEBUG

//#define MY_RADIO_RF24
//#include <MySensors.h>



char c;
 
void setup() {
 Serial.begin(19200);
  Serial2.begin(9600, SERIAL_7N1);
}
 
void loop() {
    if (Serial2.available()) {
        c = Serial2.read();

    Serial.print(c);
    }
}





/* Baud-rates available: 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, or 115200, 256000, 512000, 962100
 *  
 *  Protocols available:
 * SERIAL_5N1   5-bit No parity 1 stop bit
 * SERIAL_6N1   6-bit No parity 1 stop bit
 * SERIAL_7N1   7-bit No parity 1 stop bit
 * SERIAL_8N1 (the default) 8-bit No parity 1 stop bit
 * SERIAL_5N2   5-bit No parity 2 stop bits 
 * SERIAL_6N2   6-bit No parity 2 stop bits
 * SERIAL_7N2   7-bit No parity 2 stop bits
 * SERIAL_8N2   8-bit No parity 2 stop bits 
 * SERIAL_5E1   5-bit Even parity 1 stop bit
 * SERIAL_6E1   6-bit Even parity 1 stop bit
 * SERIAL_7E1   7-bit Even parity 1 stop bit 
 * SERIAL_8E1   8-bit Even parity 1 stop bit 
 * SERIAL_5E2   5-bit Even parity 2 stop bit 
 * SERIAL_6E2   6-bit Even parity 2 stop bit 
 * SERIAL_7E2   7-bit Even parity 2 stop bit  
 * SERIAL_8E2   8-bit Even parity 2 stop bit  
 * SERIAL_5O1   5-bit Odd  parity 1 stop bit  
 * SERIAL_6O1   6-bit Odd  parity 1 stop bit   
 * SERIAL_7O1   7-bit Odd  parity 1 stop bit  
 * SERIAL_8O1   8-bit Odd  parity 1 stop bit   
 * SERIAL_5O2   5-bit Odd  parity 2 stop bit   
 * SERIAL_6O2   6-bit Odd  parity 2 stop bit    
 * SERIAL_7O2   7-bit Odd  parity 2 stop bit    
 * SERIAL_8O2   8-bit Odd  parity 2 stop bit    
*/

When i am using this same sketch with the Mysensors it is not giving output anymore.
Does someone has an clue ?
I have used an Arduino nano 16mhz first on altsoftserial with the same result.
in this example i am using an Arduino mega 2560.


#define MY_DEBUG

#define MY_RADIO_RF24
#include <MySensors.h>



char c;
 
void setup() {
 Serial.begin(19200);
  Serial2.begin(9600, SERIAL_7N1);
}
 
void loop() {
    if (Serial2.available()) {
        c = Serial2.read();

    Serial.print(c);
    }
}





/* Baud-rates available: 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, or 115200, 256000, 512000, 962100
 *  
 *  Protocols available:
 * SERIAL_5N1   5-bit No parity 1 stop bit
 * SERIAL_6N1   6-bit No parity 1 stop bit
 * SERIAL_7N1   7-bit No parity 1 stop bit
 * SERIAL_8N1 (the default) 8-bit No parity 1 stop bit
 * SERIAL_5N2   5-bit No parity 2 stop bits 
 * SERIAL_6N2   6-bit No parity 2 stop bits
 * SERIAL_7N2   7-bit No parity 2 stop bits
 * SERIAL_8N2   8-bit No parity 2 stop bits 
 * SERIAL_5E1   5-bit Even parity 1 stop bit
 * SERIAL_6E1   6-bit Even parity 1 stop bit
 * SERIAL_7E1   7-bit Even parity 1 stop bit 
 * SERIAL_8E1   8-bit Even parity 1 stop bit 
 * SERIAL_5E2   5-bit Even parity 2 stop bit 
 * SERIAL_6E2   6-bit Even parity 2 stop bit 
 * SERIAL_7E2   7-bit Even parity 2 stop bit  
 * SERIAL_8E2   8-bit Even parity 2 stop bit  
 * SERIAL_5O1   5-bit Odd  parity 1 stop bit  
 * SERIAL_6O1   6-bit Odd  parity 1 stop bit   
 * SERIAL_7O1   7-bit Odd  parity 1 stop bit  
 * SERIAL_8O1   8-bit Odd  parity 1 stop bit   
 * SERIAL_5O2   5-bit Odd  parity 2 stop bit   
 * SERIAL_6O2   6-bit Odd  parity 2 stop bit    
 * SERIAL_7O2   7-bit Odd  parity 2 stop bit    
 * SERIAL_8O2   8-bit Odd  parity 2 stop bit    
*/

