[SOLVED] Node not uisng it´s ID!?

[siod]

I have a problem with one of my nodes. I assigned Node ID 10 to it, but it seems like it´s requesting an ID from the gateway!? This is my gateway output when I power on the Node:

0;255;3;0;9;3513128927 TSF:MSG:READ,255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;3513128933 TSF:MSG:BC
0;255;3;0;9;3513128936 TSF:MSG:FPAR REQ,ID=255
0;255;3;0;9;3513128941 TSF:PNG:SEND,TO=0
0;255;3;0;9;3513128944 TSF:CKU:OK
0;255;3;0;9;3513128947 TSF:MSG:GWL OK
0;255;3;0;9;3513130002 TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
0;255;3;0;9;3513130893 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;3513130900 Sending message on topic: mygateway1-out/255/255/3/0/3
0;255;3;0;9;3513132862 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;3513132869 Sending message on topic: mygateway1-out/255/255/3/0/3
0;255;3;0;9;3513134829 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;3513134836 Sending message on topic: mygateway1-out/255/255/3/0/3
0;255;3;0;9;3513136797 TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;3513136804 Sending message on topic: mygateway1-out/255/255/3/0/3
0;255;3;0;9;3513148605 TSF:MSG:READ,255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;3513148612 TSF:MSG:BC
0;255;3;0;9;3513148615 TSF:MSG:FPAR REQ,ID=255
0;255;3;0;9;3513148619 TSF:PNG:SEND,TO=0
0;255;3;0;9;3513148623 TSF:CKU:OK

and this is my Node´s sketch:

#define MY_RADIO_NRF24

#include <MySensors.h>
#include <SPI.h>


// Define Node ID
#define MY_NODE_ID 10
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC

//Batterysensor
int BATTERY_SENSE_PIN = A0;  // select the input pin for the battery sense point
int oldBatteryPcnt = 0;
#define CHILD_ID_BATT 7

//Kontaktschalter
#define CHILD_ID 1
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch


//MySensor gw;


// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_TRIPPED);
MyMessage msgbatt(CHILD_ID_BATT,V_VOLTAGE);

void setup()  
{  
  int  buzzer = 7;  //Buzzer Anschlusspin
  pinMode(buzzer, OUTPUT); 
  pinMode(13,OUTPUT);
  digitalWrite(13,HIGH); 
  digitalWrite(buzzer, HIGH);
  wait(50);
  digitalWrite(buzzer, LOW);
  wait(50);
  digitalWrite(buzzer, HIGH);
  wait(50);
  digitalWrite(buzzer, LOW);
  wait(50);
  digitalWrite(buzzer, HIGH);
  wait(50);
  digitalWrite(buzzer, LOW);
  //gw.begin(NULL, MY_NODE_ID, true);

 // Setup the button
  pinMode(BUTTON_PIN,INPUT);

  // Activate internal pull-up
  digitalWrite(BUTTON_PIN,HIGH);



    //Batterysensor
     // use the 1.1 V internal reference
#if defined(__AVR_ATmega2560__)
   analogReference(INTERNAL1V1);
#else
   analogReference(INTERNAL);
#endif
   // Send the sketch version information to the gateway and Controller
}
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  void presentation()
{
    sendSketchInfo("Wohunungstuer Alarm", "1.0");
    wait(500);
    present(CHILD_ID, S_DOOR);
    wait(500);
}


//  Check if digital input has changed and send in new value
void loop() 
{
     //Türkontakt prüfen:
  uint8_t value;
  static uint8_t sentValue = 2;
  
   value = digitalRead(BUTTON_PIN);

  if (value==HIGH){
         //Buzzer wird ausgelöst
       int  buzzer = 7;  //Buzzer Anschlusspin
  pinMode(buzzer, OUTPUT);
  digitalWrite(buzzer, HIGH);
  wait(500);
  digitalWrite(buzzer, LOW);
  wait(500);
  digitalWrite(buzzer, HIGH);
  wait(500);
  digitalWrite(buzzer, LOW);
  wait(500);
  digitalWrite(buzzer, HIGH);
  wait(500);
  digitalWrite(buzzer, LOW);
  wait(2000);
  digitalWrite(buzzer, HIGH);
  wait(500);
  digitalWrite(buzzer, LOW);
  wait(500);
  digitalWrite(buzzer, HIGH);
  wait(500);
  digitalWrite(buzzer, LOW);
  wait(500);
  digitalWrite(buzzer, HIGH);
  wait(500);
  digitalWrite(buzzer, LOW);  
  }


  // Short wait to allow buttons to properly settle
  wait(5);

  //Batterysensor
  // get the battery Voltage
   int sensorValue = analogRead(BATTERY_SENSE_PIN);
   #ifdef DEBUG
   Serial.println(sensorValue);
   #endif
   
   // 1M, 470K divider across battery and using internal ADC ref of 1.1V
   // Sense point is bypassed with 0.1 uF cap to reduce noise at that point
   // ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts
   // 3.44/1023 = Volts per bit = 0.003363075
   float batteryV  = sensorValue * 0.003363075;
   int batteryPcnt = sensorValue / 10;

   #ifdef DEBUG
   Serial.print("Battery Voltage: ");
   Serial.print(batteryV);
   Serial.println(" V");

   Serial.print("Battery percent: ");
   Serial.print(batteryPcnt);
   Serial.println(" %");
   #endif

   if (oldBatteryPcnt != batteryPcnt) {
     // Power up radio after sleep
     sendBatteryLevel(batteryPcnt);
     wait(500);
     send(msgbatt.set(batteryPcnt),true);
     wait(500);
     oldBatteryPcnt = batteryPcnt;
   }




  if (value != sentValue) {
    // Value has changed from last transmission, send the updated value
    send(msg.set(value == HIGH ? 1 : 0),true);
    wait(500);
    sentValue = value;
  }

  // Sleep until something happens with the sensor
  digitalWrite(13,LOW);
  Serial.println("Sleep");
  sleep(BUTTON_PIN - 2, CHANGE);// changing Secondary button to correct pin (-3) does not work. So keep it on (-2)
 }

What is wrong here?

[hek]

Move the MySensors include below your defines...

[siod]

damn it, that did the trick!! Just haven´t noticed...

Thx for your superfast support!!