Sensebender Micro

[Anticimex]

@alexsh1 You could also try soft signing on the sensebender and see if that makes a difference. Perhaps the atsha device interferes with the radio (this depends on routing and such things). I have no sensebender myself and I have not noticed the behavior you describe with nrf24 and atsha204a.

[alexsh1]

@Anticimex I tried the sensebender with soft singing - still the same st=fail

[Anticimex]

@alexsh1 Ok. I guess that is "good news for me" as it rules out signing related hardware as well. I guess so far, the only conclusion is that rf performance is to some extent degraded on the sensebender.

[Yveaux]

@alexsh1 just a hunch: do both nodes have identical CPU's & clock frequency?

[alexsh1]

@Yveaux Correct - I have used Pro Mini 3.3V 8Mhz which corresponds to the sensebender

[ximinez]

Is there a "pre setup" available yet? The failed transmits are before sensor values are transmitted, so they aren't in the actual sketch but somewhere in the library. I'd like to try just sleeping the sensor 5-10 seconds before the initial data is transmitted and see if that makes a difference.

[alexsh1]

@Anticimex Yeah it seems like a combination of things but not a signing problem

[Anticimex]

@ximinez not sure. I know it has been discussed. But you can always patch the library to test.

[alexsh1]

@ximinez I do not think so. Either to patch the library or you do it in the sketch. Unless I do not know some other secret place.

[hek]

@ximinez

You can add a before()-method.

[ximinez]

@hek said:

@ximinez

You can add a before()-method.

It's that easy? I'll give it a try when I get around to it, unless @alexsh1 feels like trying it first :)

[Haakon]

Hi! I have just gotten four Sensebenders and was hoping to connect PIRs to them and powering them with AA batteries. I understand from the forums that people do this. But is there a working Arduino sketch example implementing a PIR for wake-up out there? (And perhaps there is a more detailed description for such a hardware setup for us newbies?)

[tomkxy]

I have bought another couple of sensebenders.
I am not able to upload sketches to one of them.
When I connect the programmer the status led goes to solid red. From another one, I realized that it is not solid red.

What is the meaning of a solid red status LED?

[hek]

What does the log say when you upload?

[alexsh1]

@Haakon Have a look here - https://forum.mysensors.org/topic/2478/slim-cr123a-2aa-battery-node
Just change your board for sensebender.

[tomkxy]

@hek

D -Uflash:w:/var/folders/3s/rjbksrj96nv0hqfqjlpfw8bm0000gn/T/build8699526819198040594.tmp/SecurityPersonalizer.cpp.hex:i 

avrdude: Version 6.0.1, compiled on Apr 14 2015 at 16:30:25
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "/Applications/Arduino.app/Contents/Java/hardware/tools/avr/etc/avrdude.conf"
         User configuration file is "/Users/tom/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/cu.usbserial-DA01IGTO
         Using Programmer              : arduino
         Overriding Baud Rate          : 57600
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: ser_recv(): read error: Device not configured
Probleme beim Hochladen auf die Platine. Hilfestellung dazu unter http://www.arduino.cc/en/Guide/Troubleshooting#upload

I have Sensebender selected as board.

Btw, where is the hardware folder? It is not present anymore in the development branch?

[hek]

@tomkxy said:

Btw, where is the hardware folder? It is not present anymore in the development branch?

You can use the build in board manager nowadays.
https://github.com/mysensors/ArduinoBoards

Check board for solder bridges or anything suspicious.

[johnr]

Hi,

I wonder if anyone modified the original sensebender sketch to include a door sensor?
Do you need a pullup? If you have a sketch somewhere I would be happy if you could send/post it, as I have problem finding time to code right now.

[martinhjelmare]

@johnr

Here's one for a button, but shouldn't matter:

https://forum.mysensors.org/topic/2887/sensebender-micro-button/2

[alexsh1]

@johnr This is easy.

// PIN = 2 or 3 only
 
void setup {
  pinMode(PIN,INPUT);
  digitalWrite(PIN,HIGH);
}

This activates internal pull-up.
The sensebender has got pinout of Pro Mini