Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Mother/daughter board system

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/27/Motherdaughter-board-system
Reply Quote 0
1 Reply Last reply
TD22057 Hardware Contributor last edited by

@hek - I tried using the github extraction system and I'm not sure it's working. I didn't fill any files/images/etc manually, I just gave it the repository. Is the system supposed to extract everything automatically or is there something else I need to do?
Reply Quote 0
1 Reply Last reply
TD22057 Hardware Contributor last edited by

I've added all the files manually so things should be there now (though I'd recommend grabbing things from github to preserve directory structure and get all the files).
Reply Quote 0
1 Reply Last reply

3
Posts

1410
Views

Suggested Topics

💬 Easy Switch Box
OpenHardware.io • mysensors arduino switch atmega328 lora low power • • openhardware.io

1

0
Votes

1
Posts

18
Views

No one has replied
MySensor Network on RS485 - only single node visible
Troubleshooting • mysensors • • Rysiek

13

0
Votes

13
Posts

146
Views

Very useful topic for me, thanks. Even though it's been a long time, the information was useful to me. And especially the information on the link you sent.
💬 NModule Temperature, Humidity, Light, Door sensor shield
OpenHardware.io • mysensors temperature contest2017 light i2c nmodule door • • openhardware.io

41

0
Votes

41
Posts

10457
Views

Hello, I'm thinking about upgrading this board to include pinout for LIS3DH breakout board, like this one : https://www.aliexpress.com/item/LIS3DH-Three-Converters-Motion-Accelerometer-Triaxial-Acceleration-Temperature-Sensor-Module-Development-Board-Replace-ADXL345/32840326778.html and ditch the ADXL shield as it's not a good solution, it has either the ADXL345 which uses too much power, or the ADXL362 which is ultra low power but lacks advanced functionality like tap/double tap detection. I would like to have feedback of users on this (do it sound useful ?), and also know if anyone uses the SMD footprints on the board, for leds and for reserve capacitors, as it could be a cleaner board without those footprints. I would make the following changes : put footprint for LIS3DH accelerometer along the "NModule connector" as it has too many pins to put elsewhere keep only one I2C footprint on the side, for "GY-49" MAX44009 light sensor breakout board: https://www.aliexpress.com/item/GY-49-MAX44009-Ambient-Light-Sensor-Module-for-Arduino-with-4P-Pin-Header-Module/32828654450.html temperature/humidity would be via the existing "SMD" footprint, it's not through hole but very easy to solder as it's 2.54mm pad spacing remove SMD footprints for LED, add footprint for through hole reserve capacitor, keep SMD footprints for reserve capacitors only if I have space for them shield would be a bit extended to go over the 2 M2 holes in the "power" part of the NModule, so it could be fitted with spacers and nylon screws and have stable/reliable mechanical connection between NModule and Shield. Basically this would be the footprint of the shield : So in the end it would make one shield to have Temperature/Humidity/Light/Acceleration or Temperature/Humidity/Light/Door.
💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

14

1
Votes

14
Posts

4077
Views

@Samuel235 said in Homini AC Powered Relay (2) Module: OMRON G3MB-202P Okay I'm trying to help you with the fuse component. I found a datasheet for the OMRON G3MB-202P. And there are enoght information to be known for fuse selection. I try to calculate it here (and i will try it with my bad English ). The most important information is the melting integral. The Melting integral has A²s as unit. So this means the maximum current for a time can exists without damaging the device. For further information look at wikipedia. So we need any further information about: the protection which is present before (the typical circuit protection in private houses) the melting integral from the device which we want to protect the maximum voltage the maximum switching current the breaking capacity Inrush current for the switched devices (we can't know) Typical values for an automatic circuit breaker in private houses are: from 25 to 100 A²s 230 V AC 16 A So this protection isn't good enough for our relay. The relay have these values: 230 V AC 2 A maximum switching current I²t value (melting integral): 4 A²s the allowed inrush current over a small time is higher than the melting integral. It is a bit confusing i think, but if we calculate the protection for the given melting integral and it's fine. So we can define the parameters for the client (switching site of this application here) The fuse have to be: I²s value higher or equal than the I²s value from the existing protection rating voltage over 230 V AC rating current 2 A or lower (because 2 A is the maximum at 25 °C, for 40 °C it is about 1.6 A) a maximum switching time of 1 second at 2 A or lower time with higher current but below 4A²s! To calculate use the switching time from the fuse datasheet an multiply it two times with the given current for this switching time. And i think a fast blow fuse would be the best. There are SMD fuses with 10.1 x 3 mm and 250 V AC available. If there is no fuse available with the values above, we could combine multiple fuses. A possible solution could be one bigger fuse for both relays and the ac/dc component. And a smaller fuse for the switching site of the relay and the HLK-PM01. But for this it is important that the circuit have only one input for the hot one (L) of 230 V and one output for each relay. In this case we could reduce the big connectors from 6 to 4. Like (L, N, Relay1, Relay2). And the temperature fuse can work for all components too So the protection for the primary site of the HLK-PM01 is a problem i think. Because the are no information available about the I²s value from HLK-PM01. I hope you can understand my English and could follow my explanation?
Multisensor
OpenHardware.io • mysensors temperature mysensor motion dht22 rgb lux rfid buzzer • • openhardware.io