mfalkvidd

Welcome to the mysensors community @toine33

What does the debug output from the node say?

Are you sure the nrf24 is correctly wired? Is your gateway and controller up and running?

If you haven't already, see https://forum.mysensors.org/topic/666/debug-faq-and-how-ask-for-help/ for the most common problems and how to troubleshoot them efficiently.

Toine33

So the output wich is given on the first sketch is :

/ISk5\2MT382-1003

0-0:96.1.1(5A424556303035303738373110323132)
1-0:1.8.1(08316.297*kWh)
1-0:1.8.2(08472.574*kWh)
1-0:2.8.1(00000.020*kWh)
1-0:2.8.2(00000.010*kWh)
0-0:96.14.0(0001)
1-0:1.7.0(0000.38*kW)
1-0:2.7.0(0000.00*kW)
0-0:17.0.0(0999.00*kW)
0-0:96.3.10(1)
0-0:96.13.1()
0-0:96.13.0()
0-1:24.1.0(3)
0-1:96.1.0(3238303131303031323031113336343132)
0-1:24.3.0(190907210000)(00)(60)(1)(0-1:24.2.1)(m3)
(04212.860)
0-1:24.4.0(1)
!

You can see here the output of my energy meter wich is given every 10 seconds

And this is the output when i am using the sketch with Mysensors,
It is curently not connected because im am unable at the moment.
The strange part is that the serial prints are not workig at this stage anymore or is this normal when using mysensors?

 
 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.0

16 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.0
25 TSM:INIT
26 TSF:WUR:MS=0
33 !TSM:INIT:TSP FAIL
35 TSM:FAIL:CNT=1
37 TSM:FAIL:DIS
38 TSF:TDI:TSL
10040 TSM:FAIL:RE-INIT
10042 TSM:INIT
10048 !TSM:INIT:TSP FAIL
10051 TSM:FAIL:CNT=2
10053 TSM:FAIL:DIS
10054 TSF:TDI:TSL
20057 TSM:FAIL:RE-INIT
20059 TSM:INIT
20065 !TSM:INIT:TSP FAIL
20068 TSM:FAIL:CNT=3
20070 TSM:FAIL:DIS
20071 TSF:TDI:TSL
30074 TSM:FAIL:RE-INIT
30076 TSM:INIT
30083 !TSM:INIT:TSP FAIL
30086 TSM:FAIL:CNT=4
30088 TSM:FAIL:DIS
30089 TSF:TDI:TSL
40092 TSM:FAIL:RE-INIT
40094 TSM:INIT
40100 !TSM:INIT:TSP FAIL
40103 TSM:FAIL:CNT=5
40105 TSM:FAIL:DIS
40107 TSF:TDI:TSL
50110 TSM:FAIL:RE-INIT
50112 TSM:INIT
50118 !TSM:INIT:TSP FAIL
50121 TSM:FAIL:CNT=6
50123 TSM:FAIL:DIS
50124 TSF:TDI:TSL
60127 TSM:FAIL:RE-INIT
60129 TSM:INIT
60135 !TSM:INIT:TSP FAIL
60138 TSM:FAIL:CNT=7
60140 TSM:FAIL:DIS
60141 TSF:TDI:TSL
120144 TSM:FAIL:RE-INIT
120146 TSM:INIT
120154 !TSM:INIT:TSP FAIL
120156 TSM:FAIL:CNT=7
120158 TSM:FAIL:DIS
120160 TSF:TDI:TSL

P.S
I have done some testing also on RS485 and had the same situation.

mfalkvidd

@toine33 yes this is normal. MySensors is unable to initialize the radio so it never reaches setup, nor loop.

electrik

You expect the baudrate to be 19200, but Mysensors also initialises the port at a baudrate. Maybe that one is done later and you should use the terminal on that baudrate?

Toine33

Hey guys,
Thanks for helping . The sketch was working after i have deleted the Serial.begin in the void setup.

void setup() {
Serial.begin(19200);

i only have some other issues at the moment haha,
The value's from the gas meter / high an low elecktricity are showing wrong within Domoticz
0_1567966720801_497ea466-8ee8-4bd4-be51-f4dc3f5c7099-image.png

When i am doing /1000 on the send values of the GAS meter and elecktricity meters i am getting an beter value but i loose 3 decimals and cant see any calculated value by domoticz.
Is there an option to send these decimals ?

0_1567967331476_a16e0f3a-43fe-4ce7-9de6-46a76a1d0547-image.png

#define MY_DEBUG 
#define MY_RS485
#define MY_RS485_DE_PIN 2
#define MY_RS485_BAUD_RATE 19200
#define MY_RS485_HWSERIAL Serial
#define MY_NODE_ID 3

#include <AltSoftSerial.h>
#include <SPI.h>
#include <MySensors.h>  

AltSoftSerial altSerial;

int msg[1];
const uint64_t pipe = 0xE8E8F0F0E1LL;

const int requestPin =  4;         
char input; // incoming serial data (byte)
bool readnextLine = false;
#define BUFSIZE 500
#define CHILD_ID_WATT 0
#define CHILD_ID_KWH_LOW 1
#define CHILD_ID_KWH_HIGH 2
#define CHILD_ID_GAS 3
#define CHILD_ID_CURRENT 4

char buffer[BUFSIZE]; //Buffer for serial data to find \n .
int bufpos = 0;
long mEVLT = 0; //Meter reading Electrics - consumption low tariff
long mEVHT = 0; //Meter reading Electrics - consumption high tariff
long mEAV = 0;  //Meter reading Electrics - Actual consumption
long mEAT = 0;  //Meter reading Electrics - Actual generated electricity (Solar panels)
long mG = 0;   //Meter reading Gas

MyMessage msgWatt(CHILD_ID_WATT, V_WATT);
MyMessage msgKwhLow(CHILD_ID_KWH_LOW, V_KWH);      //Was V_KWH
MyMessage msgKwhHigh(CHILD_ID_KWH_HIGH, V_KWH);     //Was V_KWH
MyMessage msgGas(CHILD_ID_GAS, V_VOLUME);



void setup() {
//  Serial.begin(19200);
//  delay(1000);
  
  altSerial.begin(9600);
  delay(1000);
}


void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Node", "1.0");
  present(CHILD_ID_WATT, S_POWER);
  present(CHILD_ID_KWH_LOW, S_POWER);
  present(CHILD_ID_KWH_HIGH, S_POWER);
  present(CHILD_ID_GAS, S_GAS);
}



void loop() {
  long tl = 0;
  long tld =0;
  if (altSerial.available()) {
      char input = altSerial.read();
      buffer[bufpos] = input&127;
      bufpos++;
      if (input == '\n') { // We received a new line (data up to \n)
        // 1-0:1.8.2 = Electricity consumption high tariff (DSMR v4.0)
        if (sscanf(buffer,"1-0:1.8.2(%ld%.%ld%*s" , &tl, &tld) >0 ) {
          tl *= 1000;
          tl += tld;
          mEVHT = tl;
          //mEVHT = tl * 1000 + tld;
          if (mEVHT > 0) {
  
            //mEVHT = 0;
          }
        }
  
  

        if (sscanf(buffer,"1-0:1.8.1(%ld.%ld" ,&tl, &tld)==2){
          tl *= 1000;
          tl += tld;
          mEVLT = tl;
  
          if (mEVLT > 0) {
  
  
          }
        }


  
        // 1-0:1.7.0 = Electricity consumption actual usage (DSMR v4.0)
        if (sscanf(buffer,"1-0:1.7.0(%ld.%ld" ,&tl , &tld) == 2)
        { 
          mEAV = (tl*1000)+tld*10;            
          if (mEAV > 0) {
  
          }
        }







/* Geeft actuele waarde door maar doet geen compare
if (sscanf(buffer,"(%ld.%ld" , &tl, &tld)==2 ) 
      {   mG = (tl*1000.0)+tld;
      mG = mG/1000;
      }
*/



//Gastand uitlezen
if (sscanf(buffer,"(%ld.%ld" , &tl, &tld)==2 ) 
      {   mG = (tl*1000.0)+tld;
      mG = mG;
      }




  
        // Empty buffer again (whole array)
        for (int i=0; i<500; i++)
        { 
          buffer[i] = 0;
        }
        bufpos = 0;
  
      }
       
      if (input == '!') {   //uitroepteken geeft einde van telegram aan, dus we gaan data versturen
        #ifdef DEBUG
          printData();
        #endif
        send(msgWatt.set(mEAV));
        send(msgKwhLow.set(mEVLT));
        send(msgKwhHigh.set(mEVHT));
        send(msgGas.set(mG));
        mEVHT=0;
        mEVLT = 0;
        mEAV = 0;
        mG = 0;
        //client.stop();
      } //Einde vraagteken detectie   
  
    } 

}

Thanks !

mfalkvidd

Nice work @toine33
Use set(value, numberOfDecimals)

Example:

send(msgWatt.set(mEAV, 3));

Documentation: https://www.mysensors.org/apidocs/MyMessage_8h.html#a8af6ca9ee9a61b5954e405a2ae7de361

Toine33

@mfalkvidd
Sorry for asking , but as you already noticed i am not super familiar to the arduino coding haha.

So i have tried send(msgWatt.set(mEAV, 3));
But the only output i am receiving is something like this,

TSF:MSG:SEND,3-3-0-0,s=3,c=1,t=35,pt=7,l=5,sg=0,ft=0,st=OK:4213752.000

What i would like to archieve is an value like
TSF:MSG:SEND,3-3-0-0,s=3,c=1,t=35,pt=7,l=5,sg=0,ft=0,st=OK:4213.752

I just would like to ad an decimal somehow and send this to Domoticz.

mfalkvidd

@toine33 asking is exactly what the forum is here for
This should work (note: .0 is a "trick" to let the compiler know we want a floating point / decimal number)

send(msgWatt.set(mEAV / 1000.0, 3));

Toine33

@mfalkvidd
Thank you so much Finnaly it is working as it should do!

#define MY_DEBUG 
#define MY_RS485
#define MY_RS485_DE_PIN 2
#define MY_RS485_BAUD_RATE 19200
#define MY_RS485_HWSERIAL Serial
#define MY_NODE_ID 3

#include <AltSoftSerial.h>
#include <SPI.h>
#include <MySensors.h>  

AltSoftSerial altSerial;

int msg[1];
const uint64_t pipe = 0xE8E8F0F0E1LL;

const int requestPin =  4;         
char input; // incoming serial data (byte)
bool readnextLine = false;
#define BUFSIZE 500
#define CHILD_ID_WATT 0
#define CHILD_ID_KWH_LOW 1
#define CHILD_ID_KWH_HIGH 2
#define CHILD_ID_GAS 3
#define CHILD_ID_CURRENT 4

char buffer[BUFSIZE]; //Buffer for serial data to find \n .
int bufpos = 0;
long mEVLT = 0; //Meter reading Electrics - consumption low tariff
long mEVHT = 0; //Meter reading Electrics - consumption high tariff
long mEAV = 0;  //Meter reading Electrics - Actual consumption
long mEAT = 0;  //Meter reading Electrics - Actual generated electricity (Solar panels)
long mG = 0;   //Meter reading Gas


