ESP8266 WiFi gateway issue

[snow]

Output from RPi console. pi@domoticz ~/domoticz $ sudo ./domoticz -verbose 1

2015-11-08 15:06:57.916  MySensors: connected to: 192.168.0.110:5003
2015-11-08 15:06:57.916  MySensors: Gateway Ready...
2015-11-08 15:06:58.917  MySensors: Gateway Version: 1.6.0-beta
2015-11-08 15:07:12.928  MySensors: Node: 3, Sketch Name: DimmableLED /w button
2015-11-08 15:07:13.932  MySensors: Node: 3, Sketch Version: 1.2
subtype       = AC
Sequence nbr  = 0
ID            = 0000003
Unit          = 1
Command       = On
2015-11-08 15:07:13.936  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 0
ID            = 0000003
Unit          = 1
Command       = Set Level: 12
2015-11-08 15:07:32.010  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 1
ID            = 0000003
Unit          = 1
Command       = Set Level: 11
2015-11-08 15:07:33.981  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 2
ID            = 0000003
Unit          = 1
Command       = Set Level: 10
2015-11-08 15:07:35.984  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 3
ID            = 0000003
Unit          = 1
Command       = Set Level: 9
2015-11-08 15:07:38.055  (MySensors) Lighting 2 (LED Dimmer)
subtype       = AC
Sequence nbr  = 4
ID            = 0000003
Unit          = 1
Command       = Set Level: 8

I'll try to build Serial Gateway and do the same test

[GizMoCuz]

There is a small problem with domoticz regarding the light level (fixed in beta #3563)
When the slider was set to 100%, around 93% was send to the node

BUT, what domoticz sends, is OK, there is NO version stuff added (really strange your seeing this!)

I made a test sketch, and this is the output:

Starting...
send: 254-254-0-0 s=255,c=0,t=17,pt=0,l=10,sg=0,st=ok:1.6.0-beta
send: 254-254-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-254 s=255,c=3,t=6,pt=0,l=1,sg=0:M
send: 254-254-0-0 s=1,c=0,t=4,pt=0,l=0,sg=0,st=ok:
send: 254-254-0-0 s=255,c=3,t=11,pt=0,l=21,sg=0,st=ok:DimmableLED /w button
send: 254-254-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.2
sensor started, id=254, parent=0, distance=1
Ready to receive messages...
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:0
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:0
V_LIGHT received: 0
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:1
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:1
V_LIGHT received: 1
read: 0-0-254 s=1,c=1,t=3,pt=0,l=2,sg=0:43
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:43
V_DIMMER received: 43
read: 0-0-254 s=1,c=1,t=3,pt=0,l=2,sg=0:86
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:86
V_DIMMER received: 86
read: 0-0-254 s=1,c=1,t=3,pt=0,l=3,sg=0:100
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=3,sg=0,st=ok:100
V_DIMMER received: 100

All perfect

Sketch:
// Enable debug prints
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#define MY_NODE_ID 254

#include <SPI.h>
#include <MySensor.h>

#define SN "DimmableLED /w button"
#define SV "1.2"

#define CHILD_ID_LIGHT 1

MyMessage dimmerMsg(CHILD_ID_LIGHT, V_DIMMER);

void setup()
{
Serial.println("Ready to receive messages...");
}

void presentation() {
// Send the Sketch Version Information to the Gateway
present(CHILD_ID_LIGHT, S_DIMMER);
sendSketchInfo(SN, SV);
}

void loop()
{
}

void receive(const MyMessage &message)
{
if (message.type == V_LIGHT) {
Serial.print("V_LIGHT received: ");
Serial.println(message.getString());
} else if (message.type == V_DIMMER) {
Serial.print("V_DIMMER received: ");
Serial.println(message.getString());
}
else {
Serial.print("Unhandled message received: ");
Serial.println(message.getString());
}
}

[hek]

@GizMoCuz
How do you terminate the strings in Domoticz? Only \n or both \n and \r?

Does the controller have exactly the same behaviour when communicating with an ethernet gateway as serial gateway?

