💬 AC-DC double solid state relay module

[okos]

Thanx for the answers
This is not good news from the switch does not work without a server. Mr.const, Do you use esp8266 in domoticz to control the light?

edit: hek, I not noticed your post.
What changes adding this?

#define MY_TRANSPORT_DONT_CARE_MODE
#define MY_PARENT_NODE_ID 0```

[hek]

@okos said:

What changes adding this?

It disables the transport sanity check at startup.

[mr_const]

@hek

@hek said:

You can disable this behaviour by defining:

#define MY_TRANSPORT_DONT_CARE_MODE
#define MY_PARENT_NODE_ID 0

This is a really good news, I'll give it a try to check if it works correctly with controller and when controller is lost.

[okos]

@hek said:

You can disable this behaviour by defining:

#define MY_TRANSPORT_DONT_CARE_MODE
#define MY_PARENT_NODE_ID 0

sorry for the ridiculous question but I have to enter into a sketch? or MyConfig.h?

[hek]

In the sketch before including MySensors.h

[mr_const]

@hek

@hek said:

You can disable this behaviour by defining:

#define MY_TRANSPORT_DONT_CARE_MODE
#define MY_PARENT_NODE_ID 0

Tried it. Doesn't work. Btw, I searched all mysensors sources (2.0) and didn't find any use of a MY_TRANSPORT_DONT_CARE_MODE definition.

[hek]

@mr_const said:

MY_TRANSPORT_DONT_CARE_MODE

Sorry, yes, It's all in the development branch:

https://github.com/mysensors/MySensors/search?utf8=✓&q=MY_TRANSPORT_DONT_CARE_MODE

[okos]

It possible implement this option in mysensors 2.0 ?

[mfalkvidd]

@okos it will be included in the next release yes.

[okos]

Hello.
I tried to upload my two boards ( arduino pro mini 8Mhz , 3,3 V ) modified sketches but returned to sketch Nca78 (with DS18B20), unfortunately, does not operate a physical switch. Sometimes phisical switch changes state in domoticz ( not every time ) but relays do not change state.
Switching on and switching off the lights of domoticz changes state relay without a problem.
What could be wrong ?

[ludoarchi]

Hi

Does somebody can post a picture of the back side please.

Thinks

[okos]

@ludoarchi ![alt text]

[ludoarchi]

@okos thinks !

[Nca78]

That's where the biggest problem is on this board. I think the previous revision without the DS18 is safer, here there is less than 2mm creepage/clearance between main and low voltage traces and solder points, not enough :(

There's also problem of mixing both main/low voltage everywhere in the board like near the NRF24.

[ludoarchi]

Hi
Noob questions sorry !
1/ Can i used it with 3way switches ?
2/ what are the pins 7 GND and 4 for ?
Thinks

[mr_const]

@ludoarchi

@ludoarchi said:

2/ what are the pins 7 GND and 4 for ?

7 and 4 pins are mapped to 7 and 4 in/out of an arduino module. GND is for ground. These pins could be used to manually control relay state.

[ludoarchi]

@mr_const ok i understand ! Thinks

[rozpruwacz]

hi, great project. I have one idea, is it possible to add current and voltage measurement ?

[Sander Crombeen]

Ordered all the components for this project but now i see there are 12 v solid state relays on the list?? mine is not working, does it not need to have 5V version??

[Achim]

Hello,
one question to the SSR Relay. The Arduino works with 5V, the SSR in the BOM is a 12V type. Is this a mistake? According to the Datasheet of the relay, the 12V type has an operating range from 9,6v to 14,4V