!TSM:ID:FAIL need help

[robos]

Hi

it's my first post and i need help.
I want to use mysensors as move sensor and my problem is sender probably doesn't want exit from init mode ??

10093 !TSM:ID:FAIL	Did not receive a node id from controller. Is your controller connected and correctly configured?
10094 TSM:FAIL:CNT=1	Transition to Failure state, consecutive failure counter is 1
10096 TSM:FAIL:DIS	Disable transport
10098 TSF:TDI:TSL	Set transport to sleep

program never goes to void loop
I need a hint to sketch to work.
Power is ok ; messages go thru gateway to mqtt

Test sketch:

#define MY_DEBUG
#define MY_RADIO_RF24
#include <MySensors.h>

uint32_t SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define CHILD_ID 1   // Id of the sensor child
#define MY_NODE_ID 1

MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()
{
	pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
}

void presentation()
{
	sendSketchInfo("Motion Sensor", "1.0");// Send the sketch version information to the gateway and Controller
	present(CHILD_ID, S_MOTION);// Register all sensors to gw (they will be created as child devices)
}

void loop()
{
  Serial.println(" - =  T E S T    L O O P  = -");
  

	bool tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH;  // Read digital motion value
	send(msg.set(tripped?"1":"0"));  // Send tripped value to gw

	// Sleep until interrupt comes in on motion sensor. Send update every two minute.
	sleep(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), CHANGE, SLEEP_TIME);
}

Log from sender

__  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
       |___/                      2.3.2

16 MCO:BGN:INIT NODE,CP=RNNNA---,FQ=16,REL=255,VER=2.3.2
26 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSM:FPAR
38 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
944 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
949 TSF:MSG:FPAR OK,ID=0,D=1
2048 TSM:FPAR:OK
2049 TSM:ID
2050 TSM:ID:REQ
2053 TSF:MSG:SEND,255-255-0-0,s=2,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4060 TSM:ID
4061 TSM:ID:REQ
4063 TSF:MSG:SEND,255-255-0-0,s=221,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
6071 TSM:ID
6072 TSM:ID:REQ
6074 TSF:MSG:SEND,255-255-0-0,s=184,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
8082 TSM:ID
8083 TSM:ID:REQ
8085 TSF:MSG:SEND,255-255-0-0,s=147,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
10093 !TSM:ID:FAIL
10094 TSM:FAIL:CNT=1
10096 TSM:FAIL:DIS
10098 TSF:TDI:TSL

Log from gateway:

39 MCO:BGN:INIT GW,CP=RNNGF---,FQ=240,REL=255,VER=2.3.2
44 TSF:LRT:OK
47 TSM:INIT
51 TSF:WUR:MS=0
60 TSM:INIT:TSP OK
61 TSM:INIT:GW MODE
66 TSM:READY:ID=0,PAR=0,DIS=0
70 MCO:REG:NOT NEEDED
186 GWT:TPC:CONNECTING...
1189 MCO:BGN:STP
1191 MCO:BGN:INIT OK,TSP=1
1195 GWT:TPC:IP=192.168.1.88
1200 GWT:RMQ:CONNECTING...
1222 GWT:RMQ:OK
1224 GWT:TPS:TOPIC=/mysens-out/0/255/0/0/18,MSG SENT
1232 TSM:READY:NWD REQ
1237 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
31573 TSF:MSG:READ,255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
31578 TSF:MSG:BC
31582 TSF:MSG:FPAR REQ,ID=255
31587 TSF:PNG:SEND,TO=0
31591 TSF:CKU:OK
31595 TSF:MSG:GWL OK
32480 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
33587 TSF:MSG:READ,255-255-0,s=2,c=3,t=3,pt=0,l=0,sg=0:
33592 GWT:TPS:TOPIC=/mysens-out/255/2/3/0/3,MSG SENT
35598 TSF:MSG:READ,255-255-0,s=221,c=3,t=3,pt=0,l=0,sg=0:
35603 GWT:TPS:TOPIC=/mysens-out/255/221/3/0/3,MSG SENT
37609 TSF:MSG:READ,255-255-0,s=184,c=3,t=3,pt=0,l=0,sg=0:
37614 GWT:TPS:TOPIC=/mysens-out/255/184/3/0/3,MSG SENT
39620 TSF:MSG:READ,255-255-0,s=147,c=3,t=3,pt=0,l=0,sg=0:
39625 GWT:TPS:TOPIC=/mysens-out/255/147/3/0/3,MSG SENT

My Gateway is ESP32/NRF24 +MQTT and message to mqtt is ok (this is defferent log)

27.12.2020, 17:21:33node: edf01ef4.eb25f /mysens-out/255/2/3/0/3 : msg.payload : string[0]""
27.12.2020, 17:21:35node: edf01ef4.eb25f  /mysens-out/255/221/3/0/3 : msg.payload : string[0]""
27.12.2020, 17:21:37node: edf01ef4.eb25f  /mysens-out/255/184/3/0/3 : msg.payload : string[0]""
27.12.2020, 17:21:39node: edf01ef4.eb25f  /mysens-out/255/147/3/0/3 : msg.payload : string[0]""

[BearWithBeard]

Welcome @robos!

The gateway is sending an ID request via MQTT to the controller, but doesn't get a reply.

From the Building a MQTT Gateway guide:

NOTE: No controller supports dynamic ID assignment through MQTT. All nodes must have MY_NODE_ID defined in the sketch to work with MQTT. If you don't set MY_NODE_ID, nodes will complain with the message "!TSM:ID:FAIL".

If you want to keep using MQTT, you have to add #define MY_NODE_ID n before(!) #include <MySensors.h>, whereby n may be any (unused) number between 1 and 254.

For automatic ID assignment through the controller, select a different gateway, like serial or ethernet.

[robos]

Thanks

#define MY_NODE_ID n before(!) #include <MySensors.h> that helped a lot !!!