Delay after TSF:TRI:TSB
-
@mfalkvidd many thanks for the quick answer! :-)
Weirdly this behaviour only shows when I'm using the sleep mode. Also first time NACK appears is after the first Sleep - DEBUG after reset below, NACK at 8437. Any idea what i'm doing wrong or where i could fix it? :grimacing: :grimacing: many thanks in advance 🙂
⸮:⸮5 V=6 0 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.0 53 MCO:BGN:BFR NodeManager v1.7 LIB V=2.3.0 R=N E=- T=N A=A S=- B=- MOTION I=1 P=1 T=16 LDR I=2 P=16 T=23 RADIO...108 TSM:INIT 190 TSF:WUR:MS=0 215 TSM:INIT:TSP OK 235 TSF:SID:OK,ID=9 256 TSM:FPAR 305 TSF:MSG:SEND,9-9-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 2377 !TSM:FPAR:NO REPLY 2402 TSM:FPAR 2451 TSF:MSG:SEND,9-9-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 3278 TSF:MSG:READ,0-0-9,s=255,c=3,t=8,pt=1,l=1,sg=0:0 3334 TSF:MSG:FPAR OK,ID=0,D=1 4526 TSM:FPAR:OK 4542 TSM:ID 4556 TSM:ID:OK 4571 TSM:UPL 4589 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 4661 TSF:MSG:READ,0-0-9,s=255,c=3,t=25,pt=1,l=1,sg=0:1 4718 TSF:MSG:PONG RECV,HP=1 4747 TSM:UPL:OK 4765 TSM:READY:ID=9,PAR=0,DIS=1 4802 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100 4876 TSF:MSG:READ,0-0-9,s=255,c=3,t=15,pt=6,l=2,sg=0:0100 4941 TSF:MSG:SEND,9-9-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.0 5021 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0 5091 TSF:MSG:READ,0-0-9,s=255,c=3,t=6,pt=0,l=1,sg=0:M OK 5152 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=11,pt=0,l=5,sg=0,ft=0,st=OK:Testo 5232 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:2.0 PRES I=1 T=1 D=MOTION 5310 TSF:MSG:SEND,9-9-0-0,s=1,c=0,t=1,pt=0,l=6,sg=0,ft=0,st=OK:MOTION PRES I=2 T=16 D=LDR 5406 TSF:MSG:SEND,9-9-0-0,s=2,c=0,t=16,pt=0,l=3,sg=0,ft=0,st=OK:LDR READY 5494 MCO:REG:REQ 5525 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2 5597 TSF:MSG:READ,0-0-9,s=1,c=0,t=1,pt=0,l=6,sg=0:MOTION 5656 TSF:MSG:ACK 5675 TSF:MSG:READ,0-0-9,s=2,c=0,t=16,pt=0,l=3,sg=0:LDR 5732 TSF:MSG:ACK 5750 TSF:MSG:READ,0-0-9,s=255,c=3,t=27,pt=1,l=1,sg=0:1 5808 MCO:PIM:NODE REG=1 5832 MCO:BGN:STP MY I=9 M=1 INT P=3 M=1 INT P=2 M=255 5853 MCO:BGN:INIT OK,TSP=1 LDR I=2 V=60 %=5 SEND D=0 I=2 C=0 T=23 S= I=0 F=0.00 5928 TSF:MSG:SEND,9-9-0-0,s=2,c=1,t=23,pt=5,l=4,sg=0,ft=0,st=OK:5 SLEEP 20864s 6047 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255 6125 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500 6199 TSF:MSG:READ,0-0-9,s=2,c=1,t=23,pt=5,l=4,sg=0:5 6254 TSF:MSG:ACK 6699 TSF:TDI:TSL 6717 MCO:SLP:WUP=1 6735 TSF:TRI:TSB 8437 !TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:20864000 INT P=3, V=1 AWAKE MOTION I=1 P=3 V=1 SEND D=0 I=1 C=0 T=16 S= I=0 F=0.00 8536 TSF:MSG:SEND,9-9-0-0,s=1,c=1,t=16,pt=5,l=4,sg=0,ft=1,st=OK:1 LDR I=2 V=59 %=5 SEND D=0 I=2 C=0 T=23 S= I=0 F=0.00 8675 TSF:MSG:SEND,9-9-0-0,s=2,c=1,t=23,pt=5,l=4,sg=0,ft=0,st=OK:5 SLEEP 20864s 8796 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255 8869 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500 8943 TSF:MSG:READ,0-0-9,s=1,c=1,t=16,pt=5,l=4,sg=0:1 8998 TSF:MSG:ACK 9017 TSF:MSG:READ,0-0-9,s=2,c=1,t=23,pt=5,l=4,sg=0:5 9072 TSF:MSG:ACK 9443 TSF:TDI:TSL 9459 MCO:SLP:WUP=1 9480 TSF:TRI:TSB 11180 !TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:20864000 INT P=3, V=0 AWAKE MOTION I=1 P=3 V=0 SEND D=0 I=1 C=0 T=16 S= I=0 F=0.00 11280 TSF:MSG:SEND,9-9-0-0,s=1,c=1,t=16,pt=5,l=4,sg=0,ft=1,st=OK:0 LDR I=2 V=60 %=5 SEND D=0 I=2 C=0 T=23 S= I=0 F=0.00 11421 TSF:MSG:SEND,9-9-0-0,s=2,c=1,t=23,pt=5,l=4,sg=0,ft=0,st=OK:5 SLEEP 20864s 11542 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255 11620 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500 11696 TSF:MSG:READ,0-0-9,s=1,c=1,t=16,pt=5,l=4,sg=0:0 11751 TSF:MSG:ACK 11771 TSF:MSG:READ,0-0-9,s=2,c=1,t=23,pt=5,l=4,sg=0:5 11827 TSF:MSG:ACK 12197 TSF:TDI:TSLHere the DEBUG if I exclude sleep (to --> //node.setSleepDays(1);) - then the sensor sends it's msg. fast and happily..
⸮:⸮5 V=6 0 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.0 53 MCO:BGN:BFR NodeManager v1.7 LIB V=2.3.0 R=N E=- T=N A=A S=- B=- MOTION I=1 P=1 T=16 LDR I=2 P=16 T=23 RADIO...108 TSM:INIT 190 TSF:WUR:MS=0 215 TSM:INIT:TSP OK 235 TSF:SID:OK,ID=9 256 TSM:FPAR 305 TSF:MSG:SEND,9-9-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 376 TSF:MSG:READ,0-0-9,s=255,c=3,t=8,pt=1,l=1,sg=0:0 432 TSF:MSG:FPAR OK,ID=0,D=1 2377 TSM:FPAR:OK 2394 TSM:ID 2408 TSM:ID:OK 2422 TSM:UPL 2441 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 2512 TSF:MSG:READ,0-0-9,s=255,c=3,t=25,pt=1,l=1,sg=0:1 2570 TSF:MSG:PONG RECV,HP=1 2598 TSM:UPL:OK 2617 TSM:READY:ID=9,PAR=0,DIS=1 2654 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100 2727 TSF:MSG:READ,0-0-9,s=255,c=3,t=15,pt=6,l=2,sg=0:0100 2793 TSF:MSG:SEND,9-9-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.0 2873 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0 2942 TSF:MSG:READ,0-0-9,s=255,c=3,t=6,pt=0,l=1,sg=0:M OK 3035 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=11,pt=0,l=5,sg=0,ft=0,st=OK:Testo 3112 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:2.0 PRES I=1 T=1 D=MOTION 3190 TSF:MSG:SEND,9-9-0-0,s=1,c=0,t=1,pt=0,l=6,sg=0,ft=0,st=OK:MOTION PRES I=2 T=16 D=LDR 3289 TSF:MSG:SEND,9-9-0-0,s=2,c=0,t=16,pt=0,l=3,sg=0,ft=0,st=OK:LDR READY 3377 MCO:REG:REQ 3407 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2 3479 TSF:MSG:READ,0-0-9,s=255,c=3,t=27,pt=1,l=1,sg=0:1 3536 MCO:PIM:NODE REG=1 3561 MCO:BGN:STP MY I=9 M=1 INT P=3 M=1 INT P=2 M=255 3581 MCO:BGN:INIT OK,TSP=1 LDR I=2 V=57 %=5 SEND D=0 I=2 C=0 T=23 S= I=0 F=0.00 3657 TSF:MSG:SEND,9-9-0-0,s=2,c=1,t=23,pt=5,l=4,sg=0,ft=0,st=OK:5 INT P=3, V=1 MOTION I=1 P=3 V=1 SEND D=0 I=1 C=0 T=16 S= I=0 F=0.00 8374 TSF:MSG:SEND,9-9-0-0,s=1,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1 INT P=3, V=0 MOTION I=1 P=3 V=0 SEND D=0 I=1 C=0 T=16 S= I=0 F=0.00 12304 TSF:MSG:SEND,9-9-0-0,s=1,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:0 -
@fausti sorry, I don't know what nodemanager does behind the scene so there isn't really a way for me to troubleshoot.
