ESP8266 gateway and sensor node not talking - noobie

pwatt01

Hello all,

I just had all of my parts arrive and are builing my contoller and first sensor (DHT11 on MEGA clone). After flashing both (using the development build), they both seem to be working according to the serial monitor, but i cannot seem to make them talk to each other!

Can anyone help me out? I am using the examples on both the gateway and node.

Here is the output from the gateway after pressing reset:

0‚~?–4“Ò¶£ÿOAaû0;0;3;0;9;Starting...
scandone
f 0, ....scandone
.add 0
aid 4
pm open phy_2,type:2 0 0
cnt 

connected with <ssid>, channel 1
ip:192.168.1.200,mask:255.255.255.0,gw:192.168.1.254
.IP: 192.168.1.200
0;0;3;0;9;gateway started, id=0, parent=0, distance=0

this is from the sensor node:

Starting...
find parent
send: 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
find parent
send: 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
read: 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
find parent
send: 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
read: 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
read: 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
read: 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
find parent
send: 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
read: 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
find parent
send: 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
sensor started, id=255, parent=255, distance=255
T:21.00
find parent
send: 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
read: 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
H:36.00
find parent
send: 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:

and here is the log from domotitz

2015-10-29 07:11:37.529 Domoticz V2.3347 (c)2012-2015 GizMoCuz
2015-10-29 07:11:37.529 Build Hash: b835f24, Date: 2015-10-15 03:16:03
2015-10-29 07:11:37.554 Sunrise: 05:48:00 SunSet:19:10:00
2015-10-29 07:11:37.554 EventSystem: reset all events...
2015-10-29 07:11:37.561 Active notification subsystems: (0/10)
2015-10-29 07:11:37.657 Webserver started on port: 8080
2015-10-29 07:11:37.662 Started shared server on: ::
2015-10-29 07:11:37.720 Incoming connection from: 127.0.0.1
2015-10-29 07:11:39.666 EventSystem: reset all events...
2015-10-29 07:11:39.667 EventSystem: reset all device statuses...
2015-10-29 07:11:39.667 EventSystem: Started
2015-10-29 07:11:41.672 MySensors: connected to: 192.168.1.200:5003
2015-10-29 07:11:41.672 MySensors: Gateway Ready...
2015-10-29 07:11:42.366 Login successfull : user 'admin'

pwatt01

OK.. i think after looking a bit more they are talking.. however there are a few issues and they are not understanding each other or somehitng. I remember reading before that there is a way to flash the device back to stock/wipe the EEPROM. DOes anyone know the link to that?

hek

What does the gateway log say when you restart the sensor?

pwatt01

Nothing. Or no change at least. The shots above are still the only messages that I am getting, apart from the ESP8266 rebooting by itself occasionaly, and the sensor node tends to repeat itself as new readings come in

Mersing

Hello,

I've setup a ESP8266 Gateway with RF24 Radio.
I've got a RF24 Node with DS18B20.
I'ved used Esp8266Gateway.ino / DallasTemperatureSensor.ino out of the box.
Everything is working fine. Node and GW are communicating.

I'm now trying to run this setup with RF69. I'm facing the same issue as described in the initial post.

Pin mapping
RF69 <-> ESP8266
DIO0 <-> GPIO4
SCK <-> GPIO14
MOSI <-> GPIO13
MISO <-> GPIO12
CS <-> GPIO15

From RFM69.h
define RF69_SPI_CS               SS

#elif defined(ARDUINO_ARCH_ESP8266)
  // TODO !! Untested code! Entering unknown territory...
  #define RF69_IRQ_PIN          4
  #define RF69_IRQ_NUM          0
#endif

By default, from RFM69.h, RF69_IRQ_PIN is 2.
However to properly boot GPIO15 must be LOW and GPIO2 must be HIGH.
Connecting IRQ to GPIO2, RF69 pull its IRQ to LOW, making GPIO2 LOW and ESP8266 not booting.
Then I'll use GPIO4.

I'm using the same config file for GW and Node (e.g same NWETWORKID, ENCRYPTKEY, FREQUENCY).