[snow]

@GizMoCuz
I have tested Your sketch and the same stuff is added at the end

Starting...
send: 254-254-0-0 s=255,c=0,t=17,pt=0,l=10,sg=0,st=ok:1.6.0-beta
send: 254-254-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-254 s=255,c=3,t=6,pt=0,l=7,sg=0:Mersion
send: 254-254-0-0 s=1,c=0,t=4,pt=0,l=0,sg=0,st=ok:
send: 254-254-0-0 s=255,c=3,t=11,pt=0,l=21,sg=0,st=ok:DimmableLED /w button
send: 254-254-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.2
sensor started, id=254, parent=0, distance=1
Ready to receive messages...
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:0
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:0
V_LIGHT received: 0
read: 0-0-254 s=1,c=1,t=2,pt=0,l=1,sg=0:1
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:1
V_LIGHT received: 1
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:93Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:93Mersion
V_DIMMER received: 93Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:86Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:86Mersion
V_DIMMER received: 86Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:79Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:79Mersion
V_DIMMER received: 79Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:71Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:71Mersion
V_DIMMER received: 71Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:64Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:64Mersion
V_DIMMER received: 64Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:57Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:57Mersion
V_DIMMER received: 57Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:50Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:50Mersion
V_DIMMER received: 50Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:43Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:43Mersion
V_DIMMER received: 43Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:36Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:36Mersion
V_DIMMER received: 36Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:29Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:29Mersion
V_DIMMER received: 29Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:21Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:21Mersion
V_DIMMER received: 21Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:14Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:14Mersion
V_DIMMER received: 14Mersion
read: 0-0-254 s=1,c=1,t=3,pt=0,l=9,sg=0:74Mersion
send: 254-254-0-0 s=1,c=1,t=3,pt=0,l=9,sg=0,st=ok:74Mersion
V_DIMMER received: 74Mersion
read: 0-0-254 s=1,c=1,t=2,pt=0,l=9,sg=0:04Mersion
send: 254-254-0-0 s=1,c=1,t=2,pt=0,l=9,sg=0,st=ok:04Mersion
V_LIGHT received: 04Mersion

Is it possible as some crap is sitting in my ESP8266 EEPROM memory?

[GizMoCuz]

@hek, with \n
MySensors is implemented in domoticz for a long time now... there should be nothing wrong with it.....

Also in my sketches all is received perfectly

Could there be a difference between the ESP8266 and nRF ?
I only use the nRF currently (and probably will for ever as i have 20 more chips and a lot more arduino's g)

Also i do not send anything with the word version in it, it looks this is a left over from sending the sketch information ?

I dont know how you guys get that nice colors in the log (brown/white/green), but the green number is OK, that white behind it is not

[GizMoCuz]

@hek, as demonstrated with the new V_CUSTOM, there is send a lot of information from domoticz -> node, and all prints well, so maybe thats a confirm that this part is working OK (at least on the nRF024)

[GizMoCuz]

I also find it strange that at the beginning V_LIGHT correctly displays 0 or 1, and at the end 04 ? (0 = OK)

[snow]

I made a Serial Gateway and updated Domoticz to latest beta, and this is the output from the same sensor.

0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=1,sg=0,st=ok:7
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=1,sg=0:7
2;1;1;1;3;7
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:14
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:14
2;1;1;1;3;14
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:21
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:21
2;1;1;1;3;21
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:29
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:29
2;1;1;1;3;29
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:36
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:36
2;1;1;1;3;36
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:43
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:43
2;1;1;1;3;43
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:50
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:50
2;1;1;1;3;50
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:57
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:57
2;1;1;1;3;57
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:64
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:64
2;1;1;1;3;64
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:71
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:71
2;1;1;1;3;71
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:79
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:79
2;1;1;1;3;79
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:86
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:86
2;1;1;1;3;86
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:93
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:93
2;1;1;1;3;93
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=3,sg=0,st=ok:100
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=3,sg=0:100
2;1;1;1;3;100

All OK

[hek]

@snow

Could you try replacing this in MySensors/core/MyGatewayTransportEthernet.cpp

bool _readFromClient(uint8_t i) {
	while (clients[i].connected() && clients[i].available()) {
		char inChar = clients[i].read();
		if (inputString[i].idx < MY_GATEWAY_MAX_RECEIVE_LENGTH - 1) {
			// if newline then command is complete
			if (inChar == '\n') {
				// a command was issued by the client
				// we will now try to send it to the actuator
				// echo the string to the serial port
				debug(PSTR("Client %d: %s\n"), i, inputString[i].string);

				// add string terminator and clear the string:
				inputString[i].string[inputString[i].idx] = 0;
				inputString[i].idx = 0;
				bool ret = protocolParse(_ethernetMsg, inputString[i].string);
				if (ret) {
					return ret;
				}

			} else {
				// add it to the inputString:
				inputString[i].string[inputString[i].idx++] = inChar;
			}
		} else {
			// Incoming message too long. Throw away
			debug(PSTR("Client %d: Message too long\n"), i);
			inputString[i].idx = 0;
			// Finished with this client's message. Next loop() we'll see if there's more to read.
			break;
		}
	}
	return false;
}

And let me know how it behaves.

[GizMoCuz]

I think that will solve the issue... @snow, waiting patiently for your reply ;)

[snow]

It's much better now. I can control dimmer from the domoticz. :)

0;0;3;0;9;Client 0 connected
0;0;3;0;9;Client 0: 0;0;3;0;2;Get Version
0;0;3;0;2;Get Version
0;0;3;0;9;read: 2-2-0 s=255,c=0,t=17,pt=0,l=10,sg=0:1.6.0-beta
0;0;3;0;9;read: 2-2-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
0;0;3;0;9;Client 0: 2;255;3;0;6;M Version
2;255;3;0;6;M
0;0;3;0;9;send: 0-0-2-2 s=255,c=3,t=6,pt=0,l=1,sg=0,st=ok:M
0;0;3;0;9;read: 2-2-0 s=1,c=0,t=4,pt=0,l=0,sg=0:
0;0;3;0;9;read: 2-2-0 s=255,c=3,t=11,pt=0,l=21,sg=0:DimmableLED /w bu
0;0;3;0;9;read: 2-2-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.2
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=1,l=1,sg=0:100
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=1,l=1,sg=0,st=ok:100
0;0;3;0;9;Client 0: 2;1;1;1;3;93M
2;1;1;1;3;93
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:93
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:93
0;0;3;0;9;Client 0: 2;1;1;1;3;86
2;1;1;1;3;86
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:86
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:86
0;0;3;0;9;Client 0: 2;1;1;1;3;79
2;1;1;1;3;79
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:79
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:79
0;0;3;0;9;Client 0: 2;1;1;1;3;71
2;1;1;1;3;71
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:71
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:71
0;0;3;0;9;Client 0: 2;1;1;1;3;64
2;1;1;1;3;64
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:64
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:64
0;0;3;0;9;Client 0: 2;1;1;1;3;57
2;1;1;1;3;57
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:57
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:57
0;0;3;0;9;Client 0: 2;1;1;1;3;50
2;1;1;1;3;50
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:50
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:50
0;0;3;0;9;Client 0: 2;1;1;1;3;43
2;1;1;1;3;43
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:43
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:43
0;0;3;0;9;Client 0: 2;1;1;1;3;36
2;1;1;1;3;36
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:36
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:36
0;0;3;0;9;Client 0: 2;1;1;1;3;36
2;1;1;1;3;36
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:36
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:36
0;0;3;0;9;Client 0: 2;1;1;1;3;29
2;1;1;1;3;29
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:29
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:29
0;0;3;0;9;Client 0: 2;1;1;1;3;21
2;1;1;1;3;21
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:21
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:21
0;0;3;0;9;Client 0: 2;1;1;1;3;14
2;1;1;1;3;14
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=2,sg=0,st=ok:14
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=2,sg=0:14
0;0;3;0;9;Client 0: 2;1;1;1;3;74
2;1;1;1;3;7
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=0,l=1,sg=0,st=ok:7
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=0,l=1,sg=0:7
0;0;3;0;9;Client 0: 2;1;1;1;2;0
2;1;1;1;2;0
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=2,pt=0,l=1,sg=0,st=ok:0
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=2,pt=0,l=1,sg=0:0
0;0;3;0;9;read: 2-2-0 s=1,c=1,t=3,pt=2,l=2,sg=0:0
0;0;3;0;9;send: 0-0-2-2 s=1,c=1,t=3,pt=2,l=2,sg=0,st=ok:0

[hek]

Great, I'll push this fix ASAP.

[Hoffan]

@Hoffan said:
anyone that knows if include button working now? With vera as controller

[Hoffan]

I can answer that question by my self.. Its still not working

[hek]

@Hoffan, I verified the inclusion button functionality in the dev branch during the weekend (at least on AtMega but it should work fine on ESP as well).

Just make sure to enable the feature and set a valid ESP-pin. All is documented in sketch.

[Hoffan]

@hek

Okey So i must enable it in the sketch even if i only use the start button in the GUI in Vera

[hek]

@Hoffan
Not the "button" feature (unless you use it), but the "inclusion mode" feature must be enabled.

[Hoffan]

I don't know if i understan you right here, @Hek

if i like to use the start button in vera should it look like this

// Enable inclusion mode
define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN 3

[hek]

You only need these two:

#define MY_INCLUSION_MODE_FEATURE
#define MY_INCLUSION_MODE_DURATION 60

[Hoffan]

Yes That i understand, But Nothing is still happening in the GUI men i press start