Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Repeater trouble

hyla last edited by

Hi,

looking into the problem with my just occasionally working repeaters. Using Yveaux' sniffer I find that my repeater (13)keeps asking for a parent:
13 255 mysensors 17 Cmd:INTERNAL, ReqAck:0, IsAck:0, Type:FIND_PARENT, Sns:255

Occasionally this is answered:
0 13 mysensors 18 Cmd:INTERNAL, ReqAck:0, IsAck:0, Type:FIND_PARENT_RESPONSE, Sns:255, Data:0 [BYTE]

Nevertheless, repeater node 13 keeps asking ...

An idea anyone? Repeater asks for parent, is answered but keeps asking?

Thanks for any help,
Christoph
Reply Quote 0
1 Reply Last reply

1
Posts

599
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

72
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

27
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }
Sensors and more
Hardware • • Robert Leverett

1

0
Votes

1
Posts

15
Views

No one has replied
Sleep mode for bmp280
Hardware • • fishermans

7

4
Votes

7
Posts

3281
Views

Just wanted to say thanks for this, it is still relevant and useful six years later !

Repeater trouble

Suggested Topics

Over the air updates
General Discussion • • ToSa

Which one should i choose? PIR or microwave sensor
Hardware • • h01

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Sensors and more
Hardware • • Robert Leverett

Sleep mode for bmp280
Hardware • • fishermans

56
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Repeater trouble

Suggested Topics

Over the air updates General Discussion • • ToSa

Which one should i choose? PIR or microwave sensor Hardware • • h01

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Sensors and more Hardware • • Robert Leverett

Sleep mode for bmp280 Hardware • • fishermans

56Online

11.4kUsers

11.1kTopics

112.7kPosts

Over the air updates
General Discussion • • ToSa

Which one should i choose? PIR or microwave sensor
Hardware • • h01

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Sensors and more
Hardware • • Robert Leverett

Sleep mode for bmp280
Hardware • • fishermans

56
Online

11.4k
Users

11.1k
Topics

112.7k
Posts