Double Micro (nano) Ampere meter
-
I need this! Please publish instructions ;)
-
Wow, that looks nice, I'm stucked with my multimeter and couldn't find the parts avaiable for delivery here to build a µcurrent gold.
Please publish the build instructions !
(Maybe if you could give use the BOM first, then you'll have plenty of time to publish build instruction before we get delivered ;)) -
Awsome!
I'd like to compare your impressive array of measurement devices against my Agilent U1273A. Actually to decide if I need a µCurrent.... Maybe in an upcoming meetup in NL or BE this summer?
-
There it is Micro (nano) ampere meter (double). I need to add a schematic drawing. Any suggestions/ questions are welcome.
-
Parts ordered :D
-
@gohan As mentioned in the description: I use it as a "patch panel" to distribute the power and ground to different devices. Wiring tends to get messy on my workbench...
Not mine but similar ;-)@AWI - did you steal my image on my workbench ;) j/k.
We need to revive the old workbench topic again! -
@gohan No special tolerance resistors needed. The only reason for choosing metal film resistors is that their temperature coefficient is better than carbon types (typical 50ppm/°C compared to 200-500ppm/°C).
As you will be calibrating the circuit you can choose from a large range (0.1 Ohm - 100 Ohm) for the shunt. This will only influence the burden voltage / sensitivity and range (Ohm's laws). -
@DavidZH Impressive only by numbers ;-) I am prepared to trade my µCurrent for the Agilent :blush:
A meetup sounds good..any specific plans yet? -
A very low current (double) stand alone uA meter to tune MySensors battery nodes..
I de' MySensor'ized this project because it is more usefull on the workbench for measuring the very low currents of MySensors battery nodes. I own several Ampere meters including the famous µCurrent. Many of these are not accurate enough or need a lot of wiring and additional equipment (µCurrent). I just wanted something simple and stand alone
Using the low cost HX711 weight scale 24 bit AD converter a sub 10€ cost double µA meter was born. Some characteristics to fit MySensors projects:- range channel A: ± 20mA 5½-6½ digit µA
- range channel B: ±40mA 5½-6½ digit µA
- burden voltage 1µV/1µA (internal resistance 1Ω)
- 'patch panel' on the connectors.
- easy calibration.
In comparison with the µCurrent and a standard multimeter in uA range
The internals:
Although it cannot compare in accuracy with the µCurrent (in combination with a good multimeter) it is more than useable and accurate to do some serious MySensors tuning.
If there is some interest I will try to publish a decent built instruction on Openhardware.io.
If there is some interest I will try to publish a decent built instruction on Openhardware.io.
I'm interested.
-
If there is some interest I will try to publish a decent built instruction on Openhardware.io.
I'm interested.
@NeverDie said in Double Micro (nano) Ampere meter:
I'm interested.
In case you haven't seen it, it's here :
https://forum.mysensors.org/topic/6723/micro-nano-ampere-meter-double/5 -
@NeverDie said in Double Micro (nano) Ampere meter:
I'm interested.
In case you haven't seen it, it's here :
https://forum.mysensors.org/topic/6723/micro-nano-ampere-meter-double/5@Nca78 said in Double Micro (nano) Ampere meter:
@NeverDie said in Double Micro (nano) Ampere meter:
I'm interested.
In case you haven't seen it, it's here :
https://forum.mysensors.org/topic/6723/micro-nano-ampere-meter-double/5Thanks! It looks a bit complicated to me. I've used one of these breakout boards (https://www.amazon.com/gp/product/B00OPVBEQO/ref=oh_aui_search_detailpage?ie=UTF8&psc=1) as a way to measure 24-bit voltage on capacitors, and it works really well. As you can perhaps tell from the photo:
the chip is fairly simple to use. What I especially liked is that there was already a demo arduino sketch for interfacing with it. That was a real time saver. If I were to build something, I might try that first, if only because it seems like it might be easier (though perhaps, in part, because I'm already comfortable with it). Would using it in conjunction with a sense resistor be all it would take to make an accurate, high resolution current sensor? -
@Nca78 said in Double Micro (nano) Ampere meter:
@NeverDie said in Double Micro (nano) Ampere meter:
I'm interested.
In case you haven't seen it, it's here :
https://forum.mysensors.org/topic/6723/micro-nano-ampere-meter-double/5Thanks! It looks a bit complicated to me. I've used one of these breakout boards (https://www.amazon.com/gp/product/B00OPVBEQO/ref=oh_aui_search_detailpage?ie=UTF8&psc=1) as a way to measure 24-bit voltage on capacitors, and it works really well. As you can perhaps tell from the photo:
the chip is fairly simple to use. What I especially liked is that there was already a demo arduino sketch for interfacing with it. That was a real time saver. If I were to build something, I might try that first, if only because it seems like it might be easier (though perhaps, in part, because I'm already comfortable with it). Would using it in conjunction with a sense resistor be all it would take to make an accurate, high resolution current sensor? -
@Nca78 said in Double Micro (nano) Ampere meter:
@NeverDie said in Double Micro (nano) Ampere meter:
I'm interested.
In case you haven't seen it, it's here :
https://forum.mysensors.org/topic/6723/micro-nano-ampere-meter-double/5Thanks! It looks a bit complicated to me. I've used one of these breakout boards (https://www.amazon.com/gp/product/B00OPVBEQO/ref=oh_aui_search_detailpage?ie=UTF8&psc=1) as a way to measure 24-bit voltage on capacitors, and it works really well. As you can perhaps tell from the photo:
the chip is fairly simple to use. What I especially liked is that there was already a demo arduino sketch for interfacing with it. That was a real time saver. If I were to build something, I might try that first, if only because it seems like it might be easier (though perhaps, in part, because I'm already comfortable with it). Would using it in conjunction with a sense resistor be all it would take to make an accurate, high resolution current sensor?@NeverDie said in Double Micro (nano) Ampere meter:
It looks a bit complicated to me
btw. Which part looks complicated? It's just a few resistors attached to an ADC board (and sketch ready) I am curious on how you can build something simpler with the ADS1220 (which seems to be a better ADC if you are able to find it somewhere ;-))
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login