[SOLVED] Sleep dont run

[mar.conte]

@tonnerre33
If i want sleep forever and wake only pir is high?

[HarryDutch]

@mar-conte
What happens if you change your sleep function like this:

sleep(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), HIGH,0);

[mar.conte]

@HarryDutch
I have try...
Nothing, the mcu dont sleep😭

[HarryDutch]

@mar.conte A shot in the dark but have you tried to pull down pin 3 in order to prevent this pin is floating? Connect pin 3 to ground with a 10K resistor.

[torfinn]

@mar.conte Hi ! Have the same problem with mysensor and NRF24l01. Tried to pull down both pins 4,5 (INT1/2) and even tried just to sleep(10000) without success. My circuit uses 17mA sending and 3,5mA when its supposed to sleep ???

[tonnerre33]

@torfinn said in Sleep dont run and @mar-conte :

Did you mesure the current consumed by the PIR when you are in sleep mode ?

[AWI]

@mar.conte I did some testing and I am experiencing a similar thing.
The node powers down (8 uA)with sleep( 5000 ); // sleep only
but with
sleep(INTERRUPT1, CHANGE, INTERRUPT2, CHANGE, 0 ); // sleep and wait for motion
or
sleep(INTERRUPT1, FALLING, INTERRUPT2, FALLING, 0 ); // sleep and wait for motion
it doesn't (2.5 mA)
I will do some additional testing ...:confused:

[gohan]

What library version are you using?

[mar.conte]

@mfalkvidd

0 MCO:BGN:INIT NODE,CP=RRNNA--,VER=2.1.1
4 TSM:INIT
4 TSF:WUR:MS=0
8 TSM:INIT:TSP OK
10 TSM:FPAR
141 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2148 !TSM:FPAR:NO REPLY
2150 TSM:FPAR
2281 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4288 !TSM:FPAR:NO REPLY
4290 TSM:FPAR
4421 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6430 !TSM:FPAR:NO REPLY
6432 TSM:FPAR
6563 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8574 !TSM:FPAR:FAIL
8577 TSM:FAIL:CNT=1
8579 TSM:FAIL:PDT

[mfalkvidd]

@mar.conte the node is unable to connect to your gateway so it never enters loop() and therefore never reaches the sleep statement.

[mar.conte]

@mfalkvidd
infact i the gw not exist, i try with gw and test again tanks

[mar.conte]

@mfalkvidd
what example in mysensors library i try?

[Yveaux]

@AWI See @tekka post here

"For indefinite sleeping, only level IRQ triggers are permitted (see AVR datasheet)."

Could you give that a try?

[gohan]

@mar.conte remember to set node ID

[mar.conte]

@gohan
one example to set node id in motion sketch?

[mar.conte]

RESOLVED

I HAVE JUST ONE GATEWAY CONFIGURED WITH RFM69 ON BOARD, THEN I HAVE CONNECTED TO NODE ID MCU WITH PIR AND EVERYTHING WORKS, WHEN THE PIR IS HIGH CURRENT CONSUMED is 2.25 MAH, WHEN IN SLEEP MODE ONLY 30 microamps.
THANKS TO ALL THAT I HAVE HELPED

NODE

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 *
 * DESCRIPTION
 * Motion Sensor example using HC-SR501
 * http://www.mysensors.org/build/motion
 *
 */

// Enable debug prints
 #define MY_DEBUG
#define MY_NODE_ID 1
// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69

#include <MySensors.h>

unsigned long SLEEP_TIME = 0; // Sleep time between reports (in milliseconds)
#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define CHILD_ID 1   // Id of the sensor child

// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()
{
	pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
}

void presentation()
{
	// Send the sketch version information to the gateway and Controller
	sendSketchInfo("Motion Sensor", "1.0");

	// Register all sensors to gw (they will be created as child devices)
	present(CHILD_ID, S_MOTION);
}

void loop()
{
	// Read digital motion value
	bool tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH;

	Serial.println(tripped);
	send(msg.set(tripped?"1":"0"));  // Send tripped value to gw

	// Sleep until interrupt comes in on motion sensor. Send update every two minute.
	sleep(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), CHANGE, SLEEP_TIME);
}

