Brand new Vera controller



  • I finally received my new Vera Plus controller. I am looking through the instructions on setting things up for MySensors devices and have some questions. First thing I did was a firmware upgrade to 1.7.2138, which it says is the latest firmware. Now I am going through the information on this page https://www.mysensors.org/controller/vera to install the plugin. FIrst, I would assume that I would install the files for UI7. When I go to the git repo there are a number of files and folders, some of which look specific to sensors that I do not have such as Multimeter, WindSensor and Barometer. I am running a serial gateway, so I am assuming that I need to download the arduino files, but do I need them all? Also, I would assume that I would only need to download the other folders for things like the WindSensor as needed if I were to implement those devices. I just don't want to upload more than I need that will clutter up my Vera from the get go.

    Any help with getting me set up is appreciated.



  • So I just uploaded all of the arduino files and created the device. The next step says "Click the Reload button in the upper right corner of the Vera dashboard to create the Arduino root plugin device." There is no reload button on my dashboard page.
    0_1482072942614_upload-23838ca9-0597-4b15-b495-b05d231dbbe4

    I am slightly stuck here. Also, I was reading that there are issues with the serial gateway and UI7, is this still the case?


  • Hero Member

    You can restart the luup engine on the VeraPlus by going to Apps -> develop apps ->serial port configuration and hitt Save.

    Another optin is a button in Settings -> Z-Wave Settings -> "Advanced tab" -> Reload engine



  • @korttoma Thanks. I am just in the beginning stages of getting things set up, so I am sure I will have more questions.


  • Hero Member

    @dbemowsk feel free to ask but if it is taking to long to get the answer you should try the Vera forum

    These are the files you need:

    D_Arduino1.json
    D_Arduino1.xml
    D_ArduinoNode1.json
    D_ArduinoNode1.xml
    D_ArduinoRelay1.json
    D_ArduinoRelay1.xml
    I_Arduino1.xml
    L_Arduino.lua
    S_Arduino.xml
    S_ArduinoNode.xml

    The other files are only needed if you have that specific MySensors device type in use.

    Did you manage to create the MySensors plugin main device?
    If you did you should see some error on the top of the screen that you need to setup the serial port for this device.



  • @korttoma I did get the plugin created and I do see the message to set up the serial port. I went to Develop Apps>Serial Port Configuration and it shows nothing available. I have an FTDI adapter connected to a 4 port hub. Currently the FTDI adapter is the only thing plugged into the hub. When I SSH into the unit and issue this:

    dmesg | grep USB
    

    I get this:

    [    4.012000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
    [    4.040000] hub 1-0:1.0: USB hub found
    [    4.064000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
    [    4.080000] hub 2-0:1.0: USB hub found
    [    4.120000] usbserial: USB Serial support registered for generic
    [    4.528000] usb 1-2: new high-speed USB device number 2 using xhci-hcd
    [    5.860000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [   17.564000] usbserial: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
    [   17.600000] usbserial: USB Serial support registered for cp210x
    [   17.632000] usbserial: USB Serial support registered for FTDI USB Serial Device
    [   17.712000] usbserial: USB Serial support registered for Keyspan - (without firmware)
    [   17.728000] usbserial: USB Serial support registered for Keyspan 1 port adapter
    [   17.744000] usbserial: USB Serial support registered for Keyspan 2 port adapter
    [   17.760000] usbserial: USB Serial support registered for Keyspan 4 port adapter
    [   17.788000] usbserial: USB Serial support registered for MCT U232
    [   17.888000] usbserial: USB Serial support registered for pl2303
    [   17.948000] usbserial: USB Serial support registered for Sierra USB modem
    [   18.172000] usbserial: USB Serial support registered for IPWireless converter
    [   18.216000] usbserial: USB Serial support registered for GSM modem (1-port)
    [   18.264000] usbserial: USB Serial support registered for Qualcomm USB modem
    

    I thought it was the pl2303, but when I checked the "/dev" folder, I did not see a ttyUSBx device, so I knew that couldn't be it. I plugged a power adapter into the hub and tried again, this time when I did:

    dmesg | grep tty
    

    I got this:

    [ 1703.300000] usb 1-1.1: pl2303 converter now attached to ttyUSB0
    

    Then when I went back to Vera serial port configuration I saw it. I set the baud to 115200, and "Used By Device" to "MySensors Plugin[]"

    Now when I go to Devices, I see the MySensors Plugin "Connected to: 20(115200)". Now I am not sure how to add my device nodes.


  • Hero Member

    @dbemowsk said:

    MySensors Plugin "Connected to: 20(115200)"

    So far so good ๐Ÿ˜‰

    You should see the text "Press start for inclusion" and a Start and Stop button on the Plugin Main Device. Now all you need to do is push the "Start" button to start "inclusion mode" and then you restart your sensor so that it can present itself.

    If new sensors are detected when in inclusion mode you should see the text "X devices found" Inclusion mode is active for 1 min. If new sensors are found the Vera will automatically restart the luup engine and create the devices. Wait until you are sure the restart is done and then "ctrl + F5" to refresh your browser.
    Your new devices should now be found under -> Devices -> No Room. If not all child sensors are found just try the inclusion again (sometimes I restart the node a few times while the inclusion mode is active so that all devices are picked up).

    Good luck ๐Ÿ˜‰



  • @korttoma So I see this when I press the arrow next to the plugin icon under devices:
    0_1482191806960_upload-d5a6e29d-95c0-4cfb-b69e-bfb2ba193105
    So I click the arrow next to settings and I see this, which is what you are talking about:
    0_1482191925426_upload-bb13f11e-7656-47b0-b944-bd538c100cdc
    When I press Start I get this error:
    0_1482192017041_upload-4f04b3f4-c957-49a2-b6e0-42c11f12f2b5

    One other thing, I cannot change the Unit selector just above the Start/Stop buttons. I don't know if these two things are related in any way, but thought I'd mention it in case they are.


  • Hero Member

    Hi @dbemowsk this does not seem right at all.

    Here is what it should look like:

    The Plugin Main device looks like this with the Start/Stop button, you should be able to operate it from here:
    0_1482210522232_upload-21bcd566-efbf-471e-9fd1-71b7cba5708a

    Under settings it should look like this:
    0_1482210573835_upload-809306f4-08ae-4ed3-a29e-a99387f0d318

    And when you press start it should look like this:
    0_1482210608095_upload-9baeb4ae-44d0-4a08-9bbb-4a54dcf07c5a

    Are you sure you used the files from here?

    Try uploading the files again and then try the luup reload a few times and then browser refresh.


