Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Updating to 1.5

Wackid last edited by Wackid

When i want to update to 1.5. I guess my current readings of Powerpulsmeter and waterpulsmeter are lost?

Is there a way to set those values over to the new version?
Reply Quote 0
1 Reply Last reply
hek Admin last edited by

No they won't.
Reply Quote 1
1 Reply Last reply
Wackid last edited by

Thanks... tried to update. But my serial is a Mega 2560.

So it gives an error. Remembers me i found a topic to switch the pins and change them in the sketch.
Reply Quote 0
1 Reply Last reply

3
Posts

1308
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2570
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
What's a good power bank for use with IoT?
General Discussion • • NeverDie

20

1
Votes

20
Posts

179
Views

@OldSurferDude Thanks a very valued to know. I was wondering today why my (big) powerbanks fall down after short time. I have small 1 & 2-pieces powerbanks, they work very well. I use also BSM hw-168 or hw-107 for charging single 18650. Will try to use them outside also with small solarpanels.
Running out of nodeId's
General Discussion • mysensors • • NielBierman

8

3
Votes

8
Posts

47
Views

@TheoL Not only did I put in delays, too, but I put in delays that were based upon the ID (which was stored in NVRAM)! This helped. caveat: This is probably not accurate be helps to explain the challenges with a large network. My initial experience with Arduino/nRF24 was using the libraries from TMRh20. Those libraries allowed a node to be a repeater, but only for 6 nodes. The primary node 0, master, only allowed 6 nodes to connect to it. The nodes connected to it also allowed 6 nodes. Subsequent nodes had to go through one of these repeating nodes. But the depth was only 4 deep. The master assigned node IDs if the node didn't already have one; similar to a MAC address. The master also kept track of the addresses (ARP table?). Addresses were 4 octets (base in the form of D/C/B/A. A node connected directly to the master had an address of 0/0/0/a (where 0/0/0/0 was reserved for the master). A node connected through another node had an address of 0/0/b/a, and so forth. But what happens is that a parent node has to mange the data from all its child nodes and their child nodes and their child nodes. Thus a node would get so bogged down dealing with this traffic that it din't do its sensor task very well. It is my belief that MySensors either uses TMRh20's libraries or has developed some aspects based on his initial work. I see that that TMRh20 has a version 2 and I have not experimented with it. I did find that MySensors worked better than version 1. Thus, my curiosity. I am also duly impressed at the magnitude of hardware. Currently a nano like device from Aliexperss is US$2-3, nRF24 ~ US$1, power supply ~ US$1.50, power cord ?, case?, sensors!? While the hardware cost is daunting, even with a PCB it's a lot of work building those up. So, yeah, I'm impressed! -OSD
single-click, double-click, long-press button possible with MySensors?
General Discussion • • dirkc

2

0
Votes

2
Posts

20
Views

hey @dirkc, maybe you can trigger your interrupt to rising and falling edge and use millis() to see how long the press was?
GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

15

0
Votes

15
Posts

123
Views

@eiten Ran into the same error but of course the community is always at hand, ready to help! Great! I'm using MySensors 2.3.2 release version. Downgrading the ESP8266 board library to 2.7.4 as suggested by @OldSurferDude did the trick. I'm still clinging to MySensors. So simple and inexpensive to use! All sensors and other stuff connects over three MQTT GW in three locations back to my Home Assistant. PS: Get well soon! Regards, Gunnar
Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini?
General Discussion • • kiesel

4

0
Votes

4
Posts

21
Views

Thanks for the offer @TheoL ! I have moved on to a differenct project. Also, a lesson that I have learned many times, "If it works, don't fix it!" -OSD

Updating to 1.5

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

What's a good power bank for use with IoT?
General Discussion • • NeverDie

Running out of nodeId's
General Discussion • mysensors • • NielBierman

single-click, double-click, long-press button possible with MySensors?
General Discussion • • dirkc

GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini?
General Discussion • • kiesel

53
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Updating to 1.5

Suggested Topics

Update RF24 library to latest version Bug Reports • • andriej

What's a good power bank for use with IoT? General Discussion • • NeverDie

Running out of nodeId's General Discussion • mysensors • • NielBierman

single-click, double-click, long-press button possible with MySensors? General Discussion • • dirkc

GatawayESP8266 - Compile error General Discussion • gatawayesp8266 compile error • • skom

Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini? General Discussion • • kiesel

53Online

11.4kUsers

11.1kTopics

112.7kPosts

Update RF24 library to latest version
Bug Reports • • andriej

What's a good power bank for use with IoT?
General Discussion • • NeverDie

Running out of nodeId's
General Discussion • mysensors • • NielBierman

single-click, double-click, long-press button possible with MySensors?
General Discussion • • dirkc

GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini?
General Discussion • • kiesel

53
Online

11.4k
Users

11.1k
Topics

112.7k
Posts