Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 MDMSPanel "Nextion"

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/676/MDMSPanel-Nextion
Reply Quote 1
1 Reply Last reply
sebdetours last edited by

Hello Kalina.

Really good job. I like the way you designed your products. (not only this one

A question about the Box. Did you take a standart case that you cut out, or did you have your own case made from a manufacturer?

Regards
Reply Quote 0
1 Reply Last reply
kalina Hardware Contributor last edited by @sebdetours

@sebdetours said in MDMSPanel "Nextion":

Did you take a standart case that you cut out?

Hi @sebdetours, yes. This is G1910 (Gainta) box. See drawing attached to projet files.
Reply Quote 0
1 Reply Last reply

arduino 119 rtc 5 atmega 3 modbus 3 display 3 nextion 3 st485 2 jtag 2 megacore 1

3
Posts

749
Views

Log in to reply

Suggested Topics

Arduino Mini Pro 5v - how to power
Troubleshooting • arduino power pro mini • • ddluk

31

0
Votes

31
Posts

27601
Views

@epierre said: Both need protection (internal or external) from excessive discharge (or excessive charge, and short circuits etc) That is where our new library to check battery level goes in, we could dream to have an internal mysensor security check of a LiPo battery ! they do so in 'copters I may pass on that. I'm not used to software glitches having quite so much potential impact, and I don't need to save every gram. But to each their own!
How to check if serial gateway is operational ?
Development • arduino serial gateway • • joshmosh

4

0
Votes

4
Posts

2214
Views

@fot said: Hi! I ask my gateway about it's version (0;0;3;0;2;). It will responde with the library version number (1.4.1 in my case). It tells me that the gateway software is up and running. But it will not give me any clue about if the (NRF)network is working. That's a problem, right. I only ask the gateway if no other packages are received in $timeout seconds. /Magnus Of course ! Thank you for pushing my nose on it. Sometimes you don't see the most obvious Since my gateway is relatively close to the controller (Domoticz on a Raspi), I can do a hard reset of the gateway (via Raspi GPIO), which should resolve the issue. Cheers Josh
Pressure sensor and input trough optocoupler
Domoticz • arduino • • Olaf Jacobs

4

0
Votes

4
Posts

31
Views

@Olaf-Jacobs It's a straight analogue read on a single ADC pin relative to Vcc and ground of the Arduino Node. In my case it's a pro-mini, the ADC pin in this example earlier defined as "Pressure", the result radioed in only if the ADC reading has changed. Three other binary inputs for contactors are polled every second on separate digital pins (one of which is pin 3), which uses all 4 pins available on this pro-mini due to the radio etc. if ((!hidro&&!Hidro&&(counter2>=132))||initialise){ int incoming=analogRead(Pressure); if (prevolume!=incoming){ prevolume=incoming; sleep(50); float tankvolume=(((incoming-102.3)*6.704199635)+0.5);//5psi sensor send(msg8.set(tankvolume,0));//This is actual volume sleep(100); }} I'm not clear on the rest of what you're trying to incorporate or what pin 3 (digital interrupt) has to do with it, the pressure sensor signal goes to an analogue pin to enable the voltage to be read.
Lua Startup Failure (*SOLVED*)
Vera • arduino veralite • • rafael.brasilia

31

0
Votes

31
Posts

23006
Views

I'll admit a newbie at this. but I"m about beyond frustrated. I've been trying to get my "Vera Edge" Serial gateway up and running. I had it working, using a nano ATmega328 w/FTDI chipset. So that was great! All your posts were very helpful! So I decided to move forward and start building my sensors. The first sensor I built was a motion sensor also using a nano ATmega328. So I got it up and running, communicating with the gateway, and than the Vera controller dropped it and I kept get the same error message, Device not ready, "LUA Startup Failure. If you all have any another ideas on what could be causing this I could sure use your help! Thanks
Neopixel Node, using 1.6.0 Beta
My Project • arduino nodered ws2312 neopixels • • cranky

7

4
Votes

7
Posts

4943
Views

Oh, @msebbe @AWI , I have a FastLED version with a decent web API and web interface available here: http://forum.mysensors.org/topic/2705/fastled-neopixel-ws2811-node-from-arduino-code-to-web-page-with-api It's working pretty damn well Still working on my front end interface, since I'm not a designer (well, I am a 3d cad designer, not web dev). Oh, and if you knew my controller's name, you could communicate with it via TOR. Just like corporate solutions, I can communicate and control my gateway from anywhere in the world!
💬 learning cube for arduino
OpenHardware.io • arduino pcb microcontroller electronics learning teaching education • • openhardware.io

2

0
Votes

2
Posts

507
Views

But it's not a cube!
💬 Anna2040 RP2040 Uno-shaped board
OpenHardware.io • arduino uno arduino uno pico • • openhardware.io

1

0
Votes

1
Posts

8
Views

No one has replied

1
Online

11.4k
Users

11.1k
Topics

112.6k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1