Hardware

OK, this worked and I am encouraged! I haven't figured out how to get the status LED's to work yet though, since they just stay on (after enabling it in the config H file). Unless I missed it though, I do not know what the fields are that are output via serial. If I do not find the info, I guess I could just reverse-engineer the software to figure out how to send simple data back and forth from each unit. Pretty cool library! Heavy though, but not as heavy as expected. I still have room for my RGB LED effects processing. Now I just need to see if my interrupt handling using timer1 is going to hose this library. Any thoughts?

Video streaming! Yeah baby :tada:

@martinhjelmare: yep, I like the vid too. it's funny to see all these new materials. :) you are right, I will use parts of rollershutternode I think, for the ac powered version. for the batt powered, I will use my "camel" sensor board plus others thing of others boards I made. I totally agree with you. When I do something I try to keep things reusable. As I am originally software dev, I always think factorizing, libs like a toolbox...lol. But I think electronician do the same.

@jeti said: @Nicola-Reina said: Anybody wanting 10 kits at a bargain price. I am sellling them at bargain price due to lack of time to play with them. If you are in Rome I can hand it over directly . If you are at EU maker faire this week end even better see you there. Otherwise I ship them too KR Still got the 10Kits? You can still buy these kits from my homepage.

@drock1985 Maybe some hints here.

Automatically controlled drones as part of the security system, anyone? :stuck_out_tongue_winking_eye:

Finally found the repo for what i think is the raspberry pi MQTT Gateway... Link, I'm assuming the file i need to be looking at is the MyGatewayTransportMQTTClient.cpp. However, there is no MakeFile there, am i being stupid or blind, how would i compile this gateway file to then be able to run it?

@epierre said: @alexsh1 said: Depends on your sensor. you do not have to add anything. yes and no, you don't have a datasheet for the board... 10K is 10K so you know it ;-) Actually, I have the datasheet for my board and this is adjustable resistor :) Anyway, I got mine working without any additional 10k resistors. I hope it helps.

@Sparkman You are right. The pin names on the sensebender, corresponds to the pin names on the arduinos, so the interrupt on D3 is the same as on the arduino.

So it is the same as Nano (2 and 3 only) - many thanks!!!

@siklosi thanks, so that means this module would be only good for serial monitor? Is it possible to do serial monitoring with mysbootloader / myscontroller? I am currently using serial gw with vera - if I am to use myscontroller do I have to disconnect it from vera and connect it with computer running myscontroller?

@Magnus-Pernemark It's all ceramics.. (also the 4.7uF for radio)

@tbowmo said: http://forum.mysensors.org/topic/1965/nodered-injected-between-domoticz-and-mysensors Thank you for the answer. I'll take a look at that.

I had the same problem a few months ago. The problem solved powering the arduino from a different power supply. You can read a bout it here Node freezing up No more problems since

Thanks a lot @AWI for the suggestions and explaination, even if it's a little difficult for me to understand. I have to take some other for other LED strips. So I'll take IRLZ34N or BUZ71 instead my BUZ91A so they didn't get so much hot. :-) Simon

Ok, finally I found the Problem. I changed the prescaler value of Timer0 becuase I needed a higher PWM Frequenciy. Unfortuneatly this also affects the millis() function that is used in gw.wait. It turns out taht with the changed TImer 0 Prescaler 1ms was not 1ms anymore but less. So the gw.wait(750) where only 750ms/64 which is not enough for DS18S20 conversion to take place.