Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Ebyte Lora UART radios - 433 MHz, Can only use Channels 433.00 and 434.00!

cloolalang last edited by

Re: Has anyone worked with e32-433t30d or any products related to EByte Company

I am looking into using these, but, wait... 1MHz channels:
ISM band 433MHz
Channels that you can use:
433.000
434,000
Thats it!
On no!... Why Ebyte?
P
Reply Quote 0
1 Reply Last reply

1
Posts

24
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50408
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Sensors and more
Hardware • • Robert Leverett

1

0
Votes

1
Posts

14
Views

No one has replied
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

69
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.
Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

5

1
Votes

5
Posts

65
Views

It probably has to do with fewer people buying them once summer ends, so companies might lower prices to clear out stock before winter.
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

20
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }

Ebyte Lora UART radios - 433 MHz, Can only use Channels 433.00 and 434.00!

Suggested Topics

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

Arduino Nano Every problem
Hardware • • hakha4

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

0
Online

11.4k
Users

11.1k
Topics

112.6k
Posts

Ebyte Lora UART radios - 433 MHz, Can only use Channels 433.00 and 434.00!

Suggested Topics

Over the air updates General Discussion • • ToSa

Sensors and more Hardware • • Robert Leverett

Arduino Nano Every problem Hardware • • hakha4

Which one should i choose? PIR or microwave sensor Hardware • • h01

Best time of year to buy higher quality small project solar panels? Hardware • • NeverDie

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

0Online

11.4kUsers

11.1kTopics

112.6kPosts

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

Arduino Nano Every problem
Hardware • • hakha4

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

0
Online

11.4k
Users

11.1k
Topics

112.6k
Posts