MyMessage msgWatt(CHILD_ID_WATT, V_WATT);
MyMessage msgKwhLow(CHILD_ID_KWH_LOW, V_KWH);      //Was V_KWH
MyMessage msgKwhHigh(CHILD_ID_KWH_HIGH, V_KWH);     //Was V_KWH
MyMessage msgGas(CHILD_ID_GAS, V_VOLUME);



void setup() {
//  Serial.begin(19200);
//  delay(1000);
  
  altSerial.begin(9600);
  delay(1000);
}


void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Node", "1.0");
  present(CHILD_ID_WATT, S_POWER);
  present(CHILD_ID_KWH_LOW, S_POWER);
  present(CHILD_ID_KWH_HIGH, S_POWER);
  present(CHILD_ID_GAS, S_GAS);
}



void loop() {
  long tl = 0;
  long tld =0;
  if (altSerial.available()) {
      char input = altSerial.read();
      buffer[bufpos] = input&127;
      bufpos++;
      if (input == '\n') { // We received a new line (data up to \n)
        // 1-0:1.8.2 = Electricity consumption high tariff (DSMR v4.0)

        
        if (sscanf(buffer,"1-0:1.8.2(%ld.%ld" , &tl, &tld) >0 ) {
          tl *= 1000;
          tl += tld;
          mEVHT = tl;
          //mEVHT = tl * 1000 + tld;
          if (mEVHT > 0) {
  
            //mEVHT = 0;
          }
        }
  
  

        if (sscanf(buffer,"1-0:1.8.1(%ld.%ld" ,&tl, &tld)==2){
          tl *= 1000;
          tl += tld;
          mEVLT = tl;
  
          if (mEVLT > 0) {
  
  
          }
        }


  
        // 1-0:1.7.0 = Electricity consumption actual usage (DSMR v4.0)
        if (sscanf(buffer,"1-0:1.7.0(%ld.%ld" ,&tl , &tld) == 2)
        { 
          mEAV = (tl*1000)+tld*10;            
          if (mEAV > 0) {
  
          }
        }




//Gastand uitlezen

if (sscanf(buffer,"(%ld.%ld" , &tl, &tld)==2 ) 
      {   mG = (tl*1000.0)+tld;
      mG = mG;
      }




  
        // Empty buffer again (whole array)
        for (int i=0; i<500; i++)
        { 
          buffer[i] = 0;
        }
        bufpos = 0;
  
      }
       
      if (input == '!') {   //uitroepteken geeft einde van telegram aan, dus we gaan data versturen
        #ifdef DEBUG
          printData();
        #endif
        send(msgWatt.set(mEAV));
        send(msgKwhLow.set(mEVLT / 1000.0, 3)); 
        send(msgKwhHigh.set(mEVHT / 1000.0, 3));
        send(msgGas.set(mG / 1000.0, 3));
        mEVHT=0;
        mEVLT = 0;
        mEAV = 0;
        mG = 0;
        //client.stop();
      } //Einde vraagteken detectie   
  
    } 

}

And here an picture how it is showing up in domoticz:

0_1568053520513_cc789582-9497-47ae-a278-d906a1b3a0fd-image.png

P1 not working when using Mysensors ?

Suggested Topics

Day 1 - Status report
Announcements • • hek

Forum Search not working?
Troubleshooting • • Gibber

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA)
Troubleshooting • • se-O-matic

Extraneous info in Debug log
Troubleshooting • debug log • • Gibber

Raspberry Pi 5: invalid GPIO 9
Troubleshooting • • igo

95
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

P1 not working when using Mysensors ?

Suggested Topics

Day 1 - Status report Announcements • • hek

Forum Search not working? Troubleshooting • • Gibber

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA) Troubleshooting • • se-O-matic

Extraneous info in Debug log Troubleshooting • debug log • • Gibber

Raspberry Pi 5: invalid GPIO 9 Troubleshooting • • igo

95Online

11.5kUsers

11.1kTopics

112.7kPosts

Day 1 - Status report
Announcements • • hek

Forum Search not working?
Troubleshooting • • Gibber

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA)
Troubleshooting • • se-O-matic

Extraneous info in Debug log
Troubleshooting • debug log • • Gibber

Raspberry Pi 5: invalid GPIO 9
Troubleshooting • • igo

95
Online

11.5k
Users

11.1k
Topics

112.7k
Posts