3

2
Votes

3
Posts

2408
Views

@yoonie said: For the pro mini version, should i create another Openhardware project, or should i put it here, in the already existing project? Might be better to create a new project as they uses a different set of design files.
Which presentation to use for a Turbidity Sensor?
My Project • mysensors • • Shiny

1

0
Votes

1
Posts

21
Views

No one has replied
💬 Gesture controlled MySensors, Floor lamp
OpenHardware.io • mysensors contest2016 floor lamp gesture controlled • • openhardware.io

39

0
Votes

39
Posts

6129
Views

@mfalkvidd The mySensors site with all the build examples. The gesture control sensors is still in MySensors 1.x version
💬 RFM69 - 8 relays board
OpenHardware.io • rfm69 relay • • openhardware.io

1

0
Votes

1
Posts

894
Views

No one has replied

Mother/daughter board system

Suggested Topics

💬 Easy Switch Box
OpenHardware.io • mysensors arduino switch atmega328 lora low power • • openhardware.io

MySensor Network on RS485 - only single node visible
Troubleshooting • mysensors • • Rysiek

💬 NModule Temperature, Humidity, Light, Door sensor shield
OpenHardware.io • mysensors temperature contest2017 light i2c nmodule door • • openhardware.io

💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

Multisensor
OpenHardware.io • mysensors temperature mysensor motion dht22 rgb lux rfid buzzer • • openhardware.io

Which presentation to use for a Turbidity Sensor?
My Project • mysensors • • Shiny

💬 Gesture controlled MySensors, Floor lamp
OpenHardware.io • mysensors contest2016 floor lamp gesture controlled • • openhardware.io

💬 RFM69 - 8 relays board
OpenHardware.io • rfm69 relay • • openhardware.io

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

Mother/daughter board system

Suggested Topics

💬 Easy Switch Box OpenHardware.io • mysensors arduino switch atmega328 lora low power • • openhardware.io

MySensor Network on RS485 - only single node visible Troubleshooting • mysensors • • Rysiek

💬 NModule Temperature, Humidity, Light, Door sensor shield OpenHardware.io • mysensors temperature contest2017 light i2c nmodule door • • openhardware.io

💬 Homini AC Powered Relay (2) Module OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

Multisensor OpenHardware.io • mysensors temperature mysensor motion dht22 rgb lux rfid buzzer • • openhardware.io

Which presentation to use for a Turbidity Sensor? My Project • mysensors • • Shiny

💬 Gesture controlled MySensors, Floor lamp OpenHardware.io • mysensors contest2016 floor lamp gesture controlled • • openhardware.io

💬 RFM69 - 8 relays board OpenHardware.io • rfm69 relay • • openhardware.io

0Online

11.2kUsers

11.1kTopics

112.5kPosts

💬 Easy Switch Box
OpenHardware.io • mysensors arduino switch atmega328 lora low power • • openhardware.io

MySensor Network on RS485 - only single node visible
Troubleshooting • mysensors • • Rysiek

💬 NModule Temperature, Humidity, Light, Door sensor shield
OpenHardware.io • mysensors temperature contest2017 light i2c nmodule door • • openhardware.io

💬 Homini AC Powered Relay (2) Module
OpenHardware.io • mysensors relay contest2017 switch light lighting • • openhardware.io

Multisensor
OpenHardware.io • mysensors temperature mysensor motion dht22 rgb lux rfid buzzer • • openhardware.io

Which presentation to use for a Turbidity Sensor?
My Project • mysensors • • Shiny

💬 Gesture controlled MySensors, Floor lamp
OpenHardware.io • mysensors contest2016 floor lamp gesture controlled • • openhardware.io

💬 RFM69 - 8 relays board
OpenHardware.io • rfm69 relay • • openhardware.io

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts