Problems with Nano + W5100 (funduino) + NRF24L01 gateway - no access.



  • Hi,

    i built the following:

    IMG_6545.JPG
    IMG_6546.JPG
    IMG_6547.JPG
    IMG_6548.JPG
    IMG_6549.JPG
    IMG_6550.JPG
    IMG_6551.JPG

    With the following code:

    // Enable debug prints to serial monitor
    #define MY_DEBUG
    
    // Enable and select radio type attached
    #define MY_RADIO_RF24
    //#define MY_RADIO_NRF5_ESB
    //#define MY_RADIO_RFM69
    //#define MY_RADIO_RFM95
    
    // Enable gateway ethernet module type
    #define MY_GATEWAY_W5100
    
    // W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
    //#define MY_W5100_SPI_EN 4
    
    // Enable Soft SPI for NRF radio (note different radio wiring is required)
    // The W5100 ethernet module seems to have a hard time co-operate with
    // radio on the same spi bus.
    #if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
    #define MY_SOFTSPI
    #define MY_SOFT_SPI_SCK_PIN 14
    #define MY_SOFT_SPI_MISO_PIN 16
    #define MY_SOFT_SPI_MOSI_PIN 15
    #endif
    
    // When W5100 is connected we have to move CE/CSN pins for NRF radio
    #ifndef MY_RF24_CE_PIN
    #define MY_RF24_CE_PIN 5
    #endif
    #ifndef MY_RF24_CS_PIN
    #define MY_RF24_CS_PIN 6
    #endif
    
    // Enable UDP communication
    //#define MY_USE_UDP  // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below
    
    // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
    #define MY_IP_ADDRESS 192,168,80,15
    
    // If using static ip you can define Gateway and Subnet address as well
    //#define MY_IP_GATEWAY_ADDRESS 192,168,80,1
    #define MY_IP_SUBNET_ADDRESS 255,255,255,0
    
    // Renewal period if using DHCP
    //#define MY_IP_RENEWAL_INTERVAL 60000
    
    // The port to keep open on node server mode / or port to contact in client mode
    #define MY_PORT 5003
    
    // Controller ip address. Enables client mode (default is "server" mode).
    // Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
    //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254
    //#define MY_CONTROLLER_URL_ADDRESS "my.controller.org"
    
    // The MAC address can be anything you want but should be unique on your network.
    // Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
    // Note that most of the Arduino examples use  "DEAD BEEF FEED" for the MAC address.
    #define MY_MAC_ADDRESS 0x00, 0x40, 0xFD, 0xEF, 0x35, 0x76
    
    
    // Enable inclusion mode
    #define MY_INCLUSION_MODE_FEATURE
    // Enable Inclusion mode button on gateway
    #define MY_INCLUSION_BUTTON_FEATURE
    // Set inclusion mode duration (in seconds)
    #define MY_INCLUSION_MODE_DURATION 60
    // Digital pin used for inclusion mode button
    #define MY_INCLUSION_MODE_BUTTON_PIN  3
    
    // Set blinking period
    #define MY_DEFAULT_LED_BLINK_PERIOD 300
    
    // Flash leds on rx/tx/err
    // Uncomment to override default HW configurations
    #define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
    #define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
    #define MY_DEFAULT_TX_LED_PIN  9  // Transmit led pin
    
    #if defined(MY_USE_UDP)
    #include <EthernetUdp.h>
    #endif
    #include <SPI.h>
    #include <Ethernet.h>
    #include <MySensors.h>
    
    void setup()
    {
      // Setup locally attached sensors
    }
    
    void presentation()
    {
      // Present locally attached sensors here
    }
    
    void loop()
    {
      // Send locally attached sensors data here
    }
    
    

    Serial monitor shows:

    0 MCO:BGN:INIT GW,CP=RNNGA---,FQ=16,REL=255,VER=2.3.2
    4 TSM:INIT
    5 TSF:WUR:MS=0
    12 TSM:INIT:TSP OK
    13 TSM:INIT:GW MODE
    15 TSM:READY:ID=0,PAR=0,DIS=0
    18 MCO:REG:NOT NEEDED
    642 GWT:TIN:IP=255.255.255.255
    1644 MCO:BGN:STP
    1646 MCO:BGN:INIT OK,TSP=1
    1648 TSM:READY:NWD REQ
    1653 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
    

    Log parser shows:

    Node Id	Child Sensor	Command Type	Echo Req/Resp	Type	Payload	Description
    0 MCO:BGN:INIT GW,CP=RNNGA---,FQ=16,REL=255,VER=2.3.2	Core initialization of GW, with capabilities RNNGA---, CPU frequency 16 MHz, library version 2.3.2, release 255
    4 TSM:INIT	Transition to Init state
    5 TSF:WUR:MS=0	Wait until transport ready, timeout 0
    12 TSM:INIT:TSP OK	Transition to Init state:TSP OK
    13 TSM:INIT:GW MODE	Transition to Init state:GW MODE
    15 TSM:READY:ID=0,PAR=0,DIS=0	Transport ready, node id 0, parent node id 0, distance to GW is 0
    18 MCO:REG:NOT NEEDED	No registration needed (i.e. GW)
    Unknown	642 GWT:TIN:IP=255.255.255.255	
    1644 MCO:BGN:STP	Callback setup()
    1646 MCO:BGN:INIT OK,TSP=1	Core initialized, transport status 1, (1=initialized, 0=not initialized, NA=not available)
    1648 TSM:READY:NWD REQ	Send transport network discovery request
    1653 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:	Sent Message without radio ACK
    Sender: 0
    Last Node: 0
    Next Node: 255
    Destination: 255
    Sensor Id: 255
    Command: INTERNAL
    Message Type:I_DISCOVER_REQUEST
    Payload Type: P_STRING
    Payload Length: 0
    Signing: 0
    Failed uplink counter: 0
    Status: OK (OK=success, NACK=no radio ACK received)
    Payload:
    

    but nothing:

    • can't ping to it.
    • arp -a shows the address, but no the mac.

    ANy hint?


  • Mod

    For some reason the Gateway uses IP=255.255.255.255 (which is not a valid IP address) instead of the one you specified.

    There is plenty of free ram after compiling the sketch, so ram shouldn't be a problem.

    There have been a few similar reports earlier. https://forum.mysensors.org/post/82366 seems to be the only one that has a suggested solution.

    Which version of the Arduino IDE and which AVR board version are you using?


Log in to reply
 

Suggested Topics

  • 3
  • 10
  • 2
  • 3
  • 4
  • 15

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts