Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Add LF to Serial Gateway text?

NotTooTechy last edited by

Is there a configuration option to add line feeds to each line? I am using a windows program to read the serial port data and lack of line feeds is driving it nuts. I can't find anywhere to add LF but the text coming in definitely only have 0x0A on the end. I understand that is a C-thing but I need a Windows thing.
Reply Quote 0
1 Reply Last reply

1
Posts

647
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2570
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
No merge into master in the last 5 years, should we use development?
General Discussion • • kiesel

9

0
Votes

9
Posts

37
Views

For me almost all I need is in Master. For some nice to haves I have some custom libraries, like a message and a presentation queue. The only wish I have is dual led support.
Running out of nodeId's
General Discussion • mysensors • • NielBierman

8

3
Votes

8
Posts

47
Views

@TheoL Not only did I put in delays, too, but I put in delays that were based upon the ID (which was stored in NVRAM)! This helped. caveat: This is probably not accurate be helps to explain the challenges with a large network. My initial experience with Arduino/nRF24 was using the libraries from TMRh20. Those libraries allowed a node to be a repeater, but only for 6 nodes. The primary node 0, master, only allowed 6 nodes to connect to it. The nodes connected to it also allowed 6 nodes. Subsequent nodes had to go through one of these repeating nodes. But the depth was only 4 deep. The master assigned node IDs if the node didn't already have one; similar to a MAC address. The master also kept track of the addresses (ARP table?). Addresses were 4 octets (base in the form of D/C/B/A. A node connected directly to the master had an address of 0/0/0/a (where 0/0/0/0 was reserved for the master). A node connected through another node had an address of 0/0/b/a, and so forth. But what happens is that a parent node has to mange the data from all its child nodes and their child nodes and their child nodes. Thus a node would get so bogged down dealing with this traffic that it din't do its sensor task very well. It is my belief that MySensors either uses TMRh20's libraries or has developed some aspects based on his initial work. I see that that TMRh20 has a version 2 and I have not experimented with it. I did find that MySensors worked better than version 1. Thus, my curiosity. I am also duly impressed at the magnitude of hardware. Currently a nano like device from Aliexperss is US$2-3, nRF24 ~ US$1, power supply ~ US$1.50, power cord ?, case?, sensors!? While the hardware cost is daunting, even with a PCB it's a lot of work building those up. So, yeah, I'm impressed! -OSD
Gateway on Raspberry pi 1
General Discussion • • mimaret

9

0
Votes

9
Posts

44
Views

@mimaret It was a pleasure. Thank you for your feedback!
What's a good power bank for use with IoT?
General Discussion • • NeverDie

20

1
Votes

20
Posts

179
Views

@OldSurferDude Thanks a very valued to know. I was wondering today why my (big) powerbanks fall down after short time. I have small 1 & 2-pieces powerbanks, they work very well. I use also BSM hw-168 or hw-107 for charging single 18650. Will try to use them outside also with small solarpanels.
single-click, double-click, long-press button possible with MySensors?
General Discussion • • dirkc

2

0
Votes

2
Posts

20
Views

hey @dirkc, maybe you can trigger your interrupt to rising and falling edge and use millis() to see how long the press was?

Add LF to Serial Gateway text?

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

No merge into master in the last 5 years, should we use development?
General Discussion • • kiesel

Running out of nodeId's
General Discussion • mysensors • • NielBierman

Gateway on Raspberry pi 1
General Discussion • • mimaret

What's a good power bank for use with IoT?
General Discussion • • NeverDie

single-click, double-click, long-press button possible with MySensors?
General Discussion • • dirkc

9
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Add LF to Serial Gateway text?

Suggested Topics

Update RF24 library to latest version Bug Reports • • andriej

No merge into master in the last 5 years, should we use development? General Discussion • • kiesel

Running out of nodeId's General Discussion • mysensors • • NielBierman

Gateway on Raspberry pi 1 General Discussion • • mimaret

What's a good power bank for use with IoT? General Discussion • • NeverDie

single-click, double-click, long-press button possible with MySensors? General Discussion • • dirkc

9Online

11.4kUsers

11.1kTopics

112.7kPosts

Update RF24 library to latest version
Bug Reports • • andriej

No merge into master in the last 5 years, should we use development?
General Discussion • • kiesel

Running out of nodeId's
General Discussion • mysensors • • NielBierman

Gateway on Raspberry pi 1
General Discussion • • mimaret

What's a good power bank for use with IoT?
General Discussion • • NeverDie

single-click, double-click, long-press button possible with MySensors?
General Discussion • • dirkc

9
Online

11.4k
Users

11.1k
Topics

112.7k
Posts