What is powered through pin 6?
@mfalkvidd thanks again!! :-)
Yeah.. went through the whole NodeManager Library, tried many things, but couldn’t find the reason for this behaviour. probably I must build my sketch again on foot – without NodeManager, hoped it could save me some time. ^^
PIN 6 powers an LDR together with PIN 5, read by PIN A0. But when I exclude all corresponding parts and even remove the hardware (10k + LDR) it won’t help.Oddly sleeping Time (MCO:SLP:MS=20864000 has the same value as the number after NACK (st=NACK:20864000). If I change the sleep time (e.g. from 1 day to 60 sec) both values are changing equally to the equivalent value in ms.
@henrik-nielsen had a similar problem (maybe the same) https://forum.mysensors.org/topic/9598/smartsleep-wake-up-message-always-get-nack
Later I’ll try the fix described by @berkseo.Thanks! :grinning:
-
@mfalkvidd thanks again!! :-)
Yeah.. went through the whole NodeManager Library, tried many things, but couldn’t find the reason for this behaviour. probably I must build my sketch again on foot – without NodeManager, hoped it could save me some time. ^^
PIN 6 powers an LDR together with PIN 5, read by PIN A0. But when I exclude all corresponding parts and even remove the hardware (10k + LDR) it won’t help.Oddly sleeping Time (MCO:SLP:MS=20864000 has the same value as the number after NACK (st=NACK:20864000). If I change the sleep time (e.g. from 1 day to 60 sec) both values are changing equally to the equivalent value in ms.
@henrik-nielsen had a similar problem (maybe the same) https://forum.mysensors.org/topic/9598/smartsleep-wake-up-message-always-get-nack
Later I’ll try the fix described by @berkseo.Thanks! :grinning:
-
@mfalkvidd thanks again!! :-)
Yeah.. went through the whole NodeManager Library, tried many things, but couldn’t find the reason for this behaviour. probably I must build my sketch again on foot – without NodeManager, hoped it could save me some time. ^^
PIN 6 powers an LDR together with PIN 5, read by PIN A0. But when I exclude all corresponding parts and even remove the hardware (10k + LDR) it won’t help.Oddly sleeping Time (MCO:SLP:MS=20864000 has the same value as the number after NACK (st=NACK:20864000). If I change the sleep time (e.g. from 1 day to 60 sec) both values are changing equally to the equivalent value in ms.
@henrik-nielsen had a similar problem (maybe the same) https://forum.mysensors.org/topic/9598/smartsleep-wake-up-message-always-get-nack
Later I’ll try the fix described by @berkseo.Thanks! :grinning:
-
@fausti interesting that the sleep and the nack has the same value. Maybe something gets overwritten in memory.
@mfalkvidd @fausti no, this is normal the smartsleep log:
6047 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255==> smart sleep enabled, IRQ on pin 1 set, going to sleep for 20864000 ms
6125 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500==> I_PRE_SLEEP_NOTIFICATION, 500ms to process any incoming message before going to seep
6199 TSF:MSG:READ,0-0-9,s=2,c=1,t=23,pt=5,l=4,sg=0:5 6254 TSF:MSG:ACK 6699 TSF:TDI:TSL 6717 MCO:SLP:WUP=1 6735 TSF:TRI:TSB==> sleep interrupted by IRQ 1
8437 !TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:20864000==> I_POST_SLEEP_NOTIFICATION, node was sleeping for 20864000ms (but sleep was interrupted)
-
@mfalkvidd @fausti no, this is normal the smartsleep log:
6047 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255==> smart sleep enabled, IRQ on pin 1 set, going to sleep for 20864000 ms
6125 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500==> I_PRE_SLEEP_NOTIFICATION, 500ms to process any incoming message before going to seep
6199 TSF:MSG:READ,0-0-9,s=2,c=1,t=23,pt=5,l=4,sg=0:5 6254 TSF:MSG:ACK 6699 TSF:TDI:TSL 6717 MCO:SLP:WUP=1 6735 TSF:TRI:TSB==> sleep interrupted by IRQ 1
8437 !TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:20864000==> I_POST_SLEEP_NOTIFICATION, node was sleeping for 20864000ms (but sleep was interrupted)
-
...but, the delay between TSB and SEND is a bit odd;
9480 TSF:TRI:TSB 11180 !TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=NACK:20864000Enabling
MY_DEBUG_VERBOSE_RF24could eventually give some hints.FYI: I tried with both, 2.3.0 and 2.3.1-beta (incl. CE fix), on non-amplified and PA+LNA modules - I do not see any delay between TSB and SEND
6973 MCO:SLP:MS=5000,SMS=1,I1=1,M1=1,I2=255,M2=255 6979 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500 7486 TSF:TDI:TSL 7487 MCO:SLP:WUP=1 7489 TSF:TRI:TSB 7492 TSF:MSG:SEND,100-100-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=OK:5000I assume you have a power issue, a bad module - or an artifact originating from the nodemanager?
-
@Yveaux sensor is using standard NRF24L01+ (only the gw uses pa+lna - but I guess that won't be an issue?)
@tekka did you use the same sketch? You mentioned smartsleep, I haven't enabled that.. I'll try
MY_DEBUG_VERBOSE_RF24later, use a fresh NodeManager and will check all my hardware again and I still have to try that fix: https://forum.mysensors.org/topic/9598/smartsleep-wake-up-message-always-get-nack
I've build more than one sensor and all of them are showing that delay - using different power sources and I also tried different capacitor. Maybe after all it's the gw.. but can't think of a reason why sleeping would cause that behavior at gw.I'll report later - Thanks for the quick help!!
-
@Yveaux sensor is using standard NRF24L01+ (only the gw uses pa+lna - but I guess that won't be an issue?)
@tekka did you use the same sketch? You mentioned smartsleep, I haven't enabled that.. I'll try
MY_DEBUG_VERBOSE_RF24later, use a fresh NodeManager and will check all my hardware again and I still have to try that fix: https://forum.mysensors.org/topic/9598/smartsleep-wake-up-message-always-get-nack
I've build more than one sensor and all of them are showing that delay - using different power sources and I also tried different capacitor. Maybe after all it's the gw.. but can't think of a reason why sleeping would cause that behavior at gw.I'll report later - Thanks for the quick help!!
-
@Yveaux sensor is using standard NRF24L01+ (only the gw uses pa+lna - but I guess that won't be an issue?)
@tekka did you use the same sketch? You mentioned smartsleep, I haven't enabled that.. I'll try
MY_DEBUG_VERBOSE_RF24later, use a fresh NodeManager and will check all my hardware again and I still have to try that fix: https://forum.mysensors.org/topic/9598/smartsleep-wake-up-message-always-get-nack
I've build more than one sensor and all of them are showing that delay - using different power sources and I also tried different capacitor. Maybe after all it's the gw.. but can't think of a reason why sleeping would cause that behavior at gw.I'll report later - Thanks for the quick help!!
-
@fausti Can you re-test your setup with this patch (ideally, update GW and nodes): https://github.com/tekka007/MySensors/tree/RF24STDBYTiming - I've added a delay after setting the radio in standby mode.
@tekka WOW!! Your fix works like a dream - can't thank you enough! :pray: :tada:
For now I just used your patch at the sensor - but it allready runs perfectly - no lag/no NACK (see DEBUG below).
So the radio needs more time to settle? How long did you set the delay?Many many thanks to @tekka and to you all for helping that fast and professional!!
[For so many hours I tried figuring out where the problem lies.. at least I know that library better now ^^ ]
0 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.3.1-beta 59 MCO:BGN:BFR NodeManager v1.7 LIB V=2.3.1-beta R=N E=- T=N A=A S=- B=- MOTION I=1 P=1 T=16 LDR I=2 P=16 T=23 RADIO...118 TSM:INIT 200 TSF:WUR:MS=0 223 TSM:INIT:TSP OK 245 TSF:SID:OK,ID=9 266 TSM:FPAR 315 TSF:MSG:SEND,9-9-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 1208 TSF:MSG:READ,0-0-9,s=255,c=3,t=8,pt=1,l=1,sg=0:0 1265 TSF:MSG:FPAR OK,ID=0,D=1 2390 TSM:FPAR:OK 2406 TSM:ID 2420 TSM:ID:OK 2435 TSM:UPL 2453 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 2525 TSF:MSG:READ,0-0-9,s=255,c=3,t=25,pt=1,l=1,sg=0:1 2582 TSF:MSG:PONG RECV,HP=1 2611 TSM:UPL:OK 2629 TSM:READY:ID=9,PAR=0,DIS=1 2666 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100 2740 TSF:MSG:READ,0-0-9,s=255,c=3,t=15,pt=6,l=2,sg=0:0100 2805 TSF:MSG:SEND,9-9-0-0,s=255,c=0,t=17,pt=0,l=10,sg=0,ft=0,st=OK:2.3.1-beta 2891 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0 2961 TSF:MSG:READ,0-0-9,s=255,c=3,t=6,pt=0,l=1,sg=0:M OK 3022 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=11,pt=0,l=5,sg=0,ft=0,st=OK:Testo 3102 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:2.0 PRES I=1 T=1 D=MOTION 3180 TSF:MSG:SEND,9-9-0-0,s=1,c=0,t=1,pt=0,l=6,sg=0,ft=0,st=OK:MOTION PRES I=2 T=16 D=LDR 3276 TSF:MSG:SEND,9-9-0-0,s=2,c=0,t=16,pt=0,l=3,sg=0,ft=0,st=OK:LDR READY 3364 MCO:REG:REQ 3395 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2 3467 TSF:MSG:READ,0-0-9,s=255,c=3,t=27,pt=1,l=1,sg=0:1 3524 MCO:PIM:NODE REG=1 3551 MCO:BGN:STP MY I=9 M=1 INT P=3 M=1 INT P=2 M=255 3569 MCO:BGN:INIT OK,TSP=1 LDR I=2 V=302 %=29 SEND D=0 I=2 C=0 T=23 S= I=0 F=0.00 3645 TSF:MSG:SEND,9-9-0-0,s=2,c=1,t=23,pt=5,l=4,sg=0,ft=0,st=OK:29 SLEEP 20864s 3768 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255 3846 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500 4419 TSF:TDI:TSL 4435 MCO:SLP:WUP=1 4456 TSF:TRI:TSB 4483 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=OK:20864000 INT P=3, V=1 AWAKE MOTION I=1 P=3 V=1 SEND D=0 I=1 C=0 T=16 S= I=0 F=0.00 4579 TSF:MSG:SEND,9-9-0-0,s=1,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:1 LDR I=2 V=284 %=27 SEND D=0 I=2 C=0 T=23 S= I=0 F=0.00 4718 TSF:MSG:SEND,9-9-0-0,s=2,c=1,t=23,pt=5,l=4,sg=0,ft=0,st=OK:27 SLEEP 20864s 4841 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255 4919 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500 5494 TSF:TDI:TSL 5511 MCO:SLP:WUP=1 5531 TSF:TRI:TSB 5558 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=33,pt=5,l=4,sg=0,ft=0,st=OK:20864000 INT P=3, V=0 AWAKE MOTION I=1 P=3 V=0 SEND D=0 I=1 C=0 T=16 S= I=0 F=0.00 5654 TSF:MSG:SEND,9-9-0-0,s=1,c=1,t=16,pt=5,l=4,sg=0,ft=0,st=OK:0 LDR I=2 V=295 %=28 SEND D=0 I=2 C=0 T=23 S= I=0 F=0.00 5793 TSF:MSG:SEND,9-9-0-0,s=2,c=1,t=23,pt=5,l=4,sg=0,ft=0,st=OK:28 SLEEP 20864s 5916 MCO:SLP:MS=20864000,SMS=1,I1=1,M1=1,I2=255,M2=255 5994 TSF:MSG:SEND,9-9-0-0,s=255,c=3,t=32,pt=5,l=4,sg=0,ft=0,st=OK:500 6569 TSF:TDI:TSL -
@tekka This patch is not compiling correctly for ESP8266Gateway when using Wemos D1 Mini in the board manager, nor does it compile when the NodeMCU 1.0 board is selected either.
-
@rayne it compiled fine when the change was merged into MySensors.
Could you post the error message you're getting? -
@mfalkvidd Strange, when I compile for a arduino pro mini sensor, it compiles fine. However if I try to compile the esp8266gateway for a Wemos D1 Mini, the compiler complains about a file with no such directory.
-
@mfalkvidd Ahhhh, that was it. I was still on 2.3.0 of the esp8266 core. Once I upgraded to 2.4.2 it compiled fine and was able to find gdb_hooks.h. I think I was on the older version due to some compatibility issues I had when I was making a WiFi Jammer for a buddy of mine some time ago. Hey thanks for your help @mfalkvidd . You are the man!
