Wemos d1 mini : gateway error .
-
Oh, I will check the wiring ...
I taught It means that it can't connect to wifi ...So it's normal that I can't ping the wemos ...
For the sketch I just upload the example sketch for esp8266gateway..
/* * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2019 Sensnology AB * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * REVISION HISTORY * Version 1.0 - Henrik Ekblad * Contribution by a-lurker and Anticimex, * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de> * Contribution by Ivo Pullens (ESP8266 support) * * DESCRIPTION * The EthernetGateway sends data received from sensors to the WiFi link. * The gateway also accepts input on ethernet interface, which is then sent out to the radio network. * * VERA CONFIGURATION: * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin. * E.g. If you want to use the default values in this sketch enter: 192.168.178.66:5003 * * LED purposes: * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch, only the LEDs that is defined is used. * - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - ERR (red) - fast blink on error during transmission error or receive crc error * * See https://www.mysensors.org/build/connect_radio for wiring instructions. * * If you are using a "barebone" ESP8266, see * https://www.mysensors.org/build/esp8266_gateway#wiring-for-barebone-esp8266 * * Inclusion mode button: * - Connect GPIO5 (=D1) via switch to GND ('inclusion switch') * * Hardware SHA204 signing is currently not supported! * * Make sure to fill in your ssid and WiFi password below for ssid & pass. */ // Enable debug prints to serial monitor #define MY_DEBUG // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h #define MY_BAUD_RATE 9600 // Enables and select radio type (if attached) #define MY_RADIO_RF24 //#define MY_RADIO_RFM69 //#define MY_RADIO_RFM95 #define MY_GATEWAY_ESP8266 #define MY_WIFI_SSID "xxxx" #define MY_WIFI_PASSWORD "xxxxxx" // Enable UDP communication //#define MY_USE_UDP // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below // Set the hostname for the WiFi Client. This is the hostname // it will pass to the DHCP server if not static. #define MY_HOSTNAME "ESP8266_GW" // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP) #define MY_IP_ADDRESS 192,168,1,112 // If using static ip you can define Gateway and Subnet address as well #define MY_IP_GATEWAY_ADDRESS 192,168,1,1 #define MY_IP_SUBNET_ADDRESS 255,255,255,0 // The port to keep open on node server mode #define MY_PORT 5003 // How many clients should be able to connect to this gateway (default 1) #define MY_GATEWAY_MAX_CLIENTS 2 // Controller ip address. Enables client mode (default is "server" mode). // Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 //#define MY_CONTROLLER_URL_ADDRESS "my.controller.org" // Enable inclusion mode //#define MY_INCLUSION_MODE_FEATURE // Enable Inclusion mode button on gateway //#define MY_INCLUSION_BUTTON_FEATURE // Set inclusion mode duration (in seconds) //#define MY_INCLUSION_MODE_DURATION 60 // Digital pin used for inclusion mode button //#define MY_INCLUSION_MODE_BUTTON_PIN D1 // Set blinking period //#define MY_DEFAULT_LED_BLINK_PERIOD 300 // Flash leds on rx/tx/err // Led pins used if blinking feature is enabled above //#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin //#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin //#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED #include <MySensors.h> void setup() { // Setup locally attached sensors } void presentation() { // Present locally attached sensors here } void loop() { // Send locally attached sensors data here } -
Now the wiring check.
I have a nrf24l01 with antenna, and nothing is written on the board ...
Does someone have a wiring diagram for that nrf module ?Thank you.
-
Now the wiring check.
I have a nrf24l01 with antenna, and nothing is written on the board ...
Does someone have a wiring diagram for that nrf module ?Thank you.
@David-Marlinge could you expand on what you mean by "nothing is written on the board". Which board?
The wiring is available at https://www.mysensors.org/build/connect_radio#nrf24l01+-&-esp8266
-
nothing is written on the nrf24L01 board ...
I send a picture ...
-
nothing is written on the nrf24L01 board ...
I send a picture ...
-
If it's the same wiring, I connect like your link, but it does not work.
Now I can ping the wifi adress even if the nrf24l01 is not plugin ... In fact It doesn't take the adress I give in the sketch ....
-
What I want to say, is that nothing is written on the pin ... So How can I be sure where the gnd, vcc and so on are ???
-
What I want to say, is that nothing is written on the pin ... So How can I be sure where the gnd, vcc and so on are ???
-
I have already check, nothing is written on the store where i bought them ...
Is tha capacitor needed ? and Must the whole thing works connected on a PC usb ?
-
So I check the wiring. I think a wire was not well plugged.
Now it works.
I have such "sentences" :
11:52:22.169 -> 12496 GWT:TIN:CONNECTING...
11:52:22.499 -> scandone
11:52:23.204 -> 13525 GWT:TIN:CONNECTING...
11:52:23.204 -> 13555 GWT:TIN:IP: 192.168.1.111
11:52:23.251 -> 13588 MCO:BGN:STP
11:52:23.251 -> 13607 MCO:BGN:INIT OK,TSP=1
11:52:23.298 -> 13637 TSM:READY:NWD REQ
11:52:23.346 -> 13665 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
11:52:23.535 -> pm open,type:2 0
