Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Raspberry data to > Mysensoors/Vera

Kurtsejr last edited by
I have a Raspberry Pi who interface a weather station, and I have made some perl code that make me read data from the weather station, put into a rrd database and then produce graphs to a web side. But since I have moved to mysensors and a using Vera controller, I want my weather data loaded in Vera. I see two possible ways of handling this:
1. Vera may read data directly via a web interface
2. I emulated a sensor and transfer data through the normal 2.4 Ghz interface.
Has anyone done this before, and are there any hint to help me ?

/Kurt
Reply Quote 0
1 Reply Last reply

1
Posts

878
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Balcony flower box irrigation
My Project • • pbw

2

0
Votes

2
Posts

20
Views

@pbw a gateway's function is to act as a gateway between the nodes and a controller. I don't think you will have all of the needed memory available to add logic to the gateway and you will make your solution very static. You can implemented your own lightway controller, just have a look at the Serial API. But controllers like Domoticz are lightweight and the already over a browser based interface. And most of them are easy to setup creating a much more versatile and dynamic solution.
HVAC Controller
My Project • • Michael Link

3

0
Votes

3
Posts

23
Views

We are of like minds, Don't like the cloud based controls (that's another discussion). In my case I have a Bryant/Connex system, heat pump, variable speed fan and 4 zones. There's a lot going on: the 4 zones creates 16 profiles. The fan speed for a profile will depend on the indoor and outdoor temperature. The thermal fluid pump also has to be controlled. A profile will have an optimal air pressure, so there's a sensor there. The controller works just fine not being connected to the cloud. But I want to set the parameters remotely, Bryant/Connex can do this. I also wnat the status of the various actuators and sensors to show up in Home Assistant. The signals sent over the RS422 are proprietary. My plan was to reverse-engineer the signals. After doing this I'll have to experiment to get the right mix of air pressue, fan speed and thermal fluid flow for each profile. I'd like to do the same for my AO Smith heat pump water heater. I'd like to follow your progress. OSD
MySensors Serial Gateway with USB 2.0
My Project • • DeepCore

2

1
Votes

2
Posts

23
Views

@DeepCore That is a need looking design. Did you consider using an alternative power supply other than usb? My Pi can't handle a lot of usb devices power wise, so I'm using a powered usb hub. But the wife doesn't like it, it's messy xd
nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

44

18
Votes

44
Posts

8019
Views

The output of the display could also be sent over serial, but the whole idea is you can walk around with the doctor and improve your results as you go.
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73895
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!

Raspberry data to > Mysensoors/Vera

Suggested Topics

Welcome
Announcements • • hek

Balcony flower box irrigation
My Project • • pbw

HVAC Controller
My Project • • Michael Link

MySensors Serial Gateway with USB 2.0
My Project • • DeepCore

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

Raspberry data to > Mysensoors/Vera

Suggested Topics

Welcome Announcements • • hek

Balcony flower box irrigation My Project • • pbw

HVAC Controller My Project • • Michael Link

MySensors Serial Gateway with USB 2.0 My Project • • DeepCore

nRF24Doctor My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

0Online

11.2kUsers

11.1kTopics

112.5kPosts

Welcome
Announcements • • hek

Balcony flower box irrigation
My Project • • pbw

HVAC Controller
My Project • • Michael Link

MySensors Serial Gateway with USB 2.0
My Project • • DeepCore

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts