Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

DomoticZ on RPi successfully running

luisgcu last edited by luisgcu

I gave up trying to set the openhab.. mosquitto and all that on my Rpi, honestly I am very new on the rpi and linux.. that is fact ..but other side there is not easy guide to follow in order to install successfully the openhab + mosquitto +my sensors. I have spent a sum of 12 hours without getting to much valuable. Instead I have decided to go to Domotic Z I have followed that guide https://www.domoticz.com/wiki/Domoticz_RaspberryPi_SD_Image , it took me 1 hour to set up everything and now I have fully working my ESP8266 gateway sending my sensors data to domoticZ on my RPI, just follow that link and you'll get domotic z installed on your rpi.
Reply Quote 1
1 Reply Last reply

1
Posts

2015
Views

Suggested Topics

Vera Gateway Versions
Troubleshooting • • karenbobiv

5

0
Votes

5
Posts

2061
Views

@karenbobiv I doubt it's related to the MySensors communication. Are you using a Dallas temp sensor? Could you check that the is actually connected to the dallas sensor by using isConnected(). When googling your problem I found a few hits on -196.6 which is the error code (DEVICE_DISCONNECTED) converted to Fahrenheit. Start debug mode (Config.h) to see what the sensor actually sends.
domoticz tables and mysensors
Domoticz • • ebioz

1

0
Votes

1
Posts

17
Views

No one has replied
eventsystem: problem writing file
Domoticz • • Feliw05

2

0
Votes

2
Posts

11
Views

Save the script directly from Windows and test if it can be opened in Domoticz.
Node update on value from Domoticz
Domoticz • • zboblamont

2

0
Votes

2
Posts

16
Views

@zboblamont OK, so experiments concluded that the return data from the latest version of Domoticz is a String whether it be V_VARx or V_TEXT. I tried the dual declaration using the same CHILD_ID as intended and as VAR_X (using an RF24 - not sure of the relevance) and the actual value sent but failed to make any sense of abstracting the Ulong conversion or the string. Only by presenting a fresh CHILD_ID and duplicating the send of data (water meter) as a V_VAR1 could I recover the last sent reading as a V_VAR1 from that fresh CHILD_ID, thence eventually arriving at 'strtoul' as a solution to restoring the last known value. For clarity my Gateway and Controller run on a UPS, and I hope shortly to add the spare router to that UPS so I'm not left in the dark on what is happening in the dark on a battery powered laptop... Hope this helps others trying to keep track of meters between relentless power cuts and reboots...
How to get the bad status (red) for Temperature Node
Domoticz • • giangired

5

0
Votes

5
Posts

55
Views

Thanks everyone for the answers. However what I would like to do is create a routine with Dzvents that when I have the "red" indication (as shown in the image) causes a switch to operate which cuts the voltage to a device. The value of ".lastUpdate.minutesAgo" seems not to be the right solution because it continues to be increased in any case, regardless of the temperature value and the status of the "red" or normal indication.
help please
Domoticz • • clivec

4

0
Votes

4
Posts

69
Views

@mutantx, sorry for the late reply, but I was on holidays I've no experience with this sketch code, nor the hardware build of this mp3 player. Try to contact the author of this player or you can check the general documentation about the use of V_VARx / S_CUSTOM : https://www.mysensors.org/download/serial_api_20 Try to break up things in little pieces when accumulating knowledge about mysensors. Big complicated sketches can be overwhelming. I start always, when troubleshouting, with the cleanest version of the script, with minimum code required for operation. And then I build it up.

DomoticZ on RPi successfully running

Suggested Topics

Vera Gateway Versions
Troubleshooting • • karenbobiv

domoticz tables and mysensors
Domoticz • • ebioz

eventsystem: problem writing file
Domoticz • • Feliw05

Node update on value from Domoticz
Domoticz • • zboblamont

How to get the bad status (red) for Temperature Node
Domoticz • • giangired

help please
Domoticz • • clivec

10
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

DomoticZ on RPi successfully running

Suggested Topics

Vera Gateway Versions Troubleshooting • • karenbobiv

domoticz tables and mysensors Domoticz • • ebioz

eventsystem: problem writing file Domoticz • • Feliw05

Node update on value from Domoticz Domoticz • • zboblamont

How to get the bad status (red) for Temperature Node Domoticz • • giangired

help please Domoticz • • clivec

10Online

11.4kUsers

11.1kTopics

112.7kPosts

Vera Gateway Versions
Troubleshooting • • karenbobiv

domoticz tables and mysensors
Domoticz • • ebioz

eventsystem: problem writing file
Domoticz • • Feliw05

Node update on value from Domoticz
Domoticz • • zboblamont

How to get the bad status (red) for Temperature Node
Domoticz • • giangired

help please
Domoticz • • clivec

10
Online

11.4k
Users

11.1k
Topics

112.7k
Posts