On the Node Side : DallasTemperatureSensor.ino

#define isRFM69HW true // Enable High Power
MyTransportRFM69 transport( RFM69_FREQUENCY, RFM69_NETWORKID, RF69_SPI_CS, RF69_IRQ_PIN, isRFM69HW, RF69_IRQ_NUM );
MySensor gw( transport );
gw.begin( NULL, 8 );

On the GW Side : Esp8266Gateway.ino

#define isRFM69HW true
MyTransportRFM69 transport(RFM69_FREQUENCY, RFM69_NETWORKID, RF69_SPI_CS, RF69_IRQ_PIN, isRFM69HW, RF69_IRQ_NUM);

OUTPUT

GW Side

ESP8266 MySensors Gateway
Connecting to WRT54G
.......Connected!
IP: 192.168.1.25
0;0;3;0;9;gateway started, id=0, parent=0, distance=0

Node

send: 8-8-0-0 s=255,c=0,t=17,pt=0,l=3,sg=0,st=fail:1.5
send: 8-8-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=fail:0
sensor started, id=8, parent=0, distance=1
send: 8-8-0-0 s=255,c=3,t=11,pt=0,l=18,sg=0,st=fail:Temperature Sensor
send: 8-8-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=fail:1.1
send: 8-8-0-0 s=0,c=0,t=6,pt=0,l=0,sg=0,st=fail:
send: 8-8-0-0 s=0,c=1,t=0,pt=7,l=5,sg=0,st=fail:21.5
find parent
send: 8-8-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
send: 8-8-0-0 s=0,c=1,t=0,pt=7,l=5,sg=0,st=fail:21.5
send: 8-8-0-0 s=0,c=1,t=0,pt=7,l=5,sg=0,st=fail:21.5

No more log output from the Gateway.

Any clue ?

Mersing

Hello,

I received addition log on the GW:

ESP8266 MySensors Gateway
Connecting to WRT54G
.......Connected!
IP: 192.168.1.25
0;0;3;0;9;gateway started, id=0, parent=0, distance=0
0;0;3;0;9;Inclusion started by button.
0;0;3;0;5;1
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;9;Inclusion started by button.
0;0;3;0;5;0

"Inclusion started by button." are coming randomly (not triggered by node reboot ).

hek

Guys, would be great if you used the development branch instead.
Really need more testers of that code... also and any fixes for ESP8266/RF69 would be done in the dev-branch.

Mersing

Hello,

I'm now testing with 1.6, on GW and Node.

I'm trying to get familiar with the 1.6 changes.
On the node how can I setup the NODE ID ? ( it seems that gw.begin( NULL, 5) can't be used anymore).
On the Node side, I'm using DallasTemperatureSensor.ino.
Should I add presentation() call from Setup () ?

void setup()   { 
  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
  presentation();
}

I've setup the communication with RF24, as a first test.
From the GW

0;0;3;0;9;read: 5-5-0 s=255,c=0,t=17,pt=0,l=10,sg=0:1.6.0-beta
0;0;3;0;9;read: 5-5-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
0;0;3;0;9;read: 5-5-0 s=255,c=3,t=11,pt=0,l=18,sg=0:Temperature Senso
0;0;3;0;9;read: 5-5-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.1
0;0;3;0;9;read: 5-5-0 s=255,c=3,t=11,pt=0,l=18,sg=0:Temperature Senso
0;0;3;0;9;read: 5-5-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.1
0;0;3;0;9;read: 5-5-0 s=0,c=0,t=6,pt=0,l=0,sg=0:
0;0;3;0;9;read: 5-5-0 s=0,c=1,t=0,pt=7,l=5,sg=0:23.6
0;0;3;0;9;read: 5-5-0 s=0,c=1,t=0,pt=7,l=5,sg=0:23.7

Everything is working fine. (Seems the Node ID is coming from previous 1.5 upload, I've setup it to 5)

I've then replaced the radio by RF69 ones.
Below the changes in GatewayESP8266.ino

#define MY_RADIO_RFM69
#define MY_RF69_IRQ_PIN 4

Node ouput

Starting...
send: 5-5-0-0 s=255,c=0,t=17,pt=0,l=10,sg=0,st=fail:1.6.0-beta
send: 5-5-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=fail:0
send: 5-5-0-0 s=255,c=3,t=11,pt=0,l=18,sg=0,st=fail:Temperature Sensor
send: 5-5-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=fail:1.1
sensor started, id=5, parent=0, distance=1
send: 5-5-0-0 s=255,c=3,t=11,pt=0,l=18,sg=0,st=fail:Temperature Sensor
send: 5-5-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=fail:1.1
find parent
send: 5-5-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
send: 5-5-0-0 s=0,c=0,t=6,pt=0,l=0,sg=0,st=fail:
send: 5-5-0-0 s=0,c=1,t=0,pt=7,l=5,sg=0,st=fail:22.5
send: 5-5-0-0 s=0,c=1,t=0,pt=7,l=5,sg=0,st=fail:22.6