GATEWAY

/**
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2015 Sensnology AB
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
*******************************
*
* DESCRIPTION
* The ArduinoGateway prints data received from sensors on the serial link.
* The gateway accepts input on seral which will be sent out on radio network.
*
* The GW code is designed for Arduino Nano 328p / 16MHz
*
* Wire connections (OPTIONAL):
* - Inclusion button should be connected between digital pin 3 and GND
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
*
* LEDs (OPTIONAL):
* - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error
*
*/

// Enable debug prints to serial monitor
#define MY_DEBUG


// Enable and select radio type attached
//#define MY_RADIO_NRF24
#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <MySensors.h>

void setup()
{
	// Setup locally attached sensors
}

void presentation()
{
	// Present locally attached sensors
}

void loop()
{
	// Send locally attached sensor data here
}

SERIAL OUTPUT NODE

0 MCO:BGN:INIT NODE,CP=RRNNA--,VER=2.1.1
4 TSM:INIT
4 TSF:WUR:MS=0
8 TSM:INIT:TSP OK
10 TSM:INIT:STATID=1
12 TSF:SID:OK,ID=1
14 TSM:FPAR
145 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
1044 TSF:MSG:READ,0-0-1,s=255,c=3,t=8,pt=1,l=1,sg=0:0
1050 TSF:MSG:FPAR OK,ID=0,D=1
2152 TSM:FPAR:OK
2152 TSM:ID
2154 TSM:ID:OK
2156 TSM:UPL
2164 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2199 TSF:MSG:READ,0-0-1,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2205 TSF:MSG:PONG RECV,HP=1
2207 TSM:UPL:OK
2209 TSM:READY:ID=1,PAR=0,DIS=1
2263 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2287 TSF:MSG:READ,0-0-1,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2344 TSF:MSG:SEND,1-1-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
2404 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4421 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=11,pt=0,l=13,sg=0,ft=0,st=OK:Motion Sensor
4483 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4542 TSF:MSG:SEND,1-1-0-0,s=1,c=0,t=1,pt=0,l=0,sg=0,ft=0,st=OK:
4548 MCO:REG:REQ
4601 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4626 TSF:MSG:READ,0-0-1,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4630 MCO:PIM:NODE REG=1
4634 MCO:BGN:STP
4636 MCO:BGN:INIT OK,TSP=1
1
4689 TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=16,pt=0,l=1,sg=0,ft=0,st=OK:1
4698 MCO:SLP:MS=0,SMS=0,I1=1,M1=1,I2=255,M2=255
4702 MCO:SLP:TPD
4704 MCO:SLP:WUP=1
0
4714 TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=16,pt=0,l=1,sg=0,ft=0,st=OK:0
4722 MCO:SLP:MS=0,SMS=0,I1=1,M1=1,I2=255,M2=255
4726 MCO:SLP:TPD
4728 MCO:SLP:WUP=1
1
4739 TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=16,pt=0,l=1,sg=0,ft=0,st=OK:1
4747 MCO:SLP:MS=0,SMS=0,I1=1,M1=1,I2=255,M2=255
4751 MCO:SLP:TPD
4753 MCO:SLP:WUP=1
0
4763 TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=16,pt=0,l=1,sg=0,ft=0,st=OK:0
4771 MCO:SLP:MS=0,SMS=0,I1=1,M1=1,I2=255,M2=255
4775 MCO:SLP:TPD

SERIAL OUTPUT GATEWAY

0;255;3;0;9;MCO:BGN:INIT GW,CP=RRNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.1.1
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;TSF:MSG:READ,1-1-0,s=1,c=1,t=16,pt=0,l=1,sg=0:1
1;1;1;0;16;1

TANKS VERY VERY VERY TO ALL

[Yveaux]

@mar.conte Great to hear you nailed it!
For others to learn: what did you change to make things work?

[gohan]

@Yveaux I think he added the gateway as he wasn't using one

[mar.conte]

@gohan
Yes of course, add gateway and the loop end , the node attachinterrupt with pir go to sleep when gateway receive
Tanks

[torfinn]

Hi ! Just wanted to add that this also solved it for me. I had problem with properly registering on the gateway ( due to chips was used on old version earlier ). After finding this post I tried the https://www.mysensors.org/build/debug#clearing-eeprom and it fixed problem. Looking at 40uA sleeping now :-)