Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Sensebender Micro Mechanical design

stefaanv last edited by

Hi,

I love the sensebender micro, having about five of them around the house measuring all kinds of things. Being able to buy the assembled PCB from the internet is great !

The compactness of the design is nice for building really small sensors, but in my humble opinion has one mayor drawback. There is no easy way to mechanically fix the PCB into a housing. Not suprisingly, I haven't seen a compelling case designs for the sensebender micro yet. Most designs have the board and the batteries floating inside.

I always end up fixing the naked PCB with two-sided tape to a wall or a to a piece of furniture, usually fixing the batteries right next to the sensor PCB in the same manner. The net effect being that my wife is becoming increasingly unsupportive of my MySensors hobby !

May I suggest that for future designs the wife factor is taken into account ? Two diagonal holes to fit screws and some free PCB space underneath for supports would be very helpfull.

Stefaan
Reply Quote 2
1 Reply Last reply

1
Posts

545
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Sensors and more
Hardware • • Robert Leverett

1

0
Votes

1
Posts

15
Views

No one has replied
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?
Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

5

1
Votes

5
Posts

70
Views

It probably has to do with fewer people buying them once summer ends, so companies might lower prices to clear out stock before winter.
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

27
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }

Sensebender Micro Mechanical design

Suggested Topics

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

Arduino Nano Every problem
Hardware • • hakha4

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

53
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Sensebender Micro Mechanical design

Suggested Topics

Over the air updates General Discussion • • ToSa

Sensors and more Hardware • • Robert Leverett

Arduino Nano Every problem Hardware • • hakha4

Best time of year to buy higher quality small project solar panels? Hardware • • NeverDie

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

53Online

11.4kUsers

11.1kTopics

112.7kPosts

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

Arduino Nano Every problem
Hardware • • hakha4

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

53
Online

11.4k
Users

11.1k
Topics

112.7k
Posts