  • Admin

    @dbemowsk You might want to try some of the steps detailed in this thread https://forum.mysensors.org/topic/5289/ui5-to-ui7-update/14 to confirm that you have the right versions of the plugin files installed.



  • @korttoma One other thing I am seeing is an error at the top of the screen.

    GET_LANG(system_error,System error) : Device: 8. Fail to load implementation file D_Codeset_1104.xml.lzo

    My Vera firmware version is 1.7.2138 if that makes a difference.

    I downloaded the UI7 files from the same github link that you posted. I even tried the steps from the link that blacey posted. This to me seemed like a slightly different set of plugin files. The zip file that I downloaded from https://github.com/mysensors/Vera/tree/UI7 created a folder named "Vera-UI7". The one I downloaded from blacey's link, https://api.github.com/repos/mysensors/Vera/zipball/UI7 created a folder named "mysensors-Vera-73ed9b7". I used meld to diff the 2 folders and I found that the files in both folders are identical.

    Is there any other information I can give you that will help me solve this issue?


  • Hero Member

    @dbemowsk the GET_LANG system error is a new one for me is Device 8 the MySensors Plugin Main device? You can check this if you press the arrow and then go to the Advanced. Under Params there is a variable valled "id". This is the device id.

    I see allso form your previous pictures that the overall system state of your Vera says "Your installation is not complete" I wonder if this is causing problems if you have not set up your location properties properly.
    Maybe you should try completing the setup of your Vera first.



  • @korttoma I am not sure what device 8 is. The MySensors device is 5 if I am reading this correctly:
    0_1482233434375_upload-1a51477f-da6a-4104-b784-a23c1479f18c

    I am assuming that this is what you are referring to when you say "Your installation is not complete" :
    0_1482233069559_upload-d4ccb584-2cf1-4f04-9166-7f07866b332b

    That was in the beginning, but if you notice it says "still no device is connected". I am sure that is why it says it is not complete. Here is the current status from the dashboard:
    0_1482233191770_upload-78cce839-acee-4e1a-b81e-e45bf2750ee9

    I am beginning to wondering if I shouldn't do a factory reset and start over. I think before I do that I am going to use the "COntact Customer Care" button.


  • Hero Member

    @dbemowsk Seems like the GET_LANG system error is not related to MySensors then. What else have you installed? Can you find this Device 8?

    Contacting Customer Care is a good idea but then you have to be patient because it can take a days before you get any answer and if you have not enabled the remote access and sent them the code they will just ask you to do this in their first answer and then you might have to wait for days again.

    Also take a look at the thread @blacey mentioned about how you could check that the plugin files are correct.


  • Hero Member

    I found this in the Vera forums:

    The GET_LANG(system_error,System error) is a small displaying error caused by our language tool that failed to import this language token.
    Regarding "Fail to load implementation file" issue, due to an old bug that we fixed recently, this message was not displayed. It appears when the implementation file for a device is not found on the gateway of the device parameters are wrong specified. This can be caused by manually created device from what I could see after debugging some units with this issue. To fix this issue you will need to delete the device that is showing the error like this :

    Code: [Select]

    http://gateway_address:3480/data_request?id=device&action=delete&device=device_id
    
    


  • As a side not I see Lib version is blank in the screen shot...



  • @r-nox What should the lib version be?

    So just to rule out other things that I may have done when trying to install some other apps, which by the way may have caused the error with device 8, I did a factory reset of the device and ran through the setup one more time. With the reset I was upgraded to a newer firmware version (1.7.2414). I re-uploaded the arduino files and created the device using the instructions on the MySensors website under the Vera controller. One thing I found curious is that when creating the device, the only thing it says to fill in on the "Create Device" page is the "Upnp Device FIlename". I was surprised that I didn't have to fill in any of the other fields such as the "Device Type" or the "Upnp Implementation Filename" . Again the device was created, and I configured the serial port as follows:
    0_1482278094094_upload-77a5482c-8792-41c9-9463-56f600f57f1f


    When I go to devices, things look the same as before. Here are the current screen shots:
    0_1482278193935_upload-9b95e586-53cc-4411-a5d0-a0aa5e4f1790


    0_1482278255917_upload-53ab1756-8086-4cb4-b701-8919f549e465


    0_1482278300939_upload-f1ab41ae-c846-4eaf-a386-7ea4d06de141


    0_1482278460104_upload-5287611b-e9df-4642-984a-e0838820878e


  • Hero Member

    Hi @dbemowsk

    You setup stil looked different from mine so I decided to wipe my VeraLite clean and see what I get.

    Now my setup looks exactly like yours except I did get the Lib version ( witch should show the Library version used in your MySensors Gateway ) efter hitting the reset button on my GW arduino and restart the Luup engine a few times.

    Then when I press the "Start" button I get the text bellow the buttons like this:

    0_1482299688258_upload-09006f39-4dfb-4f7d-a232-97ff83a1e1ff

    As I then restart a Sensor node the number count up according to the devices found and when I know it has fund them all I press "Stop". Then the luup engine restarts automatically and the new devices are created.

    I hit ctrl + F5 to refresh my browser and then go to devises and find this:

    0_1482299875190_upload-6e2835cc-1739-452c-96f8-e99164019fae

    So I think your system is fine, you just need to restart the GW and run a few luup restarts and refresh your browser. Then try including a Sensor.



  • @korttoma Is there any kind of command line serial monitor that I can use on the Vera to test my gateway communication coming into it? If not, that may be something for them to include on the unit. I double checked my wiring from my USB FTDI adapter to the gateway last night and I have my 3 wires as follows:

    FTDI.......GW
    GND ----GND
    TX --------- RX
    RX --------- TX

    I tried hitting the reset button on the gateway a number of times and restarted the luup engine a few times and also rebooted the Vera a few times. That is why I want to test that the Vera is receiving data from the FTDI properly.

    I am betting that it is something that I am doing wrong, and I am going to kick myself in the arse when I figure out what it is.


  • Hero Member

    You can see the vera log file if you enter this adress in your browser

    http://<YourVeraIP>/cgi-bin/cmh/log.sh?Device=LuaUPnP
    


  • @dbemowsk

    Check out this tool if you don't know about it already.
    https://www.mysensors.org/controller/myscontroller



  • @jlieffort I know about this tool, but this will not help. I need to debug the serial connection from my gateway to my Vera controller. This is a Windows based tool.



  • OK, I have an update with some log information, thanks @korttoma for the link. This is a snipet of the log:

    50	12/22/16 6:06:48.240	luup_log:9: Arduino: Requesting status for: 20;3 <0x74229520>
    50	12/22/16 6:06:49.270	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=0,pt=7,l=5,sg=0:19.44 <0x74229520>
    50	12/22/16 6:06:49.274	luup_log:9: Arduino: Set variable: 20;0;1;0;0;19.44 <0x74229520>
    50	12/22/16 6:06:49.279	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=44,pt=7,l=5,sg=0:18.89 <0x74229520>
    50	12/22/16 6:06:49.280	luup_log:9: Arduino: Set variable: 20;0;1;0;44;18.89 <0x74229520>
    50	12/22/16 6:06:49.297	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=45,pt=7,l=5,sg=0:18.89 <0x74229520>
    50	12/22/16 6:06:49.298	luup_log:9: Arduino: Set variable: 20;0;1;0;45;18.89 <0x74229520>
    50	12/22/16 6:06:49.305	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=44,pt=7,l=5,sg=0:27.22 <0x74229520>
    50	12/22/16 6:06:49.306	luup_log:9: Arduino: Set variable: 20;0;1;0;44;27.22 <0x74229520>
    50	12/22/16 6:06:49.857	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=2,c=2,t=47,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:49.858	luup_log:9: Arduino: Request: 20;2;2;0;47; <0x74229520>
    50	12/22/16 6:06:49.859	luup_log:9: Arduino: Requesting status for: 20;2 <0x74229520>
    50	12/22/16 6:06:51.416	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=3,c=2,t=47,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:51.417	luup_log:9: Arduino: Request: 20;3;2;0;47; <0x74229520>
    50	12/22/16 6:06:51.417	luup_log:9: Arduino: Requesting status for: 20;3 <0x74229520>
    50	12/22/16 6:06:52.445	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=0,pt=7,l=5,sg=0:19.44 <0x74229520>
    50	12/22/16 6:06:52.447	luup_log:9: Arduino: Set variable: 20;0;1;0;0;19.44 <0x74229520>
    50	12/22/16 6:06:52.496	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=45,pt=7,l=5,sg=0:18.89 <0x74229520>
    50	12/22/16 6:06:52.497	luup_log:9: Arduino: Set variable: 20;0;1;0;45;18.89 <0x74229520>
    50	12/22/16 6:06:53.090	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=2,c=2,t=47,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:53.091	luup_log:9: Arduino: Request: 20;2;2;0;47; <0x74229520>
    50	12/22/16 6:06:53.091	luup_log:9: Arduino: Requesting status for: 20;2 <0x74229520>
    50	12/22/16 6:06:54.657	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=3,c=2,t=47,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:54.657	luup_log:9: Arduino: Request: 20;3;2;0;47; <0x74229520>
    50	12/22/16 6:06:54.658	luup_log:9: Arduino: Requesting status for: 20;3 <0x74229520>
    50	12/22/16 6:06:55.160	luup_log:9: Arduino: Log: TSP:MSG:READ 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:55.161	luup_log:9: Arduino: Log: TSP:MSG:BC <0x74229520>
    50	12/22/16 6:06:55.164	luup_log:9: Arduino: Log: TSP:MSG:FPAR REQ (sender=255) <0x74229520>
    50	12/22/16 6:06:55.165	luup_log:9: Arduino: Log: TSP:CHKUPL:OK <0x74229520>
    50	12/22/16 6:06:55.167	luup_log:9: Arduino: Log: TSP:MSG:GWL OK <0x74229520>
    50	12/22/16 6:06:55.750	luup_log:9: Arduino: Log: TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=bc:0 <0x74229520>
    50	12/22/16 6:06:55.758	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=0,pt=7,l=5,sg=0:19.44 <0x74229520>
    50	12/22/16 6:06:55.761	luup_log:9: Arduino: Set variable: 20;0;1;0;0;19.44 <0x74229520>
    50	12/22/16 6:06:55.764	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=44,pt=7,l=5,sg=0:18.89 <0x74229520>
    50	12/22/16 6:06:55.765	luup_log:9: Arduino: Set variable: 20;0;1;0;44;18.89 <0x74229520>
    50	12/22/16 6:06:56.348	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=2,c=2,t=47,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:56.349	luup_log:9: Arduino: Request: 20;2;2;0;47; <0x74229520>
    50	12/22/16 6:06:56.350	luup_log:9: Arduino: Requesting status for: 20;2 <0x74229520>
    50	12/22/16 6:06:57.178	luup_log:9: Arduino: Log: TSP:MSG:READ 255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:57.180	luup_log:9: Arduino: Log: TSP:MSG:BC <0x74229520>
    50	12/22/16 6:06:57.186	luup_log:9: Arduino: Log: TSP:MSG:FPAR REQ (sender=255) <0x74229520>
    50	12/22/16 6:06:57.188	luup_log:9: Arduino: Log: TSP:CHKUPL:OK (FLDCTRL) <0x74229520>
    50	12/22/16 6:06:57.189	luup_log:9: Arduino: Log: TSP:MSG:GWL OK <0x74229520>
    50	12/22/16 6:06:57.735	luup_log:9: Arduino: Log: TSP:MSG:SEND 0-0-255-255 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=bc:0 <0x74229520>
    50	12/22/16 6:06:57.920	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=3,c=2,t=47,pt=0,l=0,sg=0: <0x74229520>
    50	12/22/16 6:06:57.920	luup_log:9: Arduino: Request: 20;3;2;0;47; <0x74229520>
    50	12/22/16 6:06:57.921	luup_log:9: Arduino: Requesting status for: 20;3 <0x74229520>
    50	12/22/16 6:06:58.941	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=0,pt=7,l=5,sg=0:19.44 <0x74229520>
    50	12/22/16 6:06:58.943	luup_log:9: Arduino: Set variable: 20;0;1;0;0;19.44 <0x74229520>
    50	12/22/16 6:06:58.961	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=44,pt=7,l=5,sg=0:18.89 <0x74229520>
    50	12/22/16 6:06:58.962	luup_log:9: Arduino: Set variable: 20;0;1;0;44;18.89 <0x74229520>
    50	12/22/16 6:06:58.973	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=45,pt=7,l=5,sg=0:18.89
    

    To me that looks like the gateway is receiving data. As I scanned through the log though, I noticed this:

    01	12/22/16 4:29:02.122	UserData::WriteUserData saved--before move File Size: 4541 save size 4541 <0x77229520>
    02	12/22/16 4:29:02.122	UserData::TempLogFileSystemFailure start 0 <0x77229520>
    02	12/22/16 4:29:02.140	UserData::TempLogFileSystemFailure 4287 res:1
    -rw-r--r--    1 root     root            33 Dec 20 16:30 /etc/cmh/HW_Key
    -rw-r--r--    1 root     root            32 Dec 31  1999 /etc/cmh/HW_Key2
    -rw-r--r--    1 root     root             9 Dec 20 16:30 /etc/cmh/PK_AccessPoint
    -rw-r--r--    1 root     root             7 Dec 20 17:14 /etc/cmh/PK_Account
    -rw-r--r--    1 root     root           425 Dec 21 01:29 /etc/cmh/cmh.conf
    -rw-r--r--    1 root     root             0 Aug 22 08:36 /etc/cmh/devices
    -rw-r--r--    1 root     root         16383 Dec 21 03:00 /etc/cmh/dongle.4.5.dump.0
    -rw-r--r--    1 root     root            41 Dec 20 16:21 /etc/cmh/ergy_key
    -rw-r--r--    1 root     root             0 Aug 22 08:36 /etc/cmh/first_boot
    -rw-r--r--    1 root     root             0 Dec 21 01:25 /etc/cmh/fresh_install
    -rw-r--r--    1 root     root             1 Dec 21 01:52 /etc/cmh/ip_mode
    -rw-r--r--    1 root     root            48 Dec 31  1999 /etc/cmh/keys
    -rw-r--r--    1 root     root             3 Dec  9 09:30 /etc/cmh/language
    -rw-r--r--    1 root     root             2 Dec  9 09:30 /etc/cmh/language_id
    -rw-r--r--    1 root     root            10 Dec 21 16:34 /etc/cmh/last_backup
    -rw-r--r--    1 root     root            11 Dec 22 01:52 /etc/cmh/last_report
    -rw-r--r--    1 root     root            70 Dec 20 16:36 /etc/cmh/lighttpd_failures
    -rw-r--r--    1 root     root         36316 Oct  3 00:25 /etc/cmh/network_pnp.lua
    -rw-r--r--    1 root     root            12 Dec  9 09:30 /etc/cmh/platform
    -rw-r--r--    1 root     root           458 Oct  3 00:25 /etc/cmh/ra_key
    -rw-r--r--    1 root     root             0 Dec  9 09:30 /etc/cmh/scenarios
    -rw-r--r--    1 root     root          2032 Dec 20 16:30 /etc/cmh/servers.conf
    -rw-r--r--    1 root     root          1520 Aug 22 08:34 /etc/cmh/servers.conf.default
    -rw-r--r--    1 root     root            20 Dec 20 16:35 /etc/cmh/servers.conf.timestamp
    -rw-r--r--    1 root     root           154 Oct  3 00:25 /etc/cmh/servers_whitelist
    -rw-r--r--    1 root     root          1598 Dec 22 01:52 /etc/cmh/services.conf
    -rw-r--r--    1 root     root            20 Dec 20 16:19 /etc/cmh/sync_kit
    -rw-r--r--    1 root     root            20 Dec 20 16:19 /etc/cmh/sync_rediscover
    -rw-r--r--    1 root     root             2 Dec  9 09:30 /etc/cmh/ui
    -rw-r--r--    1 root     root             2 Dec  9 09:30 /etc/cmh/ui_man
    -rw-r--r--    1 root     root             5 Dec  9 09:30 /etc/cmh/ui_skin
    -rw-r--r--    1 root     root           504 Jul 22 09:31 /etc/cmh/user_data.json.luup.lzo
    -rw-r--r--    1 root     root          4541 Dec 22 02:41 /etc/cmh/user_data.json.lzo
    -rw-r--r--    1 root     root          4540 Dec 22 02:05 /etc/cmh/user_data.json.lzo.1
    -rw-r--r--    1 root     root          4540 Dec 21 23:17 /etc/cmh/user_data.json.lzo.2
    -rw-r--r--    1 root     root          4541 Dec 21 21:53 /etc/cmh/user_data.json.lzo.3
    -rw-r--r--    1 root     root          4547 Dec 21 21:23 /etc/cmh/user_data.json.lzo.4
    -rw-r--r--    1 root     root          4544 Dec 21 17:05 /etc/cmh/user_data.json.lzo.5
    -rw-r--r--    1 root     root          4541 Dec 22 04:29 /etc/cmh/user_data.json.lzo.new
    -rw-r--r--    1 root     root            21 Dec 20 17:14 /etc/cmh/users.conf
    -rw-r--r--    1 root     root            20 Dec 20 17:14 /etc/cmh/users.conf.timestamp
    -rw-r--r--    1 root     root             3 Aug 22 08:36 /etc/cmh/vera_model
    -rw-r--r--    1 root     root             9 Dec  9 09:30 /etc/cmh/version
    -rw-r--r--    1 root     root             9 Dec 21 21:24 /etc/cmh/version_latest
    -rw-r--r--    1 root     root             5 Dec 31  1999 /etc/cmh/zigbee_version
    -rw-r--r--    1 root     root             8 Dec 22 04:17 /etc/cmh/zwave_house_id
    -rw-r--r--    1 root     root             3 Dec 31  1999 /etc/cmh/zwave_locale
    -rw-r--r--    1 root     root            48 Dec 21 01:56 /etc/cmh/zwave_version
    
    /etc/cmh/orig:
    -rw-r--r--    1 root     root             0 Dec  9 09:30 devices
    -rw-r--r--    1 root     root             0 Dec  9 09:30 first_boot
    -rw-r--r--    1 root     root             0 Dec  9 09:30 fresh_install
    -rw-r--r--    1 root     root             0 Dec  9 09:30 scenarios
    -rw-r--r--    1 root     root           520 Dec  9 09:30 user_data.json.lzo
    