GW Output

0;0;3;0;9;Starting...
scandone
f 0, ....scandone
.add 0
aid 7
pm open phy_2,type:2 0 0
cnt 

connected with WRT54G, channel 6
dhcp client start...
.ip:192.168.1.25,mask:255.255.255.0,gw:192.168.1.1
.IP: 192.168.1.25
0;0;3;0;9;gateway started, id=0, parent=0, distance=0

ESP8266 MySensors Gateway
Connecting to WRT54G
sl
f -240, ....scandone
usl
sul 7 0
reconnect
rm 0
pm close 7 0 0/3399505
f 0, ....scandone
.add 0
aid 7
pm open phy_2,type:2 0 0
cnt 

connected with WRT54G, channel 6
dhcp client start...
..ip:192.168.1.25,mask:255.255.255.0,gw:192.168.1.1
.Connected!
IP: 192.168.1.25

Nothing more on the GW side.

Any idea ? Where (lib) can I start troubleshooting ?

Regards.

hek

Set static id with:

#define MY_NODE_ID xx

My guess is something goes wrong here:
https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/drivers/RFM69/RFM69.cpp#L47

Mersing

Hello,
I had a look at RFM69.cpp, bool RFM69::initialize function.
It a bit far away from my current skill to debug.
I've tried to display registers to check if they have been properly initialized.

  Serial.println( "bool RFM69::initialize" );
  Serial.println( "Read Registers" );
  Serial.print( "RegOpMode Read 0x01 : " );
  Serial.println( readReg( 0x01) );
  Serial.print( "RegDataModul Read 0x02 : " );
  Serial.println( readReg( 0x02) );
  Serial.print( "RegVersion Read 0x10 : " );
  Serial.println( readReg( 0x10) );
  Serial.print( "RegRssiValue Read 0x24) : " );
  Serial.println( readReg( 0x24) );
  Serial.println( "" );

Output is

0;0;3;0;9;Starting...
bool RFM69::initialize
Read Registers
RegOpMode Read 0x01 : 4
RegDataModul Read 0x02 : 0
RegVersion Read 0x10 : 36
RegRssiValue Read 0x24) : 56

scandone
f 0, ....scandone
.add 0
aid 7
pm open phy_2,type:2 0 0
cnt

Seems the registers are OK. However I can't go a step further.

I'm please to help for testing any new enhancement.

Regards,
Mersing.

hek

Hmm... I should really order a few RFM69 radios myself.

I only have a couple of Moteions. Doesn't help much if I would help out debugging ESP8266 with RFM69.

Mersing

You could maybe hack / re-use the radio from the Motino :smiley:

hek

Na... just have to wait for the china slow boat. Should be here before christmas :zzz:

Fabien

I have same bug : http://forum.mysensors.org/topic/2538/esp8266-and-rfm69w-loop-reboot

hek

Are you getting the same error in dev branch?

Fabien

With the last git developpement it works. except when a node start presentation, gateway reboot. And sometimes it reboots randomless.
node is a sensebender with MySensors 1.6 and gateway with 1.6 too.
Important : You have to define MY_RF69_IRQ_NUM = MY_RF26_IRQ_PIN on ESP8266

#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY   RF69_868MHZ
#define MY_RF69_IRQ_PIN 15
#define MY_RF69_SPI_CS 2
#define MY_RF69_IRQ_NUM 15

Result is

connected with PandoraBox_1BB657, channel 1
dhcp client start...
.ip:192.168.2.165,mask:255.255.255.0,gw:192.168.2.1
.IP: 192.168.2.165
0;0;3;0;9;Init complete, id=0, parent=0, distance=0
chg_B:-120

Soft WDT reset

ctx: cont 
sp: 3ffef9a0 end: 3ffefc60 offset: 01b0

>>>stack>>>
3ffefb50:  00000001 3ffefd00 3ffeff68 00000001  
3ffefb60:  00000024 3ffefd00 3ffeff68 402022f2  
3ffefb70:  3ffe8496 00000000 3ffefd00 40202378  
3ffefb80:  3ffe8496 00000000 3ffefd00 40202563  
3ffefb90:  3ffefd1e 00000001 3ffefd00 40202a43  
3ffefba0:  3fffdc20 00000000 3ffeec28 3ffefcd8  
3ffefbb0:  3fffdc20 3ffefd1d 3ffefd00 40202e0c  
3ffefbc0:  40209c8d 00000000 3ffeec28 40203ed1  
3ffefbd0:  00000000 00000002 3ffefe58 402039d0  
3ffefbe0:  00000000 3ffefd00 3ffeff68 40202338  
3ffefbf0:  40101500 402059d6 3ffeff50 3ffefc20  
3ffefc00:  3ffefc10 00000004 3ffefcf9 40202358  
3ffefc10:  3fffdc20 00000000 00000000 3ffeec30  
3ffefc20:  3fffdc20 00000000 3ffeec28 3ffeec30  
3ffefc30:  3fffdc20 00000000 3ffeec28 40203aee  
3ffefc40:  00000000 00000000 3ffeec28 402041a0  
3ffefc50:  00000000 00000000 3ffeec40 40100114  
<<<stack<<<
�!�L�<1���0;0;3;0;9;Starting gateway (RRNGE-, 1.6.0-beta)
0;0;3;0;9;Radio init successful.
scandone
state: 0 -> 2 (b0)
.state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
pm open phy_2,type:2 0 0
cnt 
chg_B:-60

connected with PandoraBox_1BB657, channel 1
dhcp client start...
.ip:192.168.2.165,mask:255.255.255.0,gw:192.168.2.1
.IP: 192.168.2.165
0;0;3;0;9;Init complete, id=0, parent=0, distance=0
chg_B:-120
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=0,pt=7,l=5,sg=0:24.6
0;0;3;0;9;read: 1-1-0 s=2,c=1,t=1,pt=2,l=2,sg=0:51
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=0,pt=7,l=5,sg=0:24.4

And something strange, I only recieve Humidity one time. (sensebender defaut sketch with FORCE_TRANSMIT_INTERVAL 0 )

Fabien

@hek you are right it works fine with

#define TIME_OUT 500

in https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/drivers/RFM69/RFM69.cpp#L47

0�~?�4�!�{�OAa�0;0;3;0;9;Starting gateway (RRNGE-, 1.6.0-beta)
0;0;3;0;9;Radio init successful.
scandone
state: 0 -> 2 (b0)
.state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
pm open phy_2,type:2 0 0
cnt 
chg_B:-60

connected with PandoraBox_1BB657, channel 1
dhcp client start...
.ip:192.168.2.165,mask:255.255.255.0,gw:192.168.2.1
.IP: 192.168.2.165
0;0;3;0;9;Init complete, id=0, parent=0, distance=0
chg_B:-120
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=0,pt=7,l=5,sg=0:24.8
0;0;3;0;9;read: 1-1-0 s=2,c=1,t=1,pt=2,l=2,sg=0:54
0;0;3;0;9;read: 1-1-0 s=255,c=0,t=17,pt=0,l=10,sg=0:1.6.0-beta
0;0;3;0;9;read: 1-1-0 s=255,c=4,t=0,pt=6,l=10,sg=0:FFFFFFFFFFFFFFFF0300
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=11,pt=0,l=17,sg=0:Sensebender Micro
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.4
0;0;3;0;9;read: 1-1-0 s=2,c=0,t=7,pt=0,l=0,sg=0:
0;0;3;0;9;read: 1-1-0 s=2,c=1,t=1,pt=2,l=2,sg=0:54
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=0,pt=7,l=5,sg=0:24.7
0;0;3;0;9;read: 1-1-0 s=2,c=1,t=1,pt=2,l=2,sg=0:50
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=0,pt=7,l=5,sg=0:24.7
0;0;3;0;9;read: 1-1-0 s=2,c=1,t=1,pt=2,l=2,sg=0:51
0;0;3;0;9;Client 0 connected
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=0,pt=7,l=5,sg=0:24.5
0;0;3;0;9;read: 1-1-0 s=2,c=1,t=1,pt=2,l=2,sg=0:50

I don't try with other timeout values.

hek

Ok, great. We need to increase timeout then.

Fabien

@hek Yes and perhaps a feature to set MY_RF69_IRQ_NUM = MY_RF26_IRQ_PIN when using ESP8266. Do You want to test other timeout values ? Is it critical ?

hek

@Fabien said:

MY_RF26_IRQ_PIN

I cannot find this defined anywhere...

ESP8266 gateway and sensor node not talking - noobie

24

11.7k

11.2k

113.1k