Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Raspberry data to > Mysensoors/Vera

Kurtsejr last edited by
I have a Raspberry Pi who interface a weather station, and I have made some perl code that make me read data from the weather station, put into a rrd database and then produce graphs to a web side. But since I have moved to mysensors and a using Vera controller, I want my weather data loaded in Vera. I see two possible ways of handling this:
1. Vera may read data directly via a web interface
2. I emulated a sensor and transfer data through the normal 2.4 Ghz interface.
Has anyone done this before, and are there any hint to help me ?

/Kurt
Reply Quote 0
1 Reply Last reply

1
Posts

878
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

1

2
Votes

1
Posts

10
Views

No one has replied
nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

44

18
Votes

44
Posts

8024
Views

The output of the display could also be sent over serial, but the whole idea is you can walk around with the doctor and improve your results as you go.
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73900
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
A low cost energy meter
My Project • • OldSurferDude

7

1
Votes

7
Posts

44
Views

@OldSurferDude yes, you are correct. this sensor is capable of 50A continuous, which safely I would make it working at 40A max., but for such an important load as in your case I would go for a beefier one, like the ACS75x, 77x, but at this point I would also change the node's form factor for space and insulation reasons. On my application on the RV I have a max. curr. of 13A running on a AWG14-16 cable (European rules for RVs), so I did not ask myself too many questions beside, of course, safety. About the signal, it will be a sinusoidal signal swinging around Vcc/2. Vcc can be easily measured internally on the ATmega328. On all my DC sensors I measure Vcc at every loop, just before measuring the ADCs. Honestly, when the space is not an issue like in my RV, I would rather use a ring core current transformer, and I would get rid of noise, response time, power dissipation, but over all no need to cut any cable. Long story short, it has been a nice experiment and I used it for 6 months, and then I switched back to my RF-NANO based RS485-Modbus - Mysensors bridge connected to an off-the shelf power analyzer. Just for fun I attach a pic of my 12Vdc sensors installed on my RV. Forgive me for the spaghetti wiring on the right side, but this is an area that needs improvement.
Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

5

3
Votes

5
Posts

15
Views

@OldSurferDude thank you !

Raspberry data to > Mysensoors/Vera

Suggested Topics

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

A low cost energy meter
My Project • • OldSurferDude

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

17
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Raspberry data to > Mysensoors/Vera

Suggested Topics

Welcome Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway My Project • • fsgraz

nRF24Doctor My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

A low cost energy meter My Project • • OldSurferDude

Water Filtering and Sterilization and Hot Water Recirculation My Project • • fsgraz

17Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

A low cost energy meter
My Project • • OldSurferDude

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

17
Online

11.4k
Users

11.1k
Topics

112.7k
Posts