Leaf Wetness

[hek]

It doesn't look much different that the china-ones. Is it gold-plated or something?

[epierre]

yes it is, from the hobby board site it is $2, but it is a quarter the china's size.

sorry I missed your point, it is gold plated, immersion gold.

[epierre]

Ok, so I made some adjustments from my last try:

• hobbyboard immersion gold sensor
• I kept the comparator from the other sensor to facilitate work with the arduino
• I've added a 18650 LiOn battery (5000mAh) to have an extended life cycle

Here is the sketch:
https://github.com/empierre/arduino/blob/master/LeafWetnessSensor.ino

What I can say, is that it is very sensitive. It is now outside live in the cold.

This could be used for a leak sensor easily.

[epierre]

so my 5000mAh lasted outside... 4 days... btw I didn't remove all leds from the comparator that could be an improvement and the outside weather is quite cold.

I had a reading every 30 secs, way to quick surely...

@hek is there a way to power the radio only when necessary ? I guess the gw.sleep could be a gw.sleep and a gw.wakeup and manage the delay outside ?

[hek]

@epierre

gw.sleep() sleeps the radio as well. What do you mean by power down radio? Like cutting power using digital pin?

[epierre]

@hek said:

@epierre

gw.sleep() sleeps the radio as well. What do you mean by power down radio? Like cutting power using digital pin?
yes, now you combine sleep for the radio and delay, what I mean is to have loop() run without radio, and if a transmission is needed to have a command that power it.

If you have a long dry period, a device on battery will consume a lot of power having the radion on and off, if it is always off until a sensor finds something, that would save more power, no ?

[RJ_Make]

Wake only on interrupt?

[epierre]

In my idea, a value above 0 would mean sending the info, an interrupt could be generated this way ?

[elisavetgrig]

Hey,
I am a newbie (in the forum) and in the arduino/sensors development. I bought the Leaf Wetness from cooking-hacks.com. Can I connected it to my Arduino via Analog input? Is it easy?

[Sparkman]

@elisavetgrig Welcome to the forum. The answer is yes to both questions. Given that the sensor is a resistive element, you need to build a voltage divider. Google "voltage divider" Arduino and you'll find lots of examples.

Cheers
Al

[FotoFieber]

Measuring the current with DC doesn't seem to be the ideal solution:
thread

[Sparkman]

@FotoFieber That thread is regarding soil moisture measurements which is different than leaf wetness. For soil, capacitive is the best way to go IMHO.

Cheers
Al

[FotoFieber]

AC Statement ☺

[elisavetgrig]

ok...Thank you... I will try the "voltage divider" and I will see what will happen!

[elisavetgrig]

[elisavetgrig]

Did you mean something like the figure above? Or I only need to connect one resistor to one wire and the other wire to another pin in the Arduino?

[Sparkman]

@elisavetgrig You're missing the connections to a voltage source and ground. You also only need one resistor as the wetness sensor is the 2nd resistor in the voltage divider circuit. Take a look at this: http://homepage.cs.uri.edu/faculty/hamel/workshops/as220-sept-09/sensors-voltage-dividers.html.

Cheers
Al

[elisavetgrig]

You are right! I thought that I missing something... always there are Data connection, VCC connection and GND.. and I had only one! I made another dummy scheme... Is that better?

[Sparkman]

@elisavetgrig Take a look at the second diagram of the link I posted. Right now you show the GND pin connected to the Analog pin and Vcc is also connected to the same spot, so that's not going to work.

Cheers
Al

[elisavetgrig]

I based in the second diagram... i think that I understand it...