    /etc/cmh/wan_failover:
    -rw-r--r--    1 root     root            44 Jul 22 09:31 check_internet.hosts
     <0x77229520>
    02	12/22/16 4:29:02.204	UserData::TempLogFileSystemFailure start 0 <0x77229520>
    02	12/22/16 4:29:02.223	UserData::TempLogFileSystemFailure 4198 res:1
    -rw-r--r--    1 root     root            33 Dec 20 16:30 /etc/cmh/HW_Key
    -rw-r--r--    1 root     root            32 Dec 31  1999 /etc/cmh/HW_Key2
    -rw-r--r--    1 root     root             9 Dec 20 16:30 /etc/cmh/PK_AccessPoint
    -rw-r--r--    1 root     root             7 Dec 20 17:14 /etc/cmh/PK_Account
    -rw-r--r--    1 root     root           425 Dec 21 01:29 /etc/cmh/cmh.conf
    -rw-r--r--    1 root     root             0 Aug 22 08:36 /etc/cmh/devices
    -rw-r--r--    1 root     root         16383 Dec 21 03:00 /etc/cmh/dongle.4.5.dump.0
    -rw-r--r--    1 root     root            41 Dec 20 16:21 /etc/cmh/ergy_key
    -rw-r--r--    1 root     root             0 Aug 22 08:36 /etc/cmh/first_boot
    -rw-r--r--    1 root     root             0 Dec 21 01:25 /etc/cmh/fresh_install
    -rw-r--r--    1 root     root             1 Dec 21 01:52 /etc/cmh/ip_mode
    -rw-r--r--    1 root     root            48 Dec 31  1999 /etc/cmh/keys
    -rw-r--r--    1 root     root             3 Dec  9 09:30 /etc/cmh/language
    -rw-r--r--    1 root     root             2 Dec  9 09:30 /etc/cmh/language_id
    -rw-r--r--    1 root     root            10 Dec 21 16:34 /etc/cmh/last_backup
    -rw-r--r--    1 root     root            11 Dec 22 01:52 /etc/cmh/last_report
    -rw-r--r--    1 root     root            70 Dec 20 16:36 /etc/cmh/lighttpd_failures
    -rw-r--r--    1 root     root         36316 Oct  3 00:25 /etc/cmh/network_pnp.lua
    -rw-r--r--    1 root     root            12 Dec  9 09:30 /etc/cmh/platform
    -rw-r--r--    1 root     root           458 Oct  3 00:25 /etc/cmh/ra_key
    -rw-r--r--    1 root     root             0 Dec  9 09:30 /etc/cmh/scenarios
    -rw-r--r--    1 root     root          2032 Dec 20 16:30 /etc/cmh/servers.conf
    -rw-r--r--    1 root     root          1520 Aug 22 08:34 /etc/cmh/servers.conf.default
    -rw-r--r--    1 root     root            20 Dec 20 16:35 /etc/cmh/servers.conf.timestamp
    -rw-r--r--    1 root     root           154 Oct  3 00:25 /etc/cmh/servers_whitelist
    -rw-r--r--    1 root     root          1598 Dec 22 01:52 /etc/cmh/services.conf
    -rw-r--r--    1 root     root            20 Dec 20 16:19 /etc/cmh/sync_kit
    -rw-r--r--    1 root     root            20 Dec 20 16:19 /etc/cmh/sync_rediscover
    -rw-r--r--    1 root     root             2 Dec  9 09:30 /etc/cmh/ui
    -rw-r--r--    1 root     root             2 Dec  9 09:30 /etc/cmh/ui_man
    -rw-r--r--    1 root     root             5 Dec  9 09:30 /etc/cmh/ui_skin
    -rw-r--r--    1 root     root           504 Jul 22 09:31 /etc/cmh/user_data.json.luup.lzo
    -rw-r--r--    1 root     root          4541 Dec 22 04:29 /etc/cmh/user_data.json.lzo
    -rw-r--r--    1 root     root          4541 Dec 22 02:41 /etc/cmh/user_data.json.lzo.1
    -rw-r--r--    1 root     root          4540 Dec 22 02:05 /etc/cmh/user_data.json.lzo.2
    -rw-r--r--    1 root     root          4540 Dec 21 23:17 /etc/cmh/user_data.json.lzo.3
    -rw-r--r--    1 root     root          4541 Dec 21 21:53 /etc/cmh/user_data.json.lzo.4
    -rw-r--r--    1 root     root          4547 Dec 21 21:23 /etc/cmh/user_data.json.lzo.5
    -rw-r--r--    1 root     root            21 Dec 20 17:14 /etc/cmh/users.conf
    -rw-r--r--    1 root     root            20 Dec 20 17:14 /etc/cmh/users.conf.timestamp
    -rw-r--r--    1 root     root             3 Aug 22 08:36 /etc/cmh/vera_model
    -rw-r--r--    1 root     root             9 Dec  9 09:30 /etc/cmh/version
    -rw-r--r--    1 root     root             9 Dec 21 21:24 /etc/cmh/version_latest
    -rw-r--r--    1 root     root             5 Dec 31  1999 /etc/cmh/zigbee_version
    -rw-r--r--    1 root     root             8 Dec 22 04:17 /etc/cmh/zwave_house_id
    -rw-r--r--    1 root     root             3 Dec 31  1999 /etc/cmh/zwave_locale
    -rw-r--r--    1 root     root            48 Dec 21 01:56 /etc/cmh/zwave_version
    
    /etc/cmh/orig:
    -rw-r--r--    1 root     root             0 Dec  9 09:30 devices
    -rw-r--r--    1 root     root             0 Dec  9 09:30 first_boot
    -rw-r--r--    1 root     root             0 Dec  9 09:30 fresh_install
    -rw-r--r--    1 root     root             0 Dec  9 09:30 scenarios
    -rw-r--r--    1 root     root           520 Dec  9 09:30 user_data.json.lzo
    
    /etc/cmh/wan_failover:
    -rw-r--r--    1 root     root            44 Jul 22 09:31 check_internet.hosts
     <0x77229520>
    

    The things that say TempLogFileSystemFailure are a bit of a red flag for me.

    Also, here is a log of what happens when I hit the start button to start inclusion.

    
    50	12/22/16 6:12:44.804	luup_log:9: Arduino: Requesting status for: 20;2 <0x74229520>
    08	12/22/16 6:12:45.587	JobHandler_LuaUPnP::HandleActionRequest device: 9 service: urn:upnp-arduino-cc:serviceId:arduino1 action: StartInclusion <0x75429520>
    08	12/22/16 6:12:45.588	JobHandler_LuaUPnP::HandleActionRequest argument DeviceNum=9 <0x75429520>
    08	12/22/16 6:12:45.588	JobHandler_LuaUPnP::HandleActionRequest argument serviceId=urn:upnp-arduino-cc:serviceId:arduino1 <0x75429520>
    08	12/22/16 6:12:45.588	JobHandler_LuaUPnP::HandleActionRequest argument action=StartInclusion <0x75429520>
    50	12/22/16 6:12:45.590	luup_log:9: Arduino: Sending: 0;0;3;0;5;1 <0x77bf1320>
    04	12/22/16 6:12:45.593	 <0x77bf1320>
    50	12/22/16 6:12:46.361	luup_log:9: Arduino: Log: TSP:MSG:READ 20-20-0 s=3,c=2,t=47,pt=0,l=0,sg=0: <0x74229520>
    

    It looks as if inclusion mode is starting, but nothing is happening.

    Maybe one of you has some insight as to what all of this information means.


  • Hero Member

    I'm not sure what to make of it, maybe @blacey, @petewill, @BartE or @hek could comment on this?



  • I am leaving for work in a few minutes, but if I don't hear something by the time I get off work, I am going to call tech support. I REALLY appreciate the help everyone has given.


  • Hero Member

    Hi @dbemowsk ,

    I wish I could do more to help you. I took a look at the log in my test environment and I found that I also have this:

    TempLogFileSystemFailure
    

    Maybe this is something that is printed each time the device restarts?? Let me know if Vera support gives you any explanation for it.

    But the MySensors Part seems to work fine for me:

    Here the USB port gets connected and Vera receives the Lib version of the GW:

    50	12/23/16 7:51:43.454	luup_log:5: Arduino: Trying for a serial connection <0x2bf65680>
    50	12/23/16 7:51:43.454	luup_log:5: Arduino: Serial port is connected <0x2bf65680>
    50	12/23/16 7:51:43.455	luup_log:5: Arduino: Baud is 115200 <0x2bf65680>
    50	12/23/16 7:51:43.456	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,GWAddress, 4(115200), 5 <0x2bf65680>
    06	12/23/16 7:51:43.456	Device_Variable::m_szValue_set device: 5 service: urn:upnp-arduino-cc:serviceId:arduino1 variable: GWAddress was: - now: 4(115200) #hooks: 0 upnp: 0 skip: 0 v:0xbcbed0/NONE duplicate:0 <0x2bf65680>
    50	12/23/16 7:51:43.459	luup_log:5: Arduino: Sending: 0;0;3;0;2;Get Version <0x2bf65680>
    50	12/23/16 7:51:43.471	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,ArduinoLibVersion, 2.0.0, 5 <0x2d565680>
    

    Here is what it looks like when I start inclusion mode and find one device:

    50	12/23/16 7:52:20.057	luup_log:5: Arduino: Sending: 0;0;3;0;5;1 <0x2b51c310>
    04	12/23/16 7:52:20.059	 <0x2b51c310>
    50	12/23/16 7:52:20.070	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,InclusionMode, 1, 5 <0x2d565680>
    06	12/23/16 7:52:20.071	Device_Variable::m_szValue_set device: 5 service: urn:upnp-arduino-cc:serviceId:arduino1 variable: InclusionMode was: 0 now: 1 #hooks: 0 upnp: 0 skip: 0 v:0xbb2eb8/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:20.072	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,InclusionFoundCountHR, 0 devices found, 5 <0x2d565680>
    06	12/23/16 7:52:20.073	Device_Variable::m_szValue_set device: 5 service: urn:upnp-arduino-cc:serviceId:arduino1 variable: InclusionFoundCountHR was:  now: 0 devices found #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:35.941	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-255 s=255,c=3,t=7,pt=0,l=0,sg=0: <0x2d565680>
    50	12/23/16 7:52:35.950	luup_log:5: Arduino: Log: TSP:MSG:BC <0x2d565680>
    50	12/23/16 7:52:35.952	luup_log:5: Arduino: Log: TSP:MSG:FPAR REQ (sender=3) <0x2d565680>
    50	12/23/16 7:52:35.954	luup_log:5: Arduino: Log: TSP:CHKUPL:OK <0x2d565680>
    50	12/23/16 7:52:35.955	luup_log:5: Arduino: Log: TSP:MSG:GWL OK <0x2d565680>
    50	12/23/16 7:52:36.711	luup_log:5: Arduino: Log: TSP:MSG:SEND 0-0-3-3 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=ok:0 <0x2d565680>
    50	12/23/16 7:52:37.981	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=255,c=3,t=24,pt=1,l=1,sg=0:1 <0x2d565680>
    50	12/23/16 7:52:37.991	luup_log:5: Arduino: Log: TSP:MSG:PINGED (ID=3, hops=1) <0x2d565680>
    50	12/23/16 7:52:38.001	luup_log:5: Arduino: Log: TSP:MSG:SEND 0-0-3-3 s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=ok:1 <0x2d565680>
    50	12/23/16 7:52:38.003	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=255,c=3,t=15,pt=6,l=2,sg=0:0100 <0x2d565680>
    50	12/23/16 7:52:38.011	luup_log:5: Arduino: Log: TSP:MSG:SEND 0-0-3-3 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100 <0x2d565680>
    50	12/23/16 7:52:38.021	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=255,c=0,t=17,pt=0,l=10,sg=0:2.0.1-beta <0x2d565680>
    50	12/23/16 7:52:38.022	luup_log:5: Arduino: Presentation: 3;255;0;0;17;2.0.1-beta <0x2d565680>
    50	12/23/16 7:52:38.025	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0 <0x2d565680>
    50	12/23/16 7:52:38.031	luup_log:5: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdate, 1482472358, 7 <0x2d565680>
    06	12/23/16 7:52:38.031	Device_Variable::m_szValue_set device: 7 service: urn:micasaverde-com:serviceId:HaDevice1 variable: LastUpdate was: 1482411882 now: 1482472358 #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:38.033	luup_log:5: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdateHR, 07:52, 7 <0x2d565680>
    06	12/23/16 7:52:38.033	Device_Variable::m_szValue_set device: 7 service: urn:micasaverde-com:serviceId:HaDevice1 variable: LastUpdateHR was: 15:04 now: 07:52 #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:38.034	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,RelayNode, 0, 7 <0x2d565680>
    50	12/23/16 7:52:38.035	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,RelayNodeHR, GW, 7 <0x2d565680>
    50	12/23/16 7:52:38.036	luup_log:5: Arduino: Sending: 3;255;3;0;6;M <0x2d565680>
    50	12/23/16 7:52:38.061	luup_log:5: Arduino: Log: TSP:MSG:SEND 0-0-3-3 s=255,c=3,t=6,pt=0,l=1,sg=0,ft=0,st=ok:M <0x2d565680>
    50	12/23/16 7:52:38.261	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=255,c=3,t=11,pt=0,l=7,sg=0:TempLux <0x2d565680>
    50	12/23/16 7:52:38.263	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,SketchName, TempLux, 7 <0x2d565680>
    50	12/23/16 7:52:38.265	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=255,c=3,t=12,pt=0,l=3,sg=0:2.0 <0x2d565680>
    50	12/23/16 7:52:38.270	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,SketchVersion, 2.0, 7 <0x2d565680>
    50	12/23/16 7:52:38.461	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=20,c=0,t=16,pt=0,l=0,sg=0: <0x2d565680>
    50	12/23/16 7:52:38.462	luup_log:5: Arduino: Presentation: 3;20;0;0;16; <0x2d565680>
    50	12/23/16 7:52:38.463	luup_log:5: Arduino: Found new device 3;20 <0x2d565680>
    50	12/23/16 7:52:38.464	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,InclusionFoundCountHR, 1 devices found, 5 <0x2d565680>
    06	12/23/16 7:52:38.465	Device_Variable::m_szValue_set device: 5 service: urn:upnp-arduino-cc:serviceId:arduino1 variable: InclusionFoundCountHR was: 0 devices found now: 1 devices found #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:38.471	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=0,c=0,t=6,pt=0,l=0,sg=0: <0x2d565680>
    50	12/23/16 7:52:38.472	luup_log:5: Arduino: Presentation: 3;0;0;0;6; <0x2d565680>
    50	12/23/16 7:52:38.474	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=255,c=3,t=26,pt=1,l=1,sg=0:2 <0x2d565680>
    50	12/23/16 7:52:38.521	luup_log:5: Arduino: Log: !TSP:MSG:SEND 0-0-3-3 s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=fail:1 <0x2d565680>
    50	12/23/16 7:52:39.041	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=20,c=1,t=23,pt=2,l=2,sg=0:912 <0x2d565680>
    50	12/23/16 7:52:39.042	luup_log:5: Arduino: Set variable: 3;20;1;0;23;912 <0x2d565680>
    50	12/23/16 7:52:39.901	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=0,c=1,t=0,pt=7,l=5,sg=0:22.6 <0x2d565680>
    50	12/23/16 7:52:39.902	luup_log:5: Arduino: Set variable: 3;0;1;0;0;22.6 <0x2d565680>
    50	12/23/16 7:52:39.903	luup_log:5: Arduino: Setting variable 'CurrentTemperature' to value '22.6' <0x2d565680>
    50	12/23/16 7:52:39.904	luup_log:5: Arduino: urn:upnp-org:serviceId:TemperatureSensor1,CurrentTemperature, 22.6, 6 <0x2d565680>
    06	12/23/16 7:52:39.905	Device_Variable::m_szValue_set device: 6 service: urn:upnp-org:serviceId:TemperatureSensor1 variable: CurrentTemperature was: 23.1 now: 22.6 #hooks: 0 upnp: 0 skip: 0 v:0xbcdf98/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:39.906	luup_log:5: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdate, 1482472359, 6 <0x2d565680>
    06	12/23/16 7:52:39.906	Device_Variable::m_szValue_set device: 6 service: urn:micasaverde-com:serviceId:HaDevice1 variable: LastUpdate was: 1482411882 now: 1482472359 #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:39.907	luup_log:5: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdate, 1482472359, 7 <0x2d565680>
    06	12/23/16 7:52:39.908	Device_Variable::m_szValue_set device: 7 service: urn:micasaverde-com:serviceId:HaDevice1 variable: LastUpdate was: 1482472358 now: 1482472359 #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:52:39.909	luup_log:5: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdateHR, 07:52, 7 <0x2d565680>
    08	12/23/16 7:53:00.180	JobHandler_LuaUPnP::HandleActionRequest device: 0 service: urn:micasaverde-com:serviceId:HomeAutomationGateway1 action: LogIpRequest <0x2e565680>
    08	12/23/16 7:53:00.181	JobHandler_LuaUPnP::HandleActionRequest argument serviceId=urn:micasaverde-com:serviceId:HomeAutomationGateway1 <0x2e565680>
    08	12/23/16 7:53:00.181	JobHandler_LuaUPnP::HandleActionRequest argument action=LogIpRequest <0x2e565680>
    08	12/23/16 7:53:00.182	JobHandler_LuaUPnP::HandleActionRequest argument IpAddress=192.168.1.6 <0x2e565680>
    08	12/23/16 7:53:00.182	JobHandler_LuaUPnP::HandleActionRequest argument MacAddress=e0:5f:45:12:68:73 <0x2e565680>
    08	12/23/16 7:53:03.507	JobHandler_LuaUPnP::HandleActionRequest device: 5 service: urn:upnp-arduino-cc:serviceId:arduino1 action: StopInclusion <0x2e565680>
    08	12/23/16 7:53:03.507	JobHandler_LuaUPnP::HandleActionRequest argument DeviceNum=5 <0x2e565680>
    08	12/23/16 7:53:03.508	JobHandler_LuaUPnP::HandleActionRequest argument serviceId=urn:upnp-arduino-cc:serviceId:arduino1 <0x2e565680>
    08	12/23/16 7:53:03.508	JobHandler_LuaUPnP::HandleActionRequest argument action=StopInclusion <0x2e565680>
    50	12/23/16 7:53:03.510	luup_log:5: Arduino: Sending: 0;0;3;0;5;0 <0x2b51c310>
    04	12/23/16 7:53:03.512	 <0x2b51c310>
    50	12/23/16 7:53:03.521	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,InclusionMode, 0, 5 <0x2d565680>
    06	12/23/16 7:53:03.521	Device_Variable::m_szValue_set device: 5 service: urn:upnp-arduino-cc:serviceId:arduino1 variable: InclusionMode was: 1 now: 0 #hooks: 0 upnp: 0 skip: 0 v:0xbb2eb8/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:53:03.522	luup_log:5: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,InclusionFoundCountHR, , 5 <0x2d565680>
    06	12/23/16 7:53:03.523	Device_Variable::m_szValue_set device: 5 service: urn:upnp-arduino-cc:serviceId:arduino1 variable: InclusionFoundCountHR was: 1 devices found now:  #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x2d565680>
    50	12/23/16 7:53:03.524	luup_log:5: Arduino: Inclusion mode ended. <0x2d565680>
    02	12/23/16 7:53:03.525	luup_log:5: Arduino: Found new sensor(s). Need to restart. Please wait. <0x2d565680>
    09	12/23/16 7:53:03.528	Child_Devices::ProcessChildDevice created device 10 id 3;20 under 5 topmost parent 5 <0x2d565680>
    

    Here is what it looks like when the device receives a value:

    50	12/23/16 7:54:15.122	luup_log:5: Arduino: Log: TSP:SANCHK:OK <0x2e07b680>
    50	12/23/16 7:54:52.352	luup_log:5: Arduino: Log: TSP:MSG:READ 3-3-0 s=20,c=1,t=23,pt=2,l=2,sg=0:913 <0x2e07b680>
    50	12/23/16 7:54:52.354	luup_log:5: Arduino: Set variable: 3;20;1;0;23;913 <0x2e07b680>
    50	12/23/16 7:54:52.354	luup_log:5: Arduino: Setting variable 'CurrentLevel' to value '913' <0x2e07b680>
    50	12/23/16 7:54:52.355	luup_log:5: Arduino: urn:micasaverde-com:serviceId:LightSensor1,CurrentLevel, 913, 10 <0x2e07b680>
    06	12/23/16 7:54:52.356	Device_Variable::m_szValue_set device: 10 service: urn:micasaverde-com:serviceId:LightSensor1 variable: CurrentLevel was: EMPTY now: 913 #hooks: 0 upnp: 0 skip: 0 v:0x911d88/NONE duplicate:0 <0x2e07b680>
    50	12/23/16 7:54:52.357	luup_log:5: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdate, 1482472492, 10 <0x2e07b680>
    


  • I placed a call to Vera yesterday The lady that I spoke with wasn't able to get anywhere and suggested that I email support@getvera.com and to leave remote assistance on. I referenced this thread in the email. Hopefully they will get back to me sometime today.



  • Another thing. Last night I decided that I would try getting some of my X10 stuff going with the Mochad X10 Gateway plugin. I seem to be having trouble with that too. I thought I would then just uninstall the plugin and wait for the Vera team to do their thing today, but it won't let me uninstall the plugin now. I click uninstall, it asks if I am sure I want to uninstall, I say yes, the green spinner comes up for about 10 seconds and then it says "Error uninstalling app, please try again".

    I have owned this box for going on a week now and I don't have anything running on it yet.



  • So, a question I have on this. Does Vera automatically define IDs for sensors or do I need to define them in my sketches?



  • Can anyone tell me what this means? Specifically the lines that end in "discarded for child: nil". In the Vera log, these lines show in yellow.

    
    50	12/25/16 23:01:50.974	luup_log:10: Arduino: Log: TSP:MSG:READ 4-4-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0 <0x7438f520>
    02	12/25/16 23:01:50.975	luup_log:10: Arduino: Incoming internal command '4;255;3;0;6;0' discarded for child: nil <0x7438f520>
    50	12/25/16 23:01:51.692	luup_log:10: Arduino: Log: TSP:MSG:READ 20-20-0 s=3,c=2,t=47,pt=0,l=0,sg=0: <0x7438f520>
    50	12/25/16 23:01:51.693	luup_log:10: Arduino: Request: 20;3;2;0;47; <0x7438f520>
    50	12/25/16 23:01:51.693	luup_log:10: Arduino: Requesting status for: 20;3 <0x7438f520>
    50	12/25/16 23:01:52.728	luup_log:10: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=0,pt=7,l=5,sg=0:21.11 <0x7438f520>
    50	12/25/16 23:01:52.729	luup_log:10: Arduino: Set variable: 20;0;1;0;0;21.11 <0x7438f520>
    50	12/25/16 23:01:52.735	luup_log:10: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=44,pt=7,l=5,sg=0:21.11 <0x7438f520>
    50	12/25/16 23:01:52.738	luup_log:10: Arduino: Set variable: 20;0;1;0;44;21.11 <0x7438f520>
    50	12/25/16 23:01:52.743	luup_log:10: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=45,pt=7,l=5,sg=0:21.11 <0x7438f520>
    50	12/25/16 23:01:52.747	luup_log:10: Arduino: Set variable: 20;0;1;0;45;21.11 <0x7438f520>
    50	12/25/16 23:01:52.763	luup_log:10: Arduino: Log: TSP:MSG:READ 20-20-0 s=0,c=1,t=44,pt=7,l=5,sg=0:27.22 <0x7438f520>
    50	12/25/16 23:01:52.765	luup_log:10: Arduino: Set variable: 20;0;1;0;44;27.22 <0x7438f520>
    50	12/25/16 23:01:52.966	luup_log:10: Arduino: Log: TSP:MSG:READ 4-4-0 s=255,c=3,t=11,pt=0,l=12,sg=0:MyGarageDoor <0x7438f520>
    02	12/25/16 23:01:52.968	luup_log:10: Arduino: Incoming internal command '4;255;3;0;11;MyGarageDoor' discarded for child: nil <0x7438f520>
    50	12/25/16 23:01:52.976	luup_log:10: Arduino: Log: TSP:MSG:READ 4-4-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.2 <0x7438f520>
    02	12/25/16 23:01:52.977	luup_log:10: Arduino: Incoming internal command '4;255;3;0;12;1.2' discarded for child: nil <0x7438f520>
    50	12/25/16 23:01:52.980	luup_log:10: Arduino: Log: TSP:MSG:READ 4-4-0 s=0,c=0,t=3,pt=0,l=0,sg=0: <0x7438f520>
    


  • So I got a response from Vera on my issue. Here was their response:


    Iโ€™ve checked your unit and the Arduino is flooding the Vera in a such way that it is crashing the engine. There is a configuration on the Arduino that is flooding the Vera unit or maybe there is an issue with the Arduino directly. Canโ€™t tell for sure.

    CUT some log info CUT

    If you remove the Arduino from the Vera, the engine will stop flooding and you will be able to access it the Vera unit and check it.

    Once you do that and check the configuration of the Arduino and also check to see if everything is alright with it, you will be able to plug it back in and the engine should not crash anymore and you shall be able to use the MySensor.

    With the configuration of the sensor you will need to check with MySensor directly as they have this information.


    Anyways, so I found that I had my thermostat bridge updating too often which was what was causing the supposed flooding. The bridge worked fine with Domoticz, so I really don't think that was the issue, though I could tone down the updates from it. I am not sure how he determined that it was crashing the engine, but for now I have the bridge disconnected and not flooding the gateway, and I still cannot add sensors.

    Any help that anyone can provide would be GREATLY appreciated. I have had the unit for over a week now and cannot add my MySensors devices.

    One good thing though, I did finally resolve the issue with my 1-wire server and I at least have my temp sensors online.

    Thanks guys


  • Hero Member

    Sorry I could not assist you during the holidays, I took a brake from tinkering and spent time with the family.
    I saw that you managed to narrow down the Vera MySensors issue to the FTDI adapter in the other thread.

    Just thought I would add the link to this in case someone else experiences the same problem, although it seems quite rare that this happens since you are the only one we know of so far.

    Lets hope your continued use of MySensors in Vera is smooth sailing from now on.



  • @korttoma Thanks. I completely understand the need for family.I should have thought to link the two topics myself.

    So far, since changing the FTDI adapter things have been for the most part smooth. The only thing I am having an issue with is my thermostat bridge node. Details are in this thread if you have any suggestions.


Log in to reply
 

Suggested Topics

  • 10
  • 3
  • 1
  • 6
  